The relation between impact strength and flexural strength of dental materials.

AIM: The aim of this study was to investigate whether there is a relation between impact strength and flexural strength of different composite and ceramic materials used in dental restorations. MATERIALS AND METHODS: The three-point-bending test was used to determine the flexural strength and flexural modulus, and the Dynstat impact test was used to determine the impact strength of different composite and ceramic dental materials. The relation between the flexural strength and impact strength was mathematically investigated and a three-dimensional finite element analysis model of the impact test set-up was created to verify these results. RESULTS: We found a relation between the impact strength, adU, the flexural strength, σ, and the flexural modulus, E, which can be represented by the formula: adU=λDK(σ2/E), where λDK is a constant dependent on the test set-up. CONCLUSION: The obtained impact strength of materials is specific to the test set-up and dependent on the geometric configuration of the test set-up and the specimen thickness. The clinical significance of this investigation is that roughness and fatigue have far more influence on the impact strength than the flexure strength.

Surface treatments of a glass-fiber reinforced composite: Effect on the adhesion to a composite resin.

PURPOSE: To compare the effect of different surface treatments (pre-treatments and bonding agents) on the bond strength between glass-fiber post and composite resin, and the topographic alterations of the treated post surface. METHODS: Thirty-six glass-fiber blocks (12mm×10mm×8mm) were specifically manufactured for this study and randomly assigned into 12 groups considering two factors: 'pre-treatments' (-cleaning with 70% alcohol; air-abrasion with silica-coated aluminum oxide particles; 35% hydrogen peroxide) and type of 'bonding agent' (no bonding agent; application of Monobond Plus; RelyX Ceramic Primer; Single Bond Universal). After that, 6 cylindrical templates (1mm high×1mm Ø) were fixed on each block, filled with composite resin (n=18) and light-cured. Specimens were stored under 37°C for 24h and microshear tests (wire loop Ø=0.2mm) were performed. Topographic, roughness and failure analyses were also performed. RESULTS: Different surface pre-treatments led to different topographic and roughness alterations; a higher surface alteration was noted after silica particles air-abrasion, while a slight surface alteration in the hydrogen peroxide group and a smooth pattern were observed in the cleaning group. The factors 'pre-treatments' (p<0.05), 'bonding agent' (p<0.05) and their interaction (p<0.05) influenced the bond strength. Silica coating, apart from bonding agent application, or Single Bond Universal application without pre-treatment promoted the highest bond values. The main failure type was adhesive at the resin-post interface. CONCLUSIONS: In terms of pre-treatments, silica coating promotes the best bonding performance, but pre-treatments can be dispensable when applying Single Bond Universal.

Mechanical reliability, fatigue strength and survival analysis of new polycrystalline translucent zirconia ceramics for monolithic restorations.

This study characterized the mechanical properties (static and under fatigue), the crystalline microstructure (monoclinic - m, tetragonal - t and cubic - c phase contents) and the surface topography of three yttrium-stabilized zirconia (YSZ) materials with different translucent properties, before and after aging in an autoclave (low temperature degradation). Disc-shaped specimens were produced from second generation (Katana ML/HT - high-translucent) and third generations (Katana STML - super-translucent and UTML - ultra-translucent) YSZ ceramics (Kuraray Noritake Dental Inc.), following ISO 6872-2015 guidelines for biaxial flexural strength testing (final dimensions: 15 mm in diameter and 1.2 ±â€¯0.2 mm in thickness), and then subjected to the respective tests and analyses. ML was mainly composed of tetragonal crystals, while STML and UTML presented cubic content. Aging increased the monoclinic content for ML and did not affect STML and UTML. Topographical analysis highlights different grain sizes on the ceramic surface (UTML > STML > ML) and aging had no effect on this outcome. Weibull analysis showed the highest characteristic strength for ML both before and after aging, and statistically similar Weibull moduli for all groups. ML material also obtained the highest survival rates (ML > STML > UTML) for both fatigue strength and number of cycles to failure. All fractures originated from surface defects on the tensile side. Third generation zirconia (Katana STML and UTML) are fully stabilized materials (with tetragonal and cubic crystals), being totally inert to the autoclave aging, and presented lower mechanical properties than the second-generation zirconia (Katana ML - metastable zirconia).