Electrical and Mechanical Characterisation of Poly(ethylene)oxide-Polysulfone Blend for Composite Structural Lithium Batteries.

In this work, a blend of PEO, polysulfone (PSF), and lithium bis(trifluoromethanesulfonyl)imide (LiTFSi) was prepared at different PEO-PSf weight ratios (70-30, 80-20, and 90-10) and ethylene oxide to lithium (EO/Li) ratios (16/1, 20/1, 30/1, and 50/1). The samples were characterised using FT-IR, DSC, and XRD. Young's modulus and tensile strength were evaluated at room temperature with micro-tensile testing. The ionic conductivity was measured between 5 °C and 45 °C through electrochemical impedance spectroscopy (EIS). The samples with a ratio of PEO and PSf equal to 70-30 and EO/Li ratio equal to 16/1 have the highest conductivity (1.91 × 10-4 S/cm) at 25 °C, while the PEO-PSf 80-20 EO/Li = 50/1 have the highest averaged Young's modulus of about 1.5 GPa at 25 °C. The configuration with a good balance between electrical and mechanical properties is the PEO-PSf 70-30 EO/Li = 30/1, which has a conductivity of 1.17 × 10-4 S/cm and a Young's modulus of 800 MPa, both measured at 25 °C. It was also found that increasing the EO/Li ratio to 16/1 dramatically affects the mechanical properties of the samples with them showing extreme embrittlement.

Hollow Silica Nano and Micro Spheres with Polystyrene Templating: A Mini-Review.

Synthesis of monodisperse hollow silica nanospheres, especially using a hard template route, has been shown to be successful, but a high yield is needed for this strategy to be used on an industrial scale. On the other hand, there is a research gap in the synthesis of hollow silica microspheres due to the popularity and easiness of the synthesis of silica nanospheres despite the larger spheres being beneficial in some fields. In this review, current trends in producing hollow silica nanospheres using hard templates, especially polystyrene, are briefly presented. Soft templates have also been used to make highly polydisperse hollow silica spheres, and complex designs have improved polydispersity. The effect of the main parameters on the coating is presented here to provide a basic understanding of the interactions between the silica and template surface in the absence or presence of surfactants. Surface charge, surface modification, parameters in the sol-gel method and interaction between the silica and templates need to be further improved to have a uniform coating and better control over the size, dispersity, wall thickness and porosity. As larger organic templates will have lower surface energy, the efficiency of the micro sphere synthesis needs to be improved. Control over the physical structure of hollow silica spheres will open up many opportunities for them to be extensively used in fields ranging from waste removal to energy storage.

Oxidation Protective Hybrid Coating for Thermoelectric Materials.

Two commercial hybrid coatings, cured at temperatures lower than 300 °C, were successfully used to protect magnesium silicide stannide and zinc-doped tetrahedrite thermoelectrics. The oxidation rate of magnesium silicide at 500 °C in air was substantially reduced after 120 h with the application of the solvent-based coating and a slight increase in power factor was observed. The water-based coating was effective in preventing an increase in electrical resistivity for a coated tethtraedrite, preserving its power factor after 48 h at 350 °C.

Effect of the Processing Route on the Thermoelectric Performance of Nanostructured CuPb18SbTe20.

The quaternary AgPb18SbTe20 compound (abbreviated as LAST) is a prominent thermoelectric material with good performance. Endotaxially embedded nanoscale Ag-rich precipitates contribute significantly to decreased lattice thermal conductivity (κlatt) in LAST alloys. In this work, Ag in LAST alloys was completely replaced by the more economically available Cu. Herein, we conscientiously investigated the different routes of synthesizing CuPb18SbTe20 after vacuum-sealed-tube melt processing, including (i) slow cooling of the melt, (ii) quenching and annealing, and consolidation by (iii) spark plasma sintering (SPS) and also (iv) by the state-of-the-art flash SPS. Irrespective of the method of synthesis, the electrical (σ) and thermal (κtot) conductivities of the CuPb18SbTe20 samples were akin to those of LAST alloys. Both the flash-SPSed and slow-cooled CuPb18SbTe20 samples with nanoscale dislocations and Cu-rich nanoprecipitates exhibited an ultralow κlatt ∼ 0.58 W/m·K at 723 K, comparable with that of its Ag counterpart, regardless of the differences in the size of the precipitates, type of precipitate-matrix interfaces, and other nanoscopic architectures. The sample processed by flash SPS manifested higher figure of merit ( zT ∼ 0.9 at 723 K) because of better optimization and a trade-off between the transport properties by decreasing the carrier concentration and κlatt without degrading the carrier mobility. In spite of their comparable σ and κtot, zT of the Cu samples is low compared to that of the Ag samples because of their contrasting thermopower values. First-principles calculations attribute this variation in the Seebeck coefficient to dwindling of the energy gap (from 0.1 to 0.02 eV) between the valence and conduction bands in MPb18SbTe20 (M = Cu or Ag) when Cu replaces Ag.

Effect of Heat Treatment on the Properties of Wood-Derived Biocarbon Structures.

Wood-derived porous graphitic biocarbons with hierarchical structures were obtained by high-temperature (2200⁻2400 °C) non-catalytic graphitization, and their mechanical, electrical and thermal properties are reported for the first time. Compared to amorphous biocarbon produced at 1000 °C, the graphitized biocarbon-2200 °C and biocarbon-2400 °C exhibited increased compressive strength by ~38% (~36 MPa), increased electrical conductivity by ~8 fold (~29 S/cm), and increased thermal conductivity by ~5 fold (~9.5 W/(m·K) at 25 °C). The increase of duration time at 2200 °C contributed to increased thermal conductivity by ~12%, while the increase of temperature from 2200 to 2400 °C did not change their thermal conductivity, indicating that 2200 °C is sufficient for non-catalytic graphitization of wood-derived biocarbon.

Data-Driven Design of Ecofriendly Thermoelectric High-Entropy Sulfides.

High-entropy compounds with compositional complexity can be designed as new thermoelectric materials. Here a data-driven model was developed, which chose suitable elements to reduce the enthalpy of formation and hence to increase the chance of single phase formation. Using this model, two high-entropy sulfides were designed, metallic Cu5SnMgGeZnS9 and semiconducting Cu3SnMgInZnS7. They were then successfully fabricated as single-phase dense ceramics with homogeneously distributed cations, and their phase stability and atomic local structures were investigated using density functional theory calculations. Finally, a zT value of 0.58 at 773 K was obtained for Cu5Sn1.2MgGeZnS9, where additional Sn was used to tune the carrier concentration. This work provides a simple approach to find new high-entropy functional materials in the largely unexplored multielement chemical space.