Reactivity of nitrogen atoms from Zif-8 structure deposited over Ti3C2 MXene in the electrochemical nitrogen reduction reaction.

The electrochemical nitrogen reduction reaction (NRR) to produce NH3 is the most efficient, eco-friendly and cost-effective alternative to the Haber-Bosch process. It is crucial to investigate and develop electrocatalysts selective for NH3 synthesis. In recent studies, the Ti3C2 MXene has emerged as a highly promising electrocatalyst for the NRR process. In this work, we explore the effect of Zif-8 addition over MXene sheets in order to control the rate of hydrogen evolution reaction (HER). Despite the better result obtained for Zif-8@Ti3C2 (3.0 µg NH3 gcat-1 h-1 at -0.55 V/RHE), the ammonia produced when using Zif-8@Ti3C2 as cathode material is shown to be originated from nitrogen atoms contained in the Zif-8 structure instead of those of N2. The results shed light to the need to fully understand the N2 electroreduction process over N-containing electrocatalysts.

Low temperature in situ immobilization of nanoscale fcc and hcp polymorphic nickel particles in polymer-derived Si-C-O-N(H) to promote electrocatalytic water oxidation in alkaline media.

We synthesized nickel (Ni) nanoparticles (NPs) in a high specific surface area (SSA) p-block element-containing inorganic compound prepared via the polymer-derived ceramics (PDC) route to dispatch the obtained nanocomposite towards oxygen evolution reaction (OER). The in situ formation of Ni NPs in an amorphous silicon carboxynitride (Si-C-O-N(H)) matrix is allowed by the reactive blending of a polysilazane, NiCl2 and DMF followed by the subsequent thermolysis of the Ni : organosilicon polymer coordination complex at a temperature as low as 500 °C in flowing argon. The final nanocomposite displays a BET SSA as high as 311 m2 g-1 while the structure of the NPs corresponds to face-centred cubic (fcc) Ni along with interstitial-atom free (IAF) hexagonal close-packed (hcp) Ni as revealed by XRD. A closer look into the compound through FEG-SEM microscopy confirms the formation of pure metallic Ni, while HR-TEM imaging reveals the occurrence of Ni particles featuring a fcc phase and surrounded by carbon layers; thus, forming core-shell structures, along with Ni NPs in an IAF hcp phase. By considering that this newly synthesized material contains only Ni without doping (e.g., Fe) with a low mass loading (0.15 mg cm-2), it shows promising OER performances with an overpotential as low as 360 mV at 10 mA cm-2 according to the high SSA matrix, the presence of the IAF hcp Ni NPs and the development of core-shell structures. Given the simplicity, the flexibility, and the low cost of the proposed synthesis approach, this work opens the doors towards a new family of very active and stable high SSA nanocomposites made by the PDC route containing well dispersed and accessible non-noble transition metals for electrocatalysis applications.

Preparation and Electrochemical Properties of NiCo2 O4 Nanospinels Supported on Graphene Derivatives as Earth-Abundant Oxygen Bifunctional Catalysts.

This work reports on the facile synthesis and characterisation of a non-precious-metal bifunctional catalyst for oxygen reduction and evolution reactions (ORR and OER). A few-layer reduced graphene oxide-supported NiCo2 O4 catalyst is prepared using a rapid and easy two-step method of synthesis. It consists of the solvothermal poyl(vinylpyrrolidone)-assisted assembly of metal complexes onto few-layer graphene followed by a calcination step aiming at converting metal complexes into the spinel phase. Using this synthesis approach, the most active material demonstrates an outstanding activity towards the OER and ORR, making it one of the best bifunctional catalysts of these reactions ever reported. This composite catalyst exhibits improved bifunctional behaviour with a low reversibility criterion of 746 mV. The ORR process follows a four-electron pathway and the hydroxyl selectivity is higher than those with pure reduced graphene oxide or NiCo2 O4 materials, showing the synergistic effect between the two phases. Moreover, the high activity of this composite catalyst is confirmed by comparing its performance with those obtained on other cobaltite catalysts prepared using a different synthesis method, or those obtained using a different graphene-based support.

Yttrium oxide/gadolinium oxide-modified platinum nanoparticles as cathodes for the oxygen reduction reaction.

Rare-earth-element (Y, Gd) modified Pt nanoparticles (NPs) supported on a carbon substrate (Vulcan XC-72) are synthesized via a water-in-oil chemical route. In both cases, X-ray diffraction (XRD) measurements show the non-formation of an alloyed material. Photoemission spectroscopy (XPS) results reveal that Y and Gd are oxidized. Additionally, no evidence of an electronic modification of Pt can be brought to light. Transmission electron microscopy (TEM) studies indicate that Pt-Y(2)O(3) and Pt-Gd(2)O(3) particles are well dispersed on the substrate-and that their average particle sizes are smaller than the Pt-NP sizes. The catalytic activity of the Pt-Y(2)O(3)/C and Pt-Gd(2)O(3)/C catalysts towards the oxygen reduction reaction (ORR) is studied in a 0.5 M H(2)SO(4) electrolyte. The surface and mass specific activities of the Pt-Y(2)O(3)/C catalyst towards the ORR at 0.9 V (vs. the reversible hydrogen electrode, RHE) are (54.3±1.2) µA cm(-2)(Pt) and MA=(23.1±0.5) mA mg(-1)(Pt), respectively. These values are 1.3-, and 1.6-fold higher than the values obtained with a Pt/C catalyst. Although the as-prepared Pt-Gd(2)O(3)/C catalyst has a lower catalytic activity for the ORR compared to Pt/C, the heat-treated sample shows a surface specific activity of about (53.0±0.7) µA cm(-2) Pt , and a mass specific activity (MA) of about (18.2±0.5) mA mg(-1) Pt at 0.9 V (vs. RHE). The enhancement of the ORR kinetics on the Pt-Y(2)O(3)/C and heat-treated Pt-Gd(2)O(3)/C catalysts could be associated with the formation of platinum NPs presenting modified surface properties.

Electronic modification of Pt via Ti and Se as tolerant cathodes in air-breathing methanol microfluidic fuel cells.

We reported herein on the use of tolerant cathode catalysts such as carbon supported Pt(x)Ti(y) and/or Pt(x)Se(y) nanomaterials in an air-breathing methanol microfluidic fuel cell. In order to show the improvement of mixed-reactant fuel cell (MRFC) performances obtained with the developed tolerant catalysts, a classical Pt/C nanomaterial was used for comparison. Using 5 M methanol concentration in a situation where the fuel crossover is 100% (MRFC-mixed reactant fuel cell application), the maximum power density of the fuel cell with a Pt/C cathodic catalyst decreased by 80% in comparison with what is observed in the laminar flow fuel cell (LFFC) configuration. With Pt(x)Ti(y)/C and Pt(x)Se(y)/C cathode nanomaterials, the performance loss was only 55% and 20%, respectively. The evaluation of the tolerant cathode catalysts in an air-breathing microfluidic fuel cell suggests the development of a novel nanometric system that will not be size restricted. These interesting results are the consequence of the high methanol tolerance of these advanced electrocatalysts via surface electronic modification of Pt. Herein we used X-ray photoelectron and in situ FTIR spectroscopies to investigate the origin of the high methanol tolerance on modified Pt catalysts.

Structural and electrochemical studies of Au-Pt nanoalloys.

Carbon supported Au-Pt catalysts with different bimetallic compositions were prepared by water-in-oil (w/o) micro-emulsions. Carbon Vulcan XC-72R was added during the synthesis of particles in order to obtain good dispersion. Structural characterization was performed using XRD (X-ray diffraction) at wide angles, WAXS (wide-angle X-ray scattering) which showed that Pt-Au particles exhibited alloy properties in samples with high gold-content, and a segregation effect for those with low gold-content. Electrochemical characterization allowed estimation of the surface composition of Pt-Au alloys. These experiments have been confirmed by XRD data. Moreover, HRTEM (high resolution transmission electron microscopy) and XEDS (X-ray energy dispersive spectroscopy) characterization further confirmed the electrochemical results and XRD data. CO stripping experiments have shown an increasing bonding energy between CO and platinum with the gold content in the nanoalloys.