Assessment of Culture Systems to Produce Bacterial Cellulose with a Kombucha Consortium.

Bacterial cellulose (BC) is an emerging material for high-end applications due to its biocompatibility and physicochemical characteristics. However, the scale-up production of this material is still expensive, with the culture medium constituting one-third of the total cost. Herein, four different media (yeast nitrogen base, YNB; Murashige and Skoog, MSO; black tea; and NPK fertilizer solution) were compared while using sucrose as an additional carbon source. The yields of BC were best for YNB and fertilizer with 0.37 and 0.34 gBC/gC respectively. These two were then compared using glucose as a carbon source, with improvements in the production of 29% for the fertilizer, while only an 8% increase for YNB was seen; however, as the carbon concentration increased with a fixed N concentration, the yield was lower but the rate of production of BC increased. The obtained BC films were sanitized and showed low molecular weight and all the expected cellulose characteristic FT-IR bands while SEM showed nanofibers around 0.1 µm. Compared to traditional methods for lab-scale production, the use of the fertilizer and the consortium represent benefits compared to traditional lab-scale BC culture methods such as a competitive cost (two times lower) while posing resilience and tolerance to stress conditions given that it is produced by microbial communities and not with a single strain. Additionally, the low molecular weight of the films could be of interest for certain coating formulations.

Properties of APTES-Modified CNC Films.

Sulfated cellulose nanocrystals' (CNCs') facile aqueous dispersibility enables producing films, fibers, and other materials using only water as a solvent but prevents using sulfated CNCs in applications that require water immersion. We report that modifying CNCs with 3-aminopropyl-triethoxysilane (APTES) via a simple, single-pot reaction scheme dramatically improves the hydrolytic stability of CNC films. The effects of APTES modification on CNCs' properties were studied using attenuated total reflectance Fourier transform infrared spectroscopy, atomic force and optical microscopy, thermogravimetric analysis, dynamic light scattering, and ultimate analysis. Substituting a mere 12.6% of the CNCs' available hydroxyl groups with APTES dramatically increased the hydrolytic stability of shear cast films while only having minor impacts on their mechanical properties. In addition, quartz crystal microbalance with dissipation monitoring (QCMD) and multiparametric surface plasmon resonance (MP-SPR) studies showed that the CNC-APTES films also had a greater irreversible binding with carbofuran, a pesticide and emerging contaminant. These results highlight that APTES modification is a promising method for increasing the utility of sulfated CNCs in sensors, adsorbents, and other applications requiring water immersion.

Assessment of Bio-Based Materials as a Sustainable and Scalable Alternative for Detection of Plasmodium spp. (Haemospororida: Plasmodiidae) Sporozoites in Field Deployable Testing.

Malaria is responsible for over 435,000 deaths annually, mostly occurring in sub-Saharan Africa. Detecting Plasmodium spp. sporozoites (spzs) in the salivary glands of Anopheles (Diptera: Culicidae) vectors with circumsporozoite enzyme-linked immunosorbent assay (csELISA) is an important surveillance method. However, current technological advances are intellectual property and often require of distribution and highly trained users. The transition into paper-based rapid plataforms would allow for decentralization of survillance, especially in areas where it was virtually eliminated. The addition of bio-based materials have shown the potential to improve binding of target antigens, while being widely available. Here, we evaluate the use of chitosan and cellulose nanocrystals (CNC) as antibody carriers and substrate coatings on 96-well plates and on wax hydrophobized paper plates for the detection of Plasmodium falciparum (Pf), P. vivax VK210 (Pv210), and P. vivax VK247 (Pv247). To further improve the user-friendliness of the paper plates a quantitative photograph image-based color analysis was done. Interactions between the materials and the assay antibodies were studied by quartz crystal microbalance with dissipation monitoring (QCM-D). Overall, the addition of chitosan increased the interaction with antibodies and enhanced signaling in all tests. This work demonstrated that the adaptation of a PcsELISA shows potential as a cost-effective alternative assay platform easily adaptable in deployable testing sites that also showed reduction in reagent volumes by 80% and assay run time by seventh. While dipstick assays were previously developed, paper-based assays are a cost-effective and field-deployable alternative, reducing volumes of reagents that could be used in malaria control and elimination settings.

Antibody Immobilization on Sulfated Cellulose Nanocrystals.

Exploiting cellulose nanocrystals' high aspect ratio and tailorable surface for immunological biosensors has been hindered by the relatively limited research on using commonly available sulfated cellulose nanocrystals (CNCs) for antibody immobilization and by the low hydrolytic stability of dried assemblies produced from sulfated CNCs. Herein, we report a reaction scheme that enables both hydrolytic stability and antibody immobilization through 3-aminopropyl-triethoxysilane and glutaric anhydride chemistry. Immobilization was demonstrated using three model antibodies used in the detection of the cancer biomarkers: alpha-fetoprotein, prostate-specific antigen, and carcinoembryonic antigen. Thermogravimetric analysis coupled with Fourier-transform infrared spectroscopy provided evidence of CNC modification. Quartz crystal microbalance with dissipation monitoring was used to monitor binding during each step of the immobilization scheme as well as binding of the corresponding antigens. The general reaction scheme was tested using both aqueous CNC dispersions and CNC films. Film modification is slightly simpler as it avoids centrifugation and washing steps. However, modifying the dispersed CNCs provides access to their entire surface area and results in a greater capacity for antigen binding.

Comparison between nanocellulose-polyethylenimine composites synthesis methods towards multiple water pollutants removal: A review.

Nanocellulose/polyethylenimine composites have attracted growing attention due to their versatility as new materials for application in different fields. Water remediation is one of the traditional applications of these composites and their investigation as adsorbents for single water pollutants is well established. However, most water resources such as rivers, lakes, and even oceans contain complex mixtures of pollutants. Despite several recently published reviews on water purification technology, they only focused on these material as single pollutant removers and hardly mentioned their capacity to simultaneously recover multiple pollutants. Therefore, there is still a gap in the archived literature considering nanocellulose/polyethylenimine composites targeting water remediation with multiple water pollutants. In this review, methods for synthesizing such composites are classified and compared according to the mechanism of reactions, such as chemical crosslinking and physical adsorption, while outlining advantages and limitations. Then, the water pollutants mainly targeted by those composites are discussed in detail to expound the relationship between the synthesis method and the type and adsorption capacity. Finally, the last section presents challenges and opportunities of these nanocellulose/polyethylenimine composites as emerging sorbents for sustainable multiple water pollutants purification technologies. This review aims to lay out the basis for future developments of these composites for multiple water pollutants.

Understanding the current state-of-the-art of long-lasting insecticide nets and potential for sustainable alternatives.

Long-lasting insecticide-treated nets (LLINs) are widely distributed to communities where malaria is a major cause of mortality, especially to those under the age of 5 years-old. To protect people from this illness, LLINs provide physical and chemical barriers by containing insecticides within the matrix of the polymer fibers or on the surface. Synthetic polymers including polyethylene and polyester are common material choices for these nets, and pyrethroids, along with other additives, are the insecticides of choice for this application. Many studies have shown the effectiveness of these nets on the impact of malaria is highly significant, but there is a demand for more durable nets that last longer than only a few years as the available products are rated for 2-3 years of use. Improvements in this area would increase cost effectiveness, because better durability would reduce the frequency of manufacturing and worldwide shipping. Additionally, due to the plastic fibers, the waste can build quickly, damaging the environment. To deal with the sustainability and durability issues, biodegradable and renewable materials should be chosen as an alternative.

Delignified wood aerogels as scaffolds coated with an oriented chitosan-cyclodextrin co-polymer for removal of microcystin-LR.

Nano-porous aerogels are an advantageous approach to produce low-density materials with high surface area, particularly when using biobased materials. Frequently, most biobased aerogels are synthesized through a bottom-up approach, which requires high energy inputs to break and rebuild the raw materials, and for elimination of water. To curb this, this work focused on generating aerogels by a top-down approach through the delignification of a wood substrate while eliminating water by solvent exchange. To diversify the surface chemistry for use in water treatment, the delignified wood-nanowood-was coated with a chitosan-cyclodextrin co-polymer and tested in the capture of microcystin-LR. The generated nanowood structure had 75% porosity after coating, with up to 339% water swelling and an adsorption capacity of 0.12 mg g-1 of the microcystin. This top-down technique enables the generation of low-cost aerogels by reducing steps, using a biobased self-assembled coating with hydrophobic active sites, and avoiding costly energetic input.

Environmentally dependent adsorption of 2,4-dichlorophenol on cellulose-chitosan self-assembled composites.

With the increasing need for bio-based materials developed by environmentally friendly procedures, this work shows a green method to develop shape-controlled structures from cellulose dissolving pulp coated by chitosan. This material was then tested to adsorb a common and widespread pollutant, 2,4-dichlorophenol under different pH conditions (5.5 and 9). Herein it was noticed that the adsorption only occurred in acidic pH (5.5) where electrostatic interaction drove the adsorption, demonstrating the potential to tune the response under desired conditions only. The adsorption was successful in the hydrogel structure with an adsorption capacity of 905 ± 71 mg/g from a solution with 16.6 ppm; furthermore, adsorption was also possible with dried hydrogel structures, presenting a maximum of adsorption of 646 ± 50 mg/g in a similar 16.6 ppm solution. Finally, adsorbent regeneration was successfully tested for both, dry (rewetted) and never-dried states, showing improved adsorption after regeneration in the case of the never dried hydrogel structures.

Surface Interactions between Bacterial Nanocellulose and B-Complex Vitamins.

The interactions between films of bacterial nanocellulose (BNC) and B complex vitamins were studied using a Quartz Crystal Microbalance with Dissipation monitoring (QCM-D). Thin films of BNC were generated in situ by QCM-D, followed by real-time measurements of the vitamin adsorption. The desorption of vitamins was induced by rinsing the system using phosphate buffers at a pH of 2 and 6.5, emulating gastric conditions. Changes in frequency (which are proportional to changes in adsorbed mass, ∆m) detected by QCM-D were used to determine the amounts of vitamin adsorbed and released from the BNC film. Additionally, changes in dissipation (∆D) were proven to be useful in identifying the effects of the pH in both pristine cellulose films and films with vitamin pre-adsorbed, following its changes during release. The effects of pH on the morphology of the vitamin-BNC surfaces were also monitored by changes in rugosity from images obtained by atomic force microscopy (AFM). Based on this data, we propose a model for the binding phenomena, with the contraction on the relaxation of the cellulose film depending on pH, resulting in an efficient vitamin delivery process.

Cellulose-Cyclodextrin Co-Polymer for the Removal of Cyanotoxins on Water Sources.

With increasing global water temperatures and nutrient runoff in recent decades, the blooming season of algae lasts longer, resulting in toxin concentrations that exceed safe limits for human consumption and for recreational use. From the different toxins, microcystin-LR has been reported as the main cyanotoxin related to liver cancer, and consequently its abundance in water is constantly monitored. In this work, we report a methodology for decorating cellulose nanofibrils with ß-cyclodextrin or with poly(ß-cyclodextrin) which were tested for the recovery of microcystin from synthetic water. The adsorption was followed by Quartz Crystal Microbalance with Dissipation monitoring (QCM-D), allowing for real-time monitoring of the adsorption behavior. A maximum recovery of 196 mg/g was obtained with the modified by cyclodextrin. Characterization of the modified substrate was confirmed with Fourier Transform Infrared Spectroscopy (FT-IR), X-ray Photoelectron Spectroscopy (XPS), Thermogravimetric Analysis (TGA), and Atomic Force Microscopy (AFM).