Process Optimization and Mechanism Study for Sulfur Recovery from High-Silica Phosphogypsum via Carbothermal Reduction Smelting.

Phosphogypsum produced from wet-processed phosphoric acid mainly consists of calcium sulfate dihydrate, which is an important sulfur resource. The traditional sulfuric acid and cement process based on phosphogypsum suffers from unstable cement quality owing to impurities such as phosphorus and fluorine and kiln ringing caused by the low-melting phase. This study investigated sulfur recovery and value-added utilization of liquid slag from high-silica phosphogypsum via carbothermal reduction smelting. A phosphogypsum ingredient (PGI) system was constructed by adding appropriate amounts of silica, alumina, magnesium oxides, and iron oxides to meet the production requirements of slag wool. Carbothermal reduction smelting experiments suggested that the temperature and C/S molar ratio significantly affected the desulfurization rate and phase structure of the slag. More than 97.44 wt % of sulfur could be recovered with a C/S molar ratio of 0.5-0.8 at 1300 °C or above in the molten state, and the molten slag was an amorphous magnesium-calcium-aluminosilicate. The PGI desulfurization mechanism is discussed based on the phase transformation and slag microstructure evolution.

Intermediate Phase Suppression with Long Chain Diammonium Alkane for High Performance Wide-Bandgap and Tandem Perovskite Solar Cells.

Wide bandgap (WBG) perovskite can construct tandem cells with narrow bandgap solar cells by adjusting the band gap to overcome the Shockley-Queisser limitation of single junction perovskite solar cells (PSCs). However, WBG perovskites still suffer from severe nonradiative carrier recombination and large open-circuit voltage loss. Here, this work uses an in situ photoluminescence (PL) measurement to monitor the intermediate phase evolution and crystallization process via blade coating. This work reports a strategy to fabricate efficient and stable WBG perovskite solar cells through doping a long carbon chain molecule octane-1,8-diamine dihydroiodide (ODADI). It is found that ODADI doping not only suppresses intermediate phases but also promote the crystallization of perovskite and passivate defects in blade coated 1.67 eV WBG FA0.7 Cs0.25 MA0.05 Pb(I0.8 Br0.2 )3 perovskite films. As a result, the champion single junction inverted PSCs deliver the efficiencies of 22.06% and 19.63% for the active area of 0.07 and 1.02 cm2 , respectively, which are the highest power conversion efficiencies (PCEs) in WBG PSCs by blade coating. The unencapsulated device demonstrates excellent stability in air, which maintains its initial efficiency at the maximum power points under constant AM 1.5G illumination in open air for nearly 500 h. The resulting semitransparent WBG device delivers a high PCE of 20.06%, and the 4-terminal all-perovskite tandem device delivers a PCE of 28.35%.

Tailoring Perovskite Surface Potential and Chelation Advances Efficient Solar Cells.

Modifying perovskite surface using various organic ammonium halide cations has proven to be an effective approach for enhancing the overall performance of perovskite solar cells. Nevertheless, the impact of the structural symmetry of these ammonium halide cations on perovskite interface termination has remained uncertain. Here, this work investigates the influence of symmetry on the performance of the devices, using molecules based on symmetrical bis(2-chloroethyl)ammonium cation (B(CE)A+ ) and asymmetrical 2-chloroethylammonium cation (CEA+ ) as interface layers between the perovskite and hole transport layer. These results reveal that the symmetrical B(CE)A+ cations lead to a more homogeneous surface potential and more comprehensive chelation with uncoordinated Pb2+ compared to the asymmetrical cations, resulting in a more favorable energy band alignment and strengthened defect healing. This strategy, leveraging the spatial geometrical symmetry of the interface cations, promotes hole carrier extraction between functional layers and reduces nonradiative recombination on the perovskite surface. Consequently, perovskite solar cells processed with the symmetrical B(CE)A+ cations achieve a power conversion efficiency (PCE) of 25.60% and retain ≈91% of their initial PCE after 500 h of maximum power point operation. This work highlights the significant benefits of utilizing structurally symmetrical cations in promoting the performance and stability of perovskite solar cells.

Mixed tin-lead perovskites with balanced crystallization and oxidation barrier for all-perovskite tandem solar cells.

Mixed tin-lead perovskite solar cells have driven a lot of passion for research because of their vital role in all-perovskite tandem solar cells, which hold the potential for achieving higher efficiencies compared to single-junction counterparts. However, the pronounced disparity in crystallization processes between tin-based perovskites and lead-based perovskites, coupled with the easy Sn2+ oxidation, has long been a dominant factor contributing to high defect densities. In this study, we propose a multidimensional strategy to achieve efficient tin-lead perovskite solar cells by employing a functional N-(carboxypheny)guanidine hydrochloride molecule. The tailored N-(carboxypheny)guanidine hydrochloride molecule plays a pivotal role in manipulating the crystallization and grain growth of tin-lead perovskites, while also serving as a preservative to effectively inhibit Sn2+ oxidation, owing to the strong binding between N-(carboxypheny)guanidine hydrochloride and tin (II) iodide and the elevated energy barriers for oxidation. Consequently, single-junction tin-lead cells exhibit a stabilized power conversion efficiency of 23.11% and can maintain 97.45% of their initial value even after 3500 h of shelf storage in an inert atmosphere without encapsulation. We further integrate tin-lead perovskites into two-terminal monolithic all-perovskite tandem cells, delivering a certified efficiency of 27.35%.

Research progress on the catalytic and thermal decomposition of ammonium dinitramide (ADN).

Ammonium dinitramide (NH4N(NO3)2, ADN) is regarded as a promising oxidizer due to its low signature and high specific impulse. Generally, ADN undergoes exothermic decomposition above 140 °C accompanied by the byproduct of ammonium nitrate (AN). The inevitable endothermic decomposition of AN decreases the overall heat release, and so there is a need to develop efficient catalysts to guide ADN decomposition along desired pathways with a lower decomposition temperature and higher heat release. A suitable catalyst should be able to withstand the harsh conditions in a thruster to achieve a stable thrust force, which poses a huge obstacle for manufacturing a stable and active catalyst. This review gives a comprehensive summary of the thermal and catalytic decomposition pathways of ADN for the first time, which is expected to deepen the understanding of its reaction mechanism and provide useful guidance for designing prospective catalysts toward efficient ADN decomposition.

Regulating Crystal Orientation via Ligand Anchoring Enables Efficient Wide-Bandgap Perovskite Solar Cells and Tandems.

Wide-bandgap (WBG) perovskite solar cells have attracted considerable interest for their potential applications in tandem solar cells. However, the predominant obstacles impeding their widespread adoption are substantial open-circuit voltage (VOC ) deficit and severe photo-induced halide segregation. To tackle these challenges, a crystal orientation regulation strategy by introducing dodecyl-benzene-sulfonic-acid as an additive in perovskite precursors is proposed. This method significantly promotes the desired crystal orientation, passivates defects, and mitigates photo-induced halide phase segregation in perovskite films, leading to substantially reduced nonradiative recombination, minimized VOC deficits, and enhanced operational stability of the devices. The resulting 1.66 eV bandgap methylamine-free perovskite solar cells achieve a remarkable power conversion efficiency (PCE) of 22.40% (certified at 21.97%), with the smallest VOC deficit recorded at 0.39 V. Furthermore, the fabricated semitransparent WBG devices exhibit a competitive PCE of 20.13%. Consequently, four-terminal tandem cells comprising WBG perovskite top cells and 1.25 eV bandgap perovskite bottom cells showcase an impressive PCE of 28.06% (stabilized 27.92%), demonstrating great potential for efficient multijunction tandem solar cell applications.

Aspartate all-in-one doping strategy enables efficient all-perovskite tandems.

All-perovskite tandem solar cells hold great promise in surpassing the Shockley-Queisser limit for single-junction solar cells1-3. However, the practical use of these cells is currently hampered by the subpar performance and stability issues associated with mixed tin-lead (Sn-Pb) narrow-bandgap perovskite subcells in all-perovskite tandems4-7. In this study, we focus on the narrow-bandgap subcells and develop an all-in-one doping strategy for them. We introduce aspartate hydrochloride (AspCl) into both the bottom poly(3,4-ethylene dioxythiophene)-poly(styrene sulfonate) and bulk perovskite layers, followed by another AspCl posttreatment. We show that a single AspCl additive can effectively passivate defects, reduce Sn4+ impurities and shift the Fermi energy level. Additionally, the strong molecular bonding of AspCl-Sn/Pb iodide and AspCl-AspCl can strengthen the structure and thereby improve the stability of Sn-Pb perovskites. Ultimately, the implementation of AspCl doping in Sn-Pb perovskite solar cells yielded power conversion efficiencies of 22.46% for single-junction cells and 27.84% (27.62% stabilized and 27.34% certified) for tandems with 95% retention after being stored in an N2-filled glovebox for 2,000 h. These results suggest that all-in-one AspCl doping is a favourable strategy for enhancing the efficiency and stability of single-junction Sn-Pb perovskite solar cells and their tandems.

Extra- and intranuclear heat perception and triggering mechanisms in plants.

The escalating impact of global warming on crop yield and quality poses a significant threat to future food supplies. Breeding heat-resistant crop varieties holds promise, but necessitates a deeper understanding of the molecular mechanisms underlying plant heat tolerance. Recent studies have shed light on the initial events of heat perception in plants. In this review, we provide a comprehensive summary of the recent progress made in unraveling the mechanisms of heat perception and response in plants. Calcium ion (Ca2+), hydrogen peroxide (H2O2), and nitric oxide (NO) have emerged as key participants in heat perception. Furthermore, we discuss the potential roles of the NAC transcription factor NTL3, thermo-tolerance 3.1 (TT3.1), and Target of temperature 3 (TOT3) as thermosensors associated with the plasma membrane. Additionally, we explore the involvement of cytoplasmic HISTONE DEACETYLASE 9 (HDA9), mRNA encoding the phytochrome-interacting factor 7 (PIF7), and chloroplasts in mediating heat perception. This review also highlights the role of intranuclear transcriptional condensates formed by phytochrome B (phyB), EARLY FLOWERING 3 (ELF3), and guanylate-binding protein (GBP)-like GTPase 3 (GBPL3) in heat perception. Finally, we raise the unresolved questions in the field of heat perception that require further investigation in the future.

Photosynthesis Response and Transcriptional Analysis: Dissecting the Role of SlHB8 in Regulating Drought Resistance in Tomato Plants.

Deciphering drought resistance in crops is crucial for enhancing water productivity. Previous studies have highlighted the significant role of the transcription factor SlHB8 in regulating developmental processes in tomato plants but its involvement in drought resistance remains unclear. Here, gene overexpression (SlHB8-OE) and gene knockout (slhb8) tomato plants were utilized to study the role of SlHB8 in regulating drought resistance. Our findings showed that slhb8 plants exhibited a robust resistant phenotype under drought stress conditions. The stomata of slhb8 tomato leaves displayed significant closure, effectively mitigating the adverse effects of drought stress on photosynthetic efficiency. The slhb8 plants exhibited a decrease in oxidative damage and a substantial increase in antioxidant enzyme activity. Moreover, slhb8 effectively alleviated the degree of photoinhibition and chloroplast damage caused by drought stress. SlHB8 regulates the expression of numerous genes related to photosynthesis (such as SlPSAN, SlPSAL, SlPSBP, and SlTIC62) and stress signal transduction (such as SlCIPK25, SlABA4, and SlJA2) in response to drought stress. Additionally, slhb8 plants exhibited enhanced water absorption capacity and upregulated expression of several aquaporin genes including SlPIP1;3, SlPIP2;6, SlTIP3;1, SlNIP1;2, and SlXIP1;1. Collectively, our findings suggest that SlHB8 plays a negative regulatory role in the drought resistance of tomato plants.

Efficient Narrow-Bandgap Mixed Tin-Lead Perovskite Solar Cells via Natural Tin Oxide Doping.

Narrow-bandgap (NBG) mixed tin/lead-based (Sn-Pb) perovskite solar cells (PSCs) have attracted extensive attention for use in tandem solar cells. However, they are still plagued by serious carrier recombination due to inferior film properties resulting from the alloying of Sn with Pb elements, which leads to p-type self-doping behaviors. This work reports an effective tin oxide (SnOx ) doping strategy to produce high-quality Sn-Pb perovskite films for utilization in efficient single-junction and tandem PSCs. SnOx can be naturally oxidized from tin diiodide raw powders and successfully incorporated into Sn-Pb perovskite films. Consequently, Sn-Pb perovskite films doped with SnOx exhibit dramatically improved morphology, crystallization, absorption, and more interestingly, upward-shifted Fermi levels. The resulting narrow-bandgap Sn-Pb PSCs with natural SnOx doping have considerably reduced carrier recombination, therefore delivering a maximum power conversion efficiency (PCE) of 22.16% for single-junction cells and a remarkable PCE of 26.01% (with a steady-state efficiency of 25.33%) for two-terminal all-perovskite tandem cells. This work introduces a facile doping strategy for the manufacture of efficient single-junction narrow-bandgap PSCs and their tandem solar cells.

Antimony Potassium Tartrate Stabilizes Wide-Bandgap Perovskites for Inverted 4-T All-Perovskite Tandem Solar Cells with Efficiencies over 26.

Wide-bandgap (WBG) perovskites have been attracting much attention because of their immense potential as a front light-absorber for tandem solar cells. However, WBG perovskite solar cells (PSCs) generally exhibit undesired large open-circuit voltage (VOC) loss due to light-induced phase segregation and severe non-radiative recombination loss. Herein, antimony potassium tartrate (APTA) is added to perovskite precursor as a multifunctional additive that not only coordinates with unbonded lead but also inhibits the migration of halogen in perovskite, which results in suppressed non-radiative recombination, inhibited phase segregation and better band energy alignment. Therefore, a APTA auxiliary WBG PSC with a champion photoelectric conversion efficiency of 20.35% and less hysteresis is presented. They maintain 80% of their initial efficiencies under 100 mW cm-2 white light illumination in nitrogen after 1,000 h. Furthermore, by combining a semi-transparent WBG perovskite front cell with a narrow-bandgap tin-lead PSC, a perovskite/perovskite four-terminal tandem solar cell with an efficiency over 26% is achieved. Our work provides a feasible approach for the fabrication of efficient tandem solar cells.

Intermediate Phase Engineering with 2,2-Azodi(2-Methylbutyronitrile) for Efficient and Stable Perovskite Solar Cells.

Sequential deposition has been widely employed to modulate the crystallization of perovskite solar cells because it can avoid the formation of nucleation centers and even initial crystallization in the precursor solution. However, challenges remain in overcoming the incomplete and random transformation of PbI2 films with organic ammonium salts. Herein, a unique intermediate phase engineering strategy has been developed by simultaneously introducing 2,2-azodi(2-methylbutyronitrile) (AMBN) to both PbI2 and ammonium salt solutions to regulate perovskite crystallization. AMBN not only coordinates with PbI2 to form a favorably mesoporous PbI2 film due to the coordination between Pb2+ and the cyano group (C≡N), but also suppresses the vigorous activity of FA+ ions by interacting with FAI, leading to the full PbI2 transformation with the preferred orientation. Therefore, perovskites with favorable facet orientations are obtained, and the defects are largely suppressed owing to the passivation of uncoordinated Pb2+ and FA+ . As a result, a champion power conversion efficiency over 25% with a stabilized efficiency of 24.8% is achieved. Moreover, the device exhibits an improved operational stability, retaining 96% of initial power conversion efficiency under 1000 h continuous white-light illumination with an intensity of 100 mW cm-2 at ≈55 °C in N2 atmosphere.

The SlHB8 acts as a negative regulator in tapetum development and pollen wall formation in Tomato.

Pollen development is crucial for the fruit setting process of tomatoes, but the underlying regulatory mechanism remains to be elucidated. Here, we report the isolation of one HD-Zip III family transcription factor, SlHB8, whose expression levels decreased as pollen development progressed. SlHB8 knockout using CRISPR/Cas9 increased pollen activity, subsequently inducing fruit setting, whereas overexpression displayed opposite phenotypes. Overexpression lines under control of the 35 s and p2A11 promoters revealed that SlHB8 reduced pollen activity by affecting early pollen development. Transmission electron microscopy and TUNEL analyses showed that SlHB8 accelerated tapetum degradation, leading to collapsed and infertile pollen without an intine and an abnormal exine. RNA-seq analysis of tomato anthers at the tetrad stage showed that SlHB8 positively regulates SPL/NZZ expression and the tapetum programmed cell death conserved genetic pathway DYT1-TDF1-AMS-MYB80 as well as other genes related to tapetum and pollen wall development. In addition, DNA affinity purification sequencing, electrophoretic mobility shift assay, yeast one-hybrid assay and dual-luciferase assay revealed SlHB8 directly activated the expression of genes related to pollen wall development. The study findings demonstrate that SlHB8 is involved in tapetum development and degradation and plays an important role in anther development.

Identification of DELLA Genes and Key Stage for GA Sensitivity in Bolting and Flowering of Flowering Chinese Cabbage.

Flowering Chinese cabbage (Brassica campestris L. ssp. chinensis var. utilis Tsen et Lee) is an important and extensively cultivated vegetable in south China, and its stalk development is mainly regulated by gibberellin (GA). DELLA proteins negatively regulate GA signal transduction and may play an important role in determining bolting and flowering. Nevertheless, no systematic study of the DELLA gene family has been undertaken in flowering Chinese cabbage. In the present study, we found that the two-true-leaf spraying of gibberellin A3 (GA3) did not promote bolting but did promote flowering, whereas the three-true-leaf spraying of GA3 promoted both bolting and flowering. In addition, we identified five DELLA genes in flowering Chinese cabbage. All five proteins contained DELLA, VHYNP, VHIID, and SAW conserved domains. Protein-protein interaction results showed that in the presence of GA3, all five DELLA proteins interacted with BcGID1b (GA-INSENSITIVE DWARF 1b) but not with BcGID1a (GA-INSENSITIVE DWARF 1a) or BcGID1c (GA-INSENSITIVE DWARF 1c). Their expression analysis showed that the DELLA genes exhibited tissue-specific expression, and their reversible expression profiles responded to exogenous GA3 depending on the treatment stage. We also found that the DELLA genes showed distinct expression patterns in the two varieties of flowering Chinese cabbage. BcRGL1 may play a major role in the early bud differentiation process of different varieties, affecting bolting and flowering. Taken together, these results provide a theoretical basis for further dissecting the DELLA regulatory mechanism in the bolting and flowering of flowering Chinese cabbage.

Genome-Wide Identification and Expression Analysis of MADS-Box Family Genes in Litchi (Litchi chinensis Sonn.) and Their Involvement in Floral Sex Determination.

Litchi possesses unique flower morphology and adaptive reproduction strategies. Although previous attention has been intensively devoted to the mechanisms underlying its floral induction, the molecular basis of flower sex determination remains largely unknown. MADS-box genes are promising candidates for this due to their significant roles in various aspects of inflorescence and flower organogenesis. Here, we present a detailed overview of phylogeny and expression profiles of 101 MADS-box genes that were identified in litchi. These LcMADSs are unevenly located across the 15 chromosomes and can be divided into type I and type II genes. Fifty type I MADS-box genes are subdivided into Mα, Mß and Mγ subgroups, while fifty-one type II LcMADSs consist of 37 MIKCC -type and 14 MIKC *-type genes. Promoters of both types of LcMADS genes contain mainly ABA and MeJA response elements. Tissue-specific and development-related expression analysis reveal that LcMADS51 could be positively involved in litchi carpel formation, while six MADS-box genes, including LcMADS42/46/47/75/93/100, play a possible role in stamen development. GA is positively involved in the sex determination of litchi flowers by regulating the expression of LcMADS51 (LcSTK). However, JA down-regulates the expression of floral organ identity genes, suggesting a negative role in litchi flower development.

Genome-wide identification, phylogeny analysis, expression profiling, and determination of protein-protein interactions of the LEUNIG gene family members in tomato.

Members of the LEUNIG gene family have recently emerged as key players in gene repression, affecting several developmental mechanisms in plants, especially flower development. LEUNIG proteins function via recruiting adaptor SEUSS proteins. Nevertheless, no systematic studies on the LEUNIG and SEUSS gene families have been undertaken in tomato (Solanum lycopersicum, a fleshy fruit-bearing model plant, belonging to the Solanaceae family). Here, we present the results of a genome-wide analysis of tomato LEUNIG and SEUSS genes. In our study, we identified three SlLUG and four SlSEU genes. All three SlLUG full-length proteins contained the LEUNIG canonical domains (LUFS and two WD40 repeats), and the four full-length SlSEU genes contained the Lim-binding domain. All the members of the SlLUG and SlSEU family proteins were localized to the nucleus. All the SlSEU and SlLUG genes were detected in the tomato tissues tested. Expression analysis showed that the SlLUGs and SlSEUs exhibited tissue-specific expression, and that they responded to exogenous plant hormone and stress treatment. Protein-protein interaction analysis showed that only SlLUGs, but not SlSEUs, interacted with SlYABBY. Only a weak interaction between SlLUG1 and SlSEU3 was observed among all the SlLUG and SlSEU proteins. Taken together, these findings may help elucidate the roles played by SlLUG and SlSEU family members in plant growth and development.

Transcriptomic analysis of the regulation of stalk development in flowering Chinese cabbage (Brassica campestris) by RNA sequencing.

Flowering Chinese cabbage is a stalk vegetable whose quality and yield are directly related to stalk development. However, no comprehensive investigations on stalk development have been performed. To address this issue, the present study used RNA sequencing to investigate transcriptional regulation at three key stages (seedling, bolting, and flowering) of stalk development in flowering Chinese cabbage. Anatomical analysis revealed that cell division was the main mode of stalk thickening and elongation at all key stages. Among the 35,327 genes expressed in shoot apices, 34,448 were annotated and 879 were identified as novel transcripts. We identified 11,514 differentially expressed genes (DEGs) among the three stages of stalk development. Functional analysis revealed that these DEGs were significantly enriched in 'ribosome' and 'plant hormone signal transduction' pathways and were involved in hormone signal transduction, cell cycle progression, and the regulation of flowering time. The roles of these genes in stalk development were explored, and a putative gene-regulation network for the stalk flowering time was established. These findings provide insight into the molecular mechanisms of stalk development in flowering Chinese cabbage that provides a new theoretical basis for stalk vegetable breeding.

Catalytically Active Rh Sub-Nanoclusters on TiO2 for CO Oxidation at Cryogenic Temperatures.

The discovery that gold catalysts could be active for CO oxidation at cryogenic temperatures has ignited much excitement in nanocatalysis. Whether the alternative Pt group metal (PGM) catalysts can exhibit such high performance is an interesting research issue. So far, no PGM catalyst shows activity for CO oxidation at cryogenic temperatures. In this work, we report a sub-nano Rh/TiO2 catalyst that can completely convert CO at 223 K. This catalyst exhibits at least three orders of magnitude higher turnover frequency (TOF) than the best Rh-based catalysts and comparable to the well-known Au/TiO2 for CO oxidation. The specific size range of 0.4-0.8 nm Rh clusters is critical to the facile activation of O2 over the Rh-TiO2 interface in a form of Rh-O-O-Ti (superoxide). This superoxide is ready to react with the CO adsorbed on TiO2 sites at cryogenic temperatures.