Na3MnTi(PO4)3/C Nanofiber Free-Standing Electrode for Long-Cycling-Life Sodium-Ion Batteries.

Self-standing Na3MnTi(PO4)3/carbon nanofiber (CNF) electrodes are successfully synthesized by electrospinning. A pre-synthesized Na3MnTi(PO4)3 is dispersed in a polymeric solution, and the electrospun product is heat-treated at 750 °C in nitrogen flow to obtain active material/CNF electrodes. The active material loading is 10 wt%. SEM, TEM, and EDS analyses demonstrate that the Na3MnTi(PO4)3 particles are homogeneously spread into and within CNFs. The loaded Na3MnTi(PO4)3 displays the NASICON structure; compared to the pre-synthesized material, the higher sintering temperature (750 °C) used to obtain conductive CNFs leads to cell shrinkage along the a axis. The electrochemical performances are appealing compared to a tape-casted electrode appositely prepared. The self-standing electrode displays an initial discharge capacity of 124.38 mAh/g at 0.05C, completely recovered after cycling at an increasing C-rate and a coulombic efficiency ≥98%. The capacity value at 20C is 77.60 mAh/g, and the self-standing electrode exhibits good cycling performance and a capacity retention of 59.6% after 1000 cycles at 1C. Specific capacities of 33.6, 22.6, and 17.3 mAh/g are obtained by further cycling at 5C, 10C, and 20C, and the initial capacity is completely recovered after 1350 cycles. The promising capacity values and cycling performance are due to the easy electrolyte diffusion and contact with the active material, offered by the porous nature of non-woven nanofibers.

Temperature and pH Stimuli-Responsive System Delivers Location-Specific Antimicrobial Activity with Natural Products.

Smart materials with controlled stimuli-responsive functions are at the forefront of technological development. In this work, we present a generic strategy that combines simple components, physicochemical responses, and easy fabrication methods to achieve a dual stimuli-responsive system capable of location-specific antimicrobial cargo delivery. The encapsulated system is fabricated by combining a biocompatible inert polymeric matrix of poly(dimethylsiloxane) (PDMS) and a bioactive cargo of saturated fatty acids. We demonstrate the effectiveness of our approach to deliver antimicrobial activity for the model bacteria Escherichia coli. The system responds to two control variables, temperature and pH, delivering two levels of antimicrobial response under distinct combinations of stimuli: one response toward the planktonic media and another response directly at the surface for sessile bacteria. Spatially resolved Raman spectroscopy alongside thermal and structural material analysis reveals that the system not only exhibits ON/OFF states but can also control relocation and targeting of the active cargo toward either the surface or the liquid media, leading to different ON/OFF states for the planktonic and sessile bacteria. The approach proposed herein is technologically simple and scalable, facing low regulatory barriers within the food and healthcare sectors by using approved components and relying on fundamental chemical processes. Our results also provide a proof-of-concept platform for the design and easy fabrication of delivery systems capable of operating as Boolean logic gates, delivering different responses under different environmental conditions.

The Effect of Y Content on Structural and Sorption Properties of A2B7-Type Phase in the La-Y-Ni-Al-Mn System.

Metal hydrides are an interesting group of chemical compounds, able to store hydrogen in a reversible, compact and safe manner. Among them, A2B7-type intermetallic alloys based on La-Mg-Ni have attracted particular attention due to their high electrochemical hydrogen storage capacity (∼400 mAh/g) and extended cycle life. However, the presence of Mg makes their synthesis via conventional metallurgical routes challenging. Replacing Mg with Y is a viable approach. Herein, we present a systematic study for a series of compounds with a nominal composition of La2-xYxNi6.50Mn0.33Al0.17, x = 0.33, 0.67, 1.00, 1.33, 1.67, focusing on the relationship between the material structural properties and hydrogen sorption performances. The results show that while the hydrogen-induced phase amorphization occurs in the Y-poor samples (x < 1.00) already during the first hydrogen absorption, a higher Y content helps to maintain the material crystallinity during the hydrogenation cycles and increases its H-storage capacity (1.37 wt.% for x = 1.00 vs. 1.60 wt.% for x = 1.67 at 50 °C). Thermal conductivity experiments on the studied compositions indicate the importance of thermal transfer between powder individual particles and/or a measuring instrument.

Imaging and spectral analysis of autofluorescence patterns in larval head structures of mosquito vectors.

Autofluorescence (AF) in mosquitoes is currently poorly explored, despite its great potential as a marker of body structures and biological functions. Here, for the first time AF in larval heads of two mosquitoes of key public health importance, Aedes albopictus and Culex pipiens, is studied using fluorescence imaging and spectrofluorometry, similarly to a label-free histochemical approach. In generally conserved distribution patterns, AF shows differences between mouth brushes and antennae of the two species. The blue AF ascribable to resilin at the antennal bases, more extended in Cx. pipiens, suggests a potential need to support different antennal movements. The AF spectra larger in Cx. pipiens indicate a variability in material composition and properties likely relatable to mosquito biology, including diverse feeding and locomotion behaviours with implications for vector control.

Self-Supported Fibrous Sn/SnO2@C Nanocomposite as Superior Anode Material for Lithium-Ion Batteries.

Low-cost and simple methods are constantly chased in order to produce less expensive lithium-ion batteries (LIBs) while possibly increasing the energy and power density as well as the volumetric capacity in order to boost a rapid decarbonization of the transport sector. Li alloys and tin-carbon composites are promising candidates as anode materials for LIBs both in terms of capacity and cycle life. In the present paper, electrospinning was employed in the preparation of Sn/SnOx@C composites, where tin and tin oxides were homogeneously dispersed in a carbonaceous matrix of carbon nanofibers. The resulting self-standing and light electrode showed a greatly enhanced performance compared to a conventional electrode based on the same starting materials that are simply mixed to obtain a slurry then deposited on a Cu foil. Fast kinetics were achieved with more than 90% of the reaction that resulted being surface-controlled, and stable capacities of about 300 mAh/g over 500 cycles were obtained at a current density of 0.5 A/g.

Chemical and Physical Characterisation of Macroaggregated Human Serum Albumin: Strength and Specificity of Bonds with 99mTc and 68Ga.

BACKGROUND: Macroaggregated human serum albumin (MAA) properties are widely used in nuclear medicine, labelled with 99mTc. The aim of this study is to improve the knowledge about the morphology, size, dimension and physical-chemical characteristics of MAA and their bond with 99mTc and 68Ga. METHODS: Commercial kits of MAA (Pulmocis®) were used. Characterisation through experiments based on SEM, DLS and Stokes' Law were carried out. In vitro experiments for Langmuir isotherms and pH studies on radiolabelling were performed and the stability of the radiometal complex was verified through competition reactions. RESULTS: The study settles the MAA dimension within the range 43-51 µm. The Langmuir isotherm reveals for [99mTc]MAA: Bmax (46.32), h (2.36); for [68Ga]MAA: Bmax (44.54), h (0.893). Dual labelling reveals that MAA does not discriminate different radioisotopes. Experiments on pH placed the optimal pH for labelling with 99mTc at 6. CONCLUSION: Radiolabelling of MAA is possible with high efficiency. The nondiscriminatory MAA bonds make this drug suitable for radiolabelling with different radioisotopes or for dual labelling. This finding illustrates the need to continue investigating MAA chemical and physical characteristics to allow for secure labelling with different isotopes.

Collection and Characterization of Wood Decay Fungal Strains for Developing Pure Mycelium Mats.

Wood decay fungi (WDF) seem to be particularly suitable for developing myco-materials due to their mycelial texture, ease of cultivation, and lack of sporification. This study focused on a collection of WDF strains that were later used to develop mycelium mats of leather-like materials. Twenty-one WDF strains were chosen based on the color, homogeneity, and consistency of the mycelia. The growth rate of each strain was measured. To improve the consistency and thickness of the mats, an exclusive method (newly patented) was developed. The obtained materials and the corresponding pure mycelia grown in liquid culture were analyzed by both thermogravimetric analysis (TGA) and scanning electron microscopy (SEM) to evaluate the principal components and texture. TGA provided a semi-quantitative indication on the mycelia and mat composition, but it was hardly able to discriminate differences in the production process (liquid culture versus patented method). SEM provided keen insight on the mycelial microstructure as well as that of the mat without considering the composition; however, it was able to determine the hyphae and porosity dimensions. Although not exhaustive, TGA and SEM are complementary methods that can be used to characterize fungal strains based on their desirable features for various applications in bio-based materials. Taking all of the results into account, the Fomitopsis iberica strain seems to be the most suitable for the development of leather-like materials.

Zaltoprofen/4,4'-Bipyridine: A Case Study to Demonstrate the Potential of Differential Scanning Calorimetry (DSC) in the Pharmaceutical Field.

The Zaltoprofen/4,4'-Bipyridine system gives rise to two co-crystals of different compositions both endowed - in water and in buffer solution at pH 4.5 - with considerably higher solubility and dissolution rate than the pure drug. The qualitative and quantitative analysis of the DSC measurements, carried out on samples made up of mixtures prepared according to different methodologies, allows us to elaborate and propose an accurate thermodynamic model that fully takes into account the qualitative aspects of the complex experimental framework and which provides quantitative predictions (reaction enthalpies and compositions of the co-crystals) in excellent agreement with the experimental results. Co-crystal formation and cocrystal compositions were confirmed by X-ray diffraction measurements as well as by FT-IR and NMR spectroscopy measurements. The quantitative processing of DSC measurements rationalizes and deepens the scientific aspects underlying the so-called Tammann's triangle and constitutes a model of general validity. The work shows that DSC has enormous potential, which however can be fully exploited only by paying adequate attention to the experimental aspects and the quantitative processing of the measurements.

The Physico-Chemical Properties of Glipizide: New Findings.

The present work is a concrete example of how physico-chemical studies, if performed in depth, are crucial to understand the behavior of pharmaceutical solids and constitute a solid basis for the control of the reproducibility of the industrial batches. In particular, a deep study of the thermal behavior of glipizide, a hypoglycemic drug, was carried out with the aim of clarifying whether the recognition of its polymorphic forms can really be done on the basis of the endothermic peak that the literature studies attribute to the melting of the compound. A number of analytical techniques were used: thermal techniques (DSC, TGA), X-ray powder diffraction (XRPD), FT-IR spectroscopy and scanning electron microscopy (SEM). Great attention was paid to the experimental design and to the interpretation of the combined results obtained by all these techniques. We proved that the attribution of the endothermic peak shown by glipizide to its melting was actually wrong. The DSC peak is no doubt triggered by a decomposition process that involves gas evolution (cyclohexanamine and carbon dioxide) and formation of 5-methyl-N-[2-(4-sulphamoylphenyl) ethyl] pyrazine-2-carboxamide, which remains as decomposition residue. Thermal treatments properly designed and the combined use of DSC with FT-IR and XRPD led to identifying a new polymorphic form of 5-methyl-N-[2-(4-sulphamoylphenyl) ethyl] pyrazine-2-carboxamide, which is obtained by crystallization from the melt. Hence, our results put into evidence that the check of the polymorphic form of glipizide cannot be based on the temperature values of the DSC peak, since such a peak is due to a decomposition process whose Tonset value is strongly affected by the particle size. Kinetic studies of the decomposition process show the high stability of solid glipizide at room temperature.

Using the Emission of Muonic X-rays as a Spectroscopic Tool for the Investigation of the Local Chemistry of Elements.

There are several techniques providing quantitative elemental analysis, but very few capable of identifying both the concentration and chemical state of elements. This study presents a systematic investigation of the properties of the X-rays emitted after the atomic capture of negatively charged muons. The probability rates of the muonic transitions possess sensitivity to the electronic structure of materials, thus making the muonic X-ray Emission Spectroscopy complementary to the X-ray Absorption and Emission techniques for the study of the chemistry of elements, and able of unparalleled analysis in case of elements bearing low atomic numbers. This qualitative method is applied to the characterization of light elements-based, energy-relevant materials involved in the reaction of hydrogen desorption from the reactive hydride composite Ca(BH4)2-Mg2NiH4. The origin of the influence of the band-structure on the muonic atom is discussed and the observed effects are attributed to the contribution of the electronic structure to the screening and to the momentum distribution in the muon cascade.

Clickable cellulosic surfaces for peptide-based bioassays.

The use of peptides in paper-based analytics is a highly appealing field, yet it suffers from severe limitations. This is mostly due to the loss of effective target recognition properties of this relatively small probes upon nonspecific adsorption onto cellulose substrates. Here we address this issue by introducing a simple polymer-based strategy to obtain clickable cellulose surfaces, that we exploited for the chemoselective bioconjugation of peptide bioprobes. Our method largely outperformed standard adsorption-based immobilization strategy in a challenging, real case immunoassay, namely the diagnostic discrimination of Zika + individuals from healthy controls. Of note, the clickable polymeric coating not only allows efficient peptides bioconjugation, but it provides favorable anti-fouling properties to the cellulosic support. We envisage our strategy to broaden the repertoire of cellulosic materials manipulation and promote a renewed interest in peptide-based paper bioassays.

Enhancing the Pharmaceutical Behavior of Nateglinide by Cocrystallization: Physicochemical Assessment of Cocrystal Formation and Informed Use of Differential Scanning Calorimetry for Its Quantitative Characterization.

The aim of this study was to synthetize cocrystals of nateglinide, an antidiabetic agent of biopharmaceutics classification system Class IIa, as a strategy to improve both the solubility and the dissolution rate of the drug. Benzamide was selected by a screening procedure as a suitable coformer, and binary mixtures with different compositions were prepared and analyzed by differential scanning calorimetry (DSC). An in-depth analysis of DSC data allowed obtaining both the eutectic mixture and cocrystal compositions. The rationale of such an analysis was highlighted and explained. Cocrystals were prepared by kneading and solvent evaporation. Their formation was proved by DSC and confirmed by X-ray powder diffraction, solid-state nuclear magnetic resonance, and Fourier-transform infrared spectroscopy. The functional groups involved in the interaction leading to cocrystals formation were investigated by spectroscopic techniques. The in vitro dissolution profiles show that cocrystals have definite better pharmaceutical performances than the pure drug.

Multicomponent crystals of gliclazide and tromethamine: preparation, physico-chemical, and pharmaceutical characterization.

OBJECTIVE: To improve the pharmaceutical behavior of the oral antidiabetic agent gliclazide through the synthesis of multicomponent crystals with tromethamine. METHODS: Multicomponent crystals were prepared by solvent evaporation method, kneading, and combining mechanical and thermal activation. DSC, FT-IR spectroscopy, X-ray diffraction, SEM-EDS, and SSNMR were used to investigate their formation. Measurements of solubility and dissolution rate were carried out for the pharmaceutical characterization. RESULTS: The formation of multicomponent crystals of gliclazide and tromethamine was confirmed by all the techniques. In particular, FT-IR and NMR measurements revealed that the interaction between drug and coformer leads to significant changes of the hydrogen bond scheme, and that almost all the functional groups of the two molecules are involved. The dissolution profile of the new phase is significantly better than that of both pure gliclazide and of the reference commercial product Diabrezide®. CONCLUSIONS: The new system shows an improved pharmaceutical behavior and could be formulated in a dosage form to obtain a rapid and complete release of the drug available for absorption.

Optimal hydrogen storage in sodium substituted lithium fullerides.

Through the substitution of Li with Na in Li6C60, we synthesized a series of mixed alkali cluster intercalated fullerides, NaxLi6-xC60. These compounds share lattices of Na6C60 and Li6C60 with a cubic parameter linearly dependent on x. H2 absorption and desorption were studied by means of charge/discharge kinetic measurements and coupled calorimetric-manometric evaluation. By varying the stoichiometry, we found the best compromise among the absorption rate, temperature and amount of hydrogen for x = 0.5 and 1. Small concentrations of Na substituted to Li significantly lower the absorption temperature of Li6C60, improving the hydrogenation capacity, the kinetics, and the dehydrogenation enthalpy, the latter being 43.8 kJ mol-1 H2 for x = 1. This study moves further toward the utilization of intercalated fullerides for hydrogen storage applications.

Electrospun fibers as potential carrier systems for enhanced drug release of perphenazine.

Solubility represents an important challenge for formulation of drugs, because the therapeutic efficacy of a drug depends on the bioavailability and ultimately on its solubility. Low aqueous solubility is one of the main issues related with formulation design and development of new molecules. Many drug molecules present bioavailability problems due to their poor solubility. For this reason there is a great interest in the development of new carrier systems able to enhance the dissolution of poorly water-soluble drugs. In this work, fibers containing an insoluble model drug and prepared by an electrospinning method, are proposed and evaluated to solve this problem. Two hydrophilic polymers, polyvinylpyrrolidone (Plasdone® K29/32) and polyvinyl caprolactam-polyvinyl acetate-polyethylene glycol graft copolymer (Soluplus®) were used to increase the water solubility of perphenazine. The physico-chemical characterization suggests that the drug loaded in the fibers is in the amorphous state. Both polymeric carriers are effective to promote the drug dissolution rate in water, where this active pharmaceutical ingredient is insoluble, due to the fine dispersion of the drug into the polymeric matrices, obtained with this production technique. In fact, the dissolution profiles of the fibers, compared to the simple physical mixture of the two components, and to the reference commercial product Trilafon® 8mg tablets, show that a strong enhancement of the drug dissolution rate can be achieved with the electrospinning technique.

Mechanochemical synthesis of bumetanide-4-aminobenzoic acid molecular cocrystals: a facile and green approach to drug optimization.

Molecular cocrystals are of growing interest in pharmaceutics for their improved physicochemical properties. Their mechanochemical synthesis is very promising, being easy, cheap, and "green". Here, for the first time, we report on cocrystallization of bumetanide, a diuretic and natriuretic active principle, and 4-aminobenzoic acid. The synthesis is performed both by wet and dry grinding. The cocrystal formation was investigated with a wide range of techniques, including solid-state NMR, IR, XRD, microscopy, and thermal analysis. Wet and dry grinding procedures led to different cocrystal polymorphs. In particular, the dry method gave a cocrystal by powder amorphization and subsequent crystallization. DFT calculations at the B3LYP/6-31+G(d,p) level of theory shed light on the H-bond scheme at the basis of cocrystal formation. The cocrystals showed improved solubility and dissolution rate with respect to the drug alone. This could guarantee a faster absorption and a better bioavailability of the active principle.

Preparation and physicochemical characterization of acyclovir cocrystals with improved dissolution properties.

Acyclovir is a well-known antiviral agent. It can be administered in very high doses (from 200 to 1000 mg even three-four times daily). It has absorption problems mainly due to its poor solubility in water (about 0.2 g/100 mL at 25°C) and its oral bioavailability is approximately 15%-20% with a half-life of about 3 h. To improve acyclovir solubility and/or its dissolution properties, two cocrystals of this drug were successfully produced with glutaric acid (AGA1:1) and fumaric acid (AFA1:1) as conformers, using a cogrinding method. Their effective formation was investigated by a broad range of techniques: thermal analysis, Fourier transform infrared spectroscopy, X-ray powder diffraction, solid state nuclear magnetic resonance, and scanning electron microscopy coupled with energy dispersive X-ray spectrometry. The water solubility of the AGA1:1 cocrystal was not improved in comparison to acyclovir, while AFA1:1 showed a slight increased solubility at equilibrium. The main difference was detected in terms of intrinsic dissolution rates (IDR). The IDR of the new phases were much faster compared with acyclovir, particularly at neutral pH. AFA1:1 showed the most rapid dissolution behavior in water; within 10 min, the drug was released completely, while just 60% of acyclovir was dissolved in 1 h.

Structure and properties of domperidone and its succinate salt.

This paper describes the structure and properties of the drug domperidone and a novel 1:1 domperidone succinate salt. The new salt is characterized by means of thermal, spectroscopic, microscopic and powder diffraction measurements. The crystal structures of the salt and, for the first time, of pure domperidone have been determined by means of single-crystal X-ray diffraction. In both structures, the piperidine ring of domperidone adopts the expected chair conformation, and supramolecular centrosymmetric R2(2)(8) motifs are formed by N-H...O hydrogen bonds between chlorine-substituted oxobenzimidazolyl groups. Further N-H...O hydrogen bonds occur between non-substituted oxobenzimidazolyl groups and the resulting C(4) motifs originates hydrogen-bonded chains, extending along the crystallographic b axis. In the salt, a single N-H...O hydrogen bond forms between the protonated nitrogen of the piperidine ring and the carboxylic O atom of the succinate ion. Two alternative and mutually exclusive positions for the nonsubstituted oxobenzimidazolyl group have also been observed; this disorder makes the hydrogen-bonded chains originating from the bicyclic group polar. The dissolution behaviour of the salt in dosage form is compared with two reference commercial products. The salt shows an increased solubility, a characteristic that could be of great advantage from a pharmaceutical view point.

An experimental and theoretical investigation of loperamide hydrochloride-glutaric acid cocrystals.

Cocrystallization is a powerful method to improve the physicochemical properties of drugs. Loperamide hydrochloride is a topical analgesic for the gastrointestinal tract showing low and pH-dependent solubility; for this reason, an enhancement of its solubility or dissolution rate, particularly at the pH of the intestinal tract, could improve its local efficacy. Here we prepared cocrystals of this active principle with glutaric acid and so obtained a new crystalline solid representing a viable alternative to improve the physicochemical properties and thus the pharmaceutical behavior of the drug. Differential scanning calorimetry, X-ray powder diffraction, Fourier infrared spectroscopy, solid-state NMR, and scanning electron microscopy coupled to the energy-dispersive X-ray spectrometry were used to investigate the new solid-phase formation. DFT calculations at B3LYP/6-31G(d) level of theory, in the gas phase, including frequencies computation, provided a rationale for the interaction between loperamide hydrochloride and glutaric acid. The cocrystals showed improved water solubility in comparison with loperamide HCl, and the pharmaceutical formulation proposed was able to release the drug more rapidly in comparison with three reference commercial products when tested at neutral pH values.

Thermal, spectroscopic, and ab initio structural characterization of carprofen polymorphs.

Commercial and recrystallized polycrystalline samples of carprofen, a nonsteroidal anti-inflammatory drug, were studied by thermal, spectroscopic, and structural techniques. Our investigations demonstrated that recrystallized sample, stable at room temperature (RT), is a single polymorphic form of carprofen (polymorph I) that undergoes an isostructural polymorphic transformation by heating (polymorph II). Polymorph II remains then metastable at ambient conditions. Commercial sample is instead a mixture of polymorphs I and II. The thermodynamic relationships between the two polymorphs were determined through the construction of an energy/temperature diagram. The ab initio structural determination performed on synchrotron X-Ray powder diffraction patterns recorded at RT on both polymorphs allowed us to elucidate, for the first time, their crystal structure. Both crystallize in the monoclinic space group type P2(1) /c, and the unit cell similarity index and the volumetric isostructurality index indicate that the temperature-induced polymorphic transformation I → II is isostructural. Polymorphs I and II are conformational polymorphs, sharing a very similar hydrogen bond network, but with different conformation of the propanoic skeleton, which produces two different packing. The small conformational change agrees with the low value of transition enthalpy obtained by differential scanning calorimetry measurements and the small internal energy computed with density functional methods.