Generative deep learning approaches for the design of dental restorations: A narrative review.

OBJECTIVES: This study aims to explore and discuss recent advancements in tooth reconstruction utilizing deep learning (DL) techniques. A review on new DL methodologies in partial and full tooth reconstruction is conducted. DATA/SOURCES: PubMed, Google Scholar, and IEEE Xplore databases were searched for articles from 2003 to 2023. STUDY SELECTION: The review includes 9 articles published from 2018 to 2023. The selected articles showcase novel DL approaches for tooth reconstruction, while those concentrating solely on the application or review of DL methods are excluded. The review shows that data is acquired via intraoral scans or laboratory scans of dental plaster models. Common data representations are depth maps, point clouds, and voxelized point clouds. Reconstructions focus on single teeth, using data from adjacent teeth or the entire jaw. Some articles include antagonist teeth data and features like occlusal grooves and gap distance. Primary network architectures include Generative Adversarial Networks (GANs) and Transformers. Compared to conventional digital methods, DL-based tooth reconstruction reports error rates approximately two times lower. CONCLUSIONS: Generative DL models analyze dental datasets to reconstruct missing teeth by extracting insights into patterns and structures. Through specialized application, these models reconstruct morphologically and functionally sound dental structures, leveraging information from the existing teeth. The reported advancements facilitate the feasibility of DL-based dental crown reconstruction. Beyond GANs and Transformers with point clouds or voxels, recent studies indicate promising outcomes with diffusion-based architectures and innovative data representations like wavelets for 3D shape completion and inference problems. CLINICAL SIGNIFICANCE: Generative network architectures employed in the analysis and reconstruction of dental structures demonstrate notable proficiency. The enhanced accuracy and efficiency of DL-based frameworks hold the potential to enhance clinical outcomes and increase patient satisfaction. The reduced reconstruction times and diminished requirement for manual intervention may lead to cost savings and improved accessibility of dental services.

The Obese Taste Bud study: Objectives and study design.

AIMS: Taste modifies eating behaviour, impacting body weight and potentially obesity development. The Obese Taste Bud (OTB) Study is a prospective cohort study launched in 2020 at the University of Leipzig Obesity Centre in cooperation with the HI-MAG Institute. OTB will test the hypothesis that taste cell homeostasis and taste perception are linked to obesity. Here, we provide the study design, data collection process and baseline characteristics. MATERIALS AND METHODS: Participants presenting overweight, obesity or normal weight undergo taste and smell tests, anthropometric, and taste bud density (TBD) assessment on Day 1. Information on physical and mental health, eating behaviour, physical activity, and dental hygiene are obtained, while biomaterial (saliva, tongue swap, blood) is collected in the fasted state. Further blood samples are taken during a glucose tolerance test. A stool sample is collected at home prior to Day 2, on which a taste bud biopsy follows dental examination. A subsample undergoes functional magnetic resonance imaging while exposed to eating-related cognitive tasks. Follow-up investigations after conventional weight loss interventions and bariatric surgery will be included. RESULTS: Initial results show that glycated haemoglobin levels and age are negatively associated with TBD, while an unfavourable metabolic profile, current dieting, and vegan diet are related to taste perception. Olfactory function negatively correlates with age and high-density lipoprotein cholesterol. CONCLUSION: Initial findings suggest that metabolic alterations are relevant for taste and smell function and TBD. By combining omics data from collected biomaterial with physiological, metabolic and psychological data related to taste perception and eating behaviour, the OTB study aims to strengthen our understanding of taste perception in obesity.

Aging processes in dental thermoplastics - Thermoanalytical investigations and effects on Vickers as well as Martens hardness.

OBJECTIVE: The influence of various aging protocols, representing and accelerating influences present in the dental context, on possible changes in the microstructure and mechanical properties of thermoplastics was investigated. In order to minimize the complexity of the systems, first pure polymers and then later the equivalent dental polymeric materials were analyzed. MATERIALS AND METHODS: Pure polymers (Poly(methyl methacrylate) - PMMA, Polyoxymethylene homopolymer - POM-H, Polyether ether ketone - PEEK, Nylon 12 - PA12, Polypropylene - PP) were analyzed before as well as after applying different aging protocols relevant to the oral environment (ethanol, thermocycling, alkaline and acidic setting) by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). The thermoanalytical parameters used were glass transition temperature (Tg), melting peak and crystallization peak temperature (Tpm, Tpc) and decomposition behavior. In a second step selected commercially available dental products (Telio CAD - PMMAD, Zirlux Acetal - POMD, Juvora Natural Dental Disc - PEEKD) aged by the protocol that previously showed strong effects were examined and additionally tested for changes in their Vickers and Martens hardness by Mann-Whitney-U test. RESULTS: The combinations of pure polymers and viable aging protocols analyzed within this study were identified via TGA or DSC as PA12 & thermocycling, POM-H & denture cleanser/lactic acid/ethanol, PP & lactic acid. The dental polymeric materials PMMAD and POMD due to aging in lactic acid showed slight but significantly (p < 0.01) reduced Vickers and partly Martens hardness. PEEK showed the greatest material resistance within this study.

Influence of cement type, excess removal, and polishing on the cement joint.

OBJECTIVES: To compare marginal gap width and depth with different cementation systems, excess removal, and after polishing. METHOD AND MATERIALS: In total, 80 composite crowns were milled, divided into ten groups, and cemented on identical artificial teeth. Eight crowns per group were fixed with (i) zinc phosphate cement (ZnOPh), (ii) glass-ionomer cement (GIC), (iii) resin-reinforced glass-ionomer cement (GIC mod), (iv) dual-curing adhesive composite (Comp dual), or (v) dual-curing self-adhesive composite (Comp SE dual). Excess removal was performed with a scaler after brief light-cure (tack-cure), final light-cure, during rubber or gel phase or by wiping with foam pellet. Curing was completed in chemical, dark cure, or light-curing modus. The specimens were polished and stored in water (37°C). The margins were digitized using a 3D laser-scanning microscope (VK-X100 series, Keyence). The width and the depth of the marginal gap were measured at 10 points between the crown margin and the preparation margin. RESULTS: The width after excess removal varied between 65.1 ± 15.7 µm (Comp dual, wipe, with polishing) and 208.6 ± 266.7 µm (Comp SE dual, dark cure, without polishing). The depth varied between 29.8 ± 22.2 µm (Comp dual, wipe, with polishing) and 89.5 ± 45.2 µm (Comp SE dual, dark cure, without polishing). The impact on gap width and depth was detected for fixation material, excess removal, and polishing. CONCLUSION: The gap depth and width depend on the luting material and the mode of access removal. Polishing can improve the gap quality, especially for GIC and resin-based systems.

Attachment of Respiratory Pathogens and Candida to Denture Base Materials-A Pilot Study.

Denture prostheses are an ideal and extensive reservoir for microorganisms to attach to their surfaces. The aim of the study was to elucidate interactions between materials for the fabrication of denture bases and the attachment of microorganisms, focusing on respiratory pathogens and Candida species. Specimens (6 mm × 1 mm) with a standardized surface roughness (Sa = 0.1 µm) were prepared from heat-pressed polymethyl methacrylate (PMMA), CAD/CAM-processed PMMA, and CAD/CAM-processed polyether ether ketone (PEEK). The specimens were randomly placed in the vestibular areas of complete upper dentures in seven patients and were removed either after 24 h without any oral hygiene measures or after a period of four weeks. The microorganisms adherent to the surface of the specimens were cultivated and subsequently analyzed using mass spectrometry (MALDI-TOF). The means and standard deviations were calculated, and the data were analyzed using a two-way analysis of variance (ANOVA) and Tukey post-hoc test where appropriate (α = 0.05). There was a significant increase (p ≤ 0.004) in the total bacterial counts (CFU/mL) between the first (24 h) and the second (four weeks) measurements. Regarding quantitative microbiological analyses, no significant differences between the various materials were identified. Respiratory microorganisms were detected in all samples at both measurement time points, with a large variance between different patients. Only after four weeks, Candida species were identified on all materials but not in all participants. Candida species and respiratory microorganisms accumulate on various denture base resins. While no significant differences were identified between the materials, there was a tendency towards a more pronounced accumulation of microorganisms on conventionally processed PMMA.

Influence of aging of PEEK attachment inserts on the pull-off force of implant-retained overdentures - A laboratory study.

OBJECTIVES: The aim of the current study is to investigate the influence of mechanical stress as well as cleaning agents on the performance of various polyether ether ketone (PEEK) inserts for implant-retained overdentures (IOD). MATERIALS AND METHODS: Three different standard PEEK inserts were subjected to rapid artificial aging through storage in chemical denture cleaning agents (acetic acid, sodium hypochlorite, or sparkling denture cleaner) as well as demineralized water. The pre-aged PEEK inserts were then placed in unilateral IOD and subjected to 200,000 chewing loads (5 kg ~ 50 N), with 5000 thermal cycles (5/55°C), and 1100 removal/insertion cycles (vertical movement 2 mm). RESULTS: For all the PEEK inserts, the retention forces decreased significantly with an increasing number of mechanical load cycles and after exposure to all the cleaning agents. PEEK inserts aged by exposure to chemical cleaning agents showed a significantly higher decline in retention force than the inserts stored in water. Confocal laser scanning microscopy indicated that the decline in retention force might be caused by wear on the internal insert surface in contact with the patrix. CONCLUSIONS: Within the limitations of this study, it can be concluded that the application of chemical cleaning agents accelerates the decline in the retention forces of PEEK retentive inserts in IODs.

Aging and Fracture Resistance of Implant-Supported Molar Crowns with a CAD/CAM Resin Composite Veneer Structure.

Chipping of implant-supported molar crowns (iSCs) is a frequently reported complication. This study aimed to investigate the in-vitro aging and fracture resistance of iSCs with a CAD/CAM resin composite veneer structure fabricated with the Rapid Layer Technology (RLT) approach. Eight iSCs per group were fabricated by using two different CAD/CAM resin composites (Shofu Block HC: SH; Grandio blocs: GB) for veneer structures, and zirconia (ZrO2), polyetheretherketone (PEEK), and cobalt-chromium (CoCr; control) as framework materials. The surfaces to be bonded were sandblasted, cleaned in an ultrasonic bath, and a coupling agent was applied. A self-adhesive resin luting composite was used to adhesively lute the veneer structures to the frameworks. The crowns were semi-permanently cemented to the abutments. After storage in deionized water, iSCs were loaded in a chewing simulator (TCML, 10,000 thermal cycles 5 °C to 55 °C for 20 s, 1.2 million, loading force 50 N). Four ZrO2 and one CoCr crown did not survive the TCML. The fracture force was determined after 24 h storage in deionized water and yielded values of ≥974 N. Lowest fracture forces were yielded in the PEEK-SH group in comparison to CoCr or ZrO2 groups (p ≤ 0.031). For identical framework materials, no significant influence of the veneering material was observed. All PEEK-GB frameworks fractured, and chipping occurred for ZrO2-SH and all CoCr frameworks. PEEK-SH and ZrO2-GB presented both chipping and framework fractures. Within the limitations of this in-vitro study, the RLT with a CAD/CAM resin composite veneer structure might be a promising approach to veneer iSCs. Yet, the choice of the CAD/CAM resin composite and of the framework material determine the fracture resistance.

Digital Workflow in Oral Splint Manufacturing.

AIM: The digital workflow used to manufacture an adjusted oral splint will be demonstrated in a patient case. MATERIALS AND METHODS: A 25-year-old female patient presented for management of her bruxism. Therefore, an adjusted oral splint was manufactured. A computer-aided motion analysis of the patient was conducted (JMA Optic, Amann Girrbach) and full-arch scans of the maxilla and mandible, a biocopy of the maxilla with bite fork as well as buccal scans of the centric jaw relation (Primescan, Dentsply Sirona). The jaw relation was determined beforehand by ballistic closing on a chairside fabricated anterior jig. The digital construction of a Michigan splint took place in the laboratory. The design was nested and milled from a polymethyl methacrylate (PMMA)-containing blank (CLEARsplint Disc, Astron Dental Corporation). RESULT: The oral splint was inserted into the patient's mouth and checked to ensure a tensionfree fit. The static and dynamic contact relationship was checked. During the follow-up visit, the patient reported an improvement in tension in the masticatory muscles. CONCLUSION: The procedure described allows for an adjusted oral splint to be manufactured in a purely digital workflow.

Aging and fracture resistance of screw-retained implant-supported molar crowns fabricated from lithium disilicate containing virgilite.

Purpose To investigate aging and fracture resistance of screw-retained implant-supported single crowns (iSCs) fabricated from lithium disilicate containing virgilite (VLD). Materials and Methods iSCs were fabricated from VLD (CEREC Tessera, Dentsply Sirona) and lithium disilicate (control; n=8, e.max CAD, Ivoclar) and bonded to a Ti-base abutment. VLD crowns were luted either with (VLDc, n=8) or without (VLDw, n=8) a coupling agent. iSCs were cleaned, sterilized, and screw-retained on implants. Fracture force was determined after thermal cycling and mechanical loading (TCML). Results All crowns survived TCML. No significant differences in mean fracture forces were identified between VLDc 1583 N, VLDw 1694 N, and control 1797 N (P=0.639 ANOVA, P=1.000 Bonferroni). Conclusion Screw-retained iSCs fabricated from VLD provide acceptable stability, which is independent on the usage of a coupling agent for bonding to Ti-base abutments and sterilization. Int J Prosthodont 2023. doi: 10.11607/ijp.8369.

Long-term survival of monolithic tooth-supported lithium disilicate crowns fabricated using a chairside approach: 15-year results.

OBJECTIVES: To investigate the clinical performance of chairside fabricated tooth-supported posterior single crowns from lithium disilicate ceramic. MATERIALS AND METHODS: Thirty-four crowns (IPS e.max CAD, Ivoclar Vivadent, Schaan, Liechtenstein) were inserted between 2006 and 2007 and again evaluated after 15 years. Survival and success rates were calculated according to Kaplan-Meier, and the quality of the crowns was evaluated by using modified United States Public Health (USPHS) criteria. RESULTS: Twenty-two crowns were available for recall; six patients were defined as dropouts. The mean observation period was 15.2 years (± 0.2). Six failures occurred (1 technical/5 biological) resulting in a survival rate of 80.1%. The success rate was 64.2%. The roughness of the crowns increased (p = 0.021) and the majority of adhesive gaps were discolored (p = 0.001) in comparison to baseline. The color, tooth, and crown integrity remained stable over the follow-up period (p ≥ 0.317). CONCLUSION: The fabrication of tooth-supported lithium disilicate crowns using a chairside approach yielded acceptable long-term survival and success rates. Due to discoloration, the long-term use of dual-cure self-adhesive resin cements might result in unpleasing esthetic results. CLINICAL RELEVANCE: The performance of posterior lithium disilicate single crowns revealed excellent to good clinical quality and an acceptable number of events after 15 years of clinical service.

Retention force, translucency, and microstructural properties of translucent temporary luting cements: An in vitro study.

The aim of the study was to investigate the retention behaviour (pull-off force include adhesive remnant index = ARI) as well as translucency of various temporary luting cements and use microstructure elucidation methods to formulate explanatory approaches to their mode of action. The retention force of the temporary luting cements Provicol QM Plus (P+), Provicol QM Aesthetic (Pae), Bifix Temp (BiT), and as a reference a glass ionomer cement Meron (M) with a direct (Structur 3/S3) or an indirect (Structure CAD/SCAD) resin-based composite restauration was investigated after accelerated aging (thermocycling). Additional investigation of the physical properties was performed regarding to translucency and surface free energy. The microstructure was evaluated by X-ray diffraction, thermogravimetric analysis, differential scanning calorimetry and micro X-ray computed tomography. All tested temporary luting cements showed different pull-off forces in the range between 3.0 and 16.8 N in combination with S3 or SCAD after thermocycling. Only BiT with S3 showed pull-off forces of 129.2 N and complete retention on the restoration (ARI = 0), which was significant (p < .001) to all other samples. High translucency (BiT > Pae > M > P+) was observed for materials with lower crystalline content and low residual mass (usally resulting from higher organic content). M showed the highest surface free energy with a predominantly polar fraction, while BiT had a predominantly dispersive fraction. The highest porosity was observed in the coronal region of the restoration. The results suggest that translucency of temporary luting cements can be increased with higher organic and lower cryristall content. All combinations of cements and temporary restorations (direct/indirect; with the exception of BiT/S3) showed pull-off forces below 17 N (equivalent to a weight force of ∼1.7 kg), which allows manual detachment of the restoration by the dentist.

Influence of the Application Time of Silane for the Bonding Performance between Feldspar or Lithium Disilicate Ceramics and Luting Resin Composites.

A correct silanization time is essential for successful surface functionalization and sufficient bonding to dental ceramics. The shear bond strength (SBS) of lithium disilicate (LDS) and feldspar (FSC) ceramics and luting resin composite was investigated with respect to different silanization times, taking into account the physical properties of the individual surfaces. The SBS test was performed with a universal testing machine, and the fracture surfaces were evaluated by stereomicroscopy. The surface roughness of the prepared specimens was analyzed after etching. Changes in surface properties due to surface functionalization were evaluated by surface free energy (SFE) via contact angle measurement. Fourier transform infrared spectroscopy (FTIR) was used to determine the chemical binding. The roughness and SBS of the control group (no silane, etched) were higher for FSC than for LDS. Regarding the SFE, the dispersive fraction increased and the polar fraction decreased after silanization. FTIR confirmed the presence of silane on the surfaces. The SBS of LDS showed a significant increase from 5 to 15 s, depending on the silane and luting resin composite. For FSC, cohesive failure was observed for all samples. For LDS specimens, a silane application time of 15 to 60 s is recommended. Based on clinical conditions, no difference between the silanization times was observed for FSC specimens, indicating that etching alone produces sufficient bonding.

In-vitro performance of subtractively and additively manufactured resin-based molar crowns.

PURPOSE: To compare the in-vitro performance and wear behavior of additively or subtractively fabricated resin-based composite molar crowns for temporary and permanent application. MATERIALS AND METHODS: Identical molar crowns (n = 8 per group) were manufactured from materials for temporary or permanent application (3x temporary additive fabrication, 3x additive permanent fabrication, 1x temporary subtractive fabrication, 1x permanent subtractive fabrication). All crowns were adhesively bonded (Calibra Universal, Dentsply Sirona, USA) on standardized resin-based composite molars (FDI 46, P Pro temporary Crown & Bridge). Thermal cycling and mechanical loading (2 × 3000 × 5°C/55 °C, 2min, H20 dist., 1.2 × 106 force 50N) were performed and fracture force was determined (v = 1 mm/min, Z010, Zwick, Germany). Mean wear, maximum wear, and roughness were investigated on polished (P1200) specimens (n = 8 per group, d = 8 mm) in a pin-on-block test (50N; 120000 cycles; 1.6Hz; H2O). Statistics were performed by using one-way ANOVA, Bonferroni post-hoc-tests, and Pearson-correlation (α = 0.05). RESULTS: All crowns survived TCML without failures. Fracture forces ranged from 1362.4 ± 182.4N to 2354.1 ± 373.3N for the additive temporary crowns, from 1680.4.4 ± 525.1N to 2601.6 ± 403.7N for the additive permanent crowns, and reached values of 2988.5 ± 604.7N for subtractive temporary crowns and 3092.0 ± 307.6 N for subtractive permanent crowns. Significant (p < 0.001) differences were identified between the various additively manufactured systems, but not for the subtractively fabricated systems (p = 0.673). Mean wear of the additive temporary crowns ranged between 114.5 ± 25.8 µm and 163.8 ± 21.4 µm without significant differences (p = 0.061). Mean wear of the additive permanent crowns ranged between 120.0 ± 27.5 µm and 171.3 ± 31.8 µm with significant differences (p = 0.004). No statistically significant differences were identified between temporary and permanent subtractively manufactured specimens, with mean wear ranging between 140.5 ± 51.1 µm and 176.6 ± 26.8 µm (p = 0.673). Maximum wear of additive temporary specimens ranged between 221.4.5 ± 53.3 µm and 322.1 ± 50.6 µm; significant differences were identified between the groups (p = 0.016). Maximum wear of additive permanent specimens ranged between 246.3 ± 47.3 µm and 337.4 ± 61.4 µm, and significant differences were identified between the groups (p = 0.006). Mean wear of the subtractive group (permanent and temporary) showed no differences in maximum wear from 277.9 ± 79.7.1 µm to 316.4 ± 58.1 µm (p = 0.288). Ra roughness ranged from 0.7 ± 0.2 µm to 3.6 ± 1.3 µm with significant differences (p < 0.001) and Rz reference between 65.9 ± 26.2 µm and 16.8 ± 6.3 µm. CONCLUSION: Temporary and permanent molar crowns provided at least acceptable in-vitro performance and fracture force for clinical mid-term application. Laboratory wear stability of the resin-based materials appeared sufficient, but should be verified under clinical conditions.

Bacterial Adhesion on Dental Polymers as a Function of Manufacturing Techniques.

The microbiological behavior of dental polymer materials is crucial to secure the clinical success of dental restorations. Here, the manufacturing process and the machining can play a decisive role. This study investigated the bacterial adhesion on dental polymers as a function of manufacturing techniques (additive/subtractive) and different polishing protocols. Specimens were made from polyaryletherketone (PEEK, PEKK, and AKP), resin-based CAD/CAM materials (composite and PMMA), and printed methacrylate (MA)-based materials. Surface roughness (Rz; Ra) was determined using a laser scanning microscope, and SFE/contact angles were measured using the sessile drop method. After salivary pellicle formation, in vitro biofilm formation was initiated by exposing the specimens to suspensions of Streptococcus mutans (S. mutans) and Streptococcus sanguinis (S. sanguinis). Adherent bacteria were quantified using a fluorometric assay. One-way ANOVA analysis found significant influences (p < 0.001) for the individual parameters (treatment and material) and their combinations for both types of bacteria. Stronger polishing led to significantly (p < 0.001) less adhesion of S. sanguinis (Pearson correlation PC = -0.240) and S. mutans (PC = -0.206). A highly significant (p = 0.010, PC = 0.135) correlation between S. sanguinis adhesion and Rz was identified. Post hoc analysis revealed significant higher bacterial adhesion for vertically printed MA specimens compared to horizontally printed specimens. Furthermore, significant higher adhesion of S. sanguinis on pressed PEEK was revealed comparing to the other manufacturing methods (milling, injection molding, and 3D printing). The milled PAEK samples showed similar bacterial adhesion. In general, the resin-based materials, composites, and PAEKs showed different bacterial adhesion. Fabrication methods were shown to play a critical role; the pressed PEEK showed the highest initial accumulations. Horizontal DLP fabrication reduced bacterial adhesion. Roughness < 10 µm or polishing appear to be essential for reducing bacterial adhesion.

The influence of different storage media on Vickers hardness and surface roughness of CAD/CAM resin composites.

INTRODUCTION: This study examined Vickers hardness as well as surface characteristics of different computer-aided design/computer-aided manufacturing (CAD/CAM) resin composites prior to and after storage in various media. MATERIALS AND METHODS: CAD/CAM resin composite blocks (Grandio Blocs (GB), Lava Ultimate (LU), Brilliant Crios (BC), Cerasmart (GC), Shofu Block HC (SB), Tetric CAD (TC), Luxacam Composite (LC); incl. different translucency variants) were prepared, polished and surface free energy was determined. The specimens were divided into four groups: dry conditions for 24 h (25 °C), demineralized water (37 °C), Pepsi Cola (37 °C) and 75% ethanol (37 °C). After seven and 28 days of storage, Vickers hardness was determined. Surface roughness was measured after the entire storage period. RESULTS AND DISCUSSION: Vickers hardness was in the range of about 150 HV for GB, around 115 HV for LU, and 80-100 HV for BC, GC, SB, TC and LC. Only minor differences (total: 50.2 (6.4)-56.2 (3.2) mN/m) in surface free energy could be detected. No relationship was observed between surface free energy and filler content. However, a correlation between filler content and Vickers hardness was evident. Artificial aging caused a decrease of Vickers hardness (up to -40 HV or 35%) depending on storage media, duration and material. The changes in surface texture after immersion in different media were below a value of ΔSa = 0.015 µm. CONCLUSION: Artificial aging of CAD/CAM resin composites leads to a significant decrease of Vickers hardness for most materials, while only small changes in surface roughness were identified.

Prevalence of temporomandibular disorders and bruxism in seniors.

BACKGROUND: Information on the prevalence of temporomandibular disorders (TMD) or possible/probable bruxism in seniors is heterogeneous and sparse. OBJECTIVES: To elucidate the prevalence of TMD and possible/probable bruxism in German adults aged 60 years and older. METHODS: Participants of the Interdisciplinary Longitudinal Study of Adult Development and Aging (ILSE) born between 1950-1952 (C1) and 1930-1932 (C2) were examined in 2014-2016 (fourth wave). The participants were surveyed and clinically examined by one calibrated examiner. Two questions of the Patient Health Questionnaire (PHQ) were utilised to evaluate self-reported bruxism. The clinical examination included signs of probable bruxism and the RDC/TMD examination protocol. RESULTS: Data from 191 participants were available. No RDC/TMD diagnosis was made in 83.2%. Of the participants, 15.2% received a single diagnosis and 1.6% multiple diagnoses that included disc displacements (9.4%) and degenerative joint diseases (8.9%). A total of 24.7% reported bruxism that included self-reported awake bruxism in 11.9% and sleep bruxism in 16.2%. Wear was clinically identified in 27.2% of the participants. No sex-related differences were observed. Significant differences were detected for probable bruxism between C1 (14.1%) and C2 (54.3%). CONCLUSION: In the German population aged 60 years and older, the prevalence of TMD is 16.8%. TMD is characterised by temporomandibular joint disorders, including disc displacements and degenerative joint disorders. Bruxism was observed in a quarter of the old population.

Influence of dental prophylaxis procedures on the tooth veneer interface in resin-based composite and polymer-infiltrated ceramic veneer restorations: an in vitro study.

OBJECTIVES: The aim of this study was to investigate the influence of dental prophylaxis cleaning procedures and artificial aging on veneers in human teeth. The external marginal and internal tooth veneer as well as the restoration surfaces were examined. MATERIAL AND METHODS: Thirty-two extracted premolars were restored with resin-based composite (RBC) and polymer-infiltrated ceramic network (PICN) veneers. Artificial aging by alternating thermocycling and subsequent prophylaxis procedure (glycine-based powder air polishing or ultrasonic scaling) was conducted for five consecutive cycles. The external marginal interface was examined by height profile measurements and the internal interface was investigated using micro X-ray computed tomography. In addition, the surface texture of the veneer surface was analyzed using confocal laser scanning microscopy. RESULTS: The application of both prophylaxis procedures resulted in a deepening of the marginal interface (10 µm ± 8 µm) for materials. Furthermore, the internal interface of PICN restorations showed marginal gaps after both treatments and artificial aging (16 µm ± 3 µm). In contrast to the RBC specimens, a significant increase in surface roughness was identified for PICN veneers after ultrasonic scaling. CONCLUSIONS: The marginal and internal interface regions in veneers fabricated from PICN and RBC were affected by prophylaxis procedures. Furthermore, it may result in increased veneer surface roughness, especially in PICN and after ultrasonic scaling, which might affect bioadhesion and longevity. CLINICAL RELEVANCE: After dental prophylaxis procedures, examination of the marginal and the internal interface as well as the veneer surface provides a precise insight into damage mechanisms and offers an assessment of longevity.

Intraoral Repair of Chipping Due to Cohesive Failure-Results of a Nationwide Survey Among Dentists in Germany.

PURPOSE: To survey the materials favored by dentists for intraoral repair of cohesive chipping. MATERIALS AND METHODS: From August 2019 to February 2020, dentists were surveyed to determine the frequency of cohesive chipping experienced within the last 3 months and to identify their preferred approaches for intraoral repair. RESULTS: Of the participants, 42.5% observed chipping (n = 506). Participants favored the application of roughening devices, silane, and composite resins. Self-etching glass-ceramic primers or hydrofluoric acid were used for ceramic etching. CONCLUSION: Dentists apply a variety of materials for intraoral repair of chipping, including materials that are not approved for intraoral use. Int J Prosthodont 2023;36:216-218. doi: 10.11607/ijp.7098.

TEGDMA-Functionalized Dicalcium Phosphate Dihydrate Resin-Based Composites Prevent Secondary Caries in an In Vitro Biofilm Model.

This study evaluated the efficacy of experimental TEGDMA-functionalized dicalcium phosphate dihydrate (T-DCPD) filler-based resin-based composites (RBC) in preventing caries lesions around the restoration margins (secondary caries, SC). Standardized Class-II cavities were made in sound molars with the cervical margin in dentin. Cavities were filled with a commercial resin-modified glass-ionomer cement (RMGIC) or experimental RBCs containing a bisGMA-TEGDMA resin blend and one of the following inorganic fractions: 60 wt.% Ba glass (RBC-0); 40 wt.% Ba glass and 20 wt.% T-DCPD (RBC-20); or 20 wt.% Ba glass and 40 wt.% T-DCPD (RBC-40). An open-system bioreactor produced Streptococcus mutans biofilm-driven SC. Specimens were scanned using micro-CT to evaluate demineralization depths. Scanning electron microscopy and energy-dispersive X-ray spectroscopy characterized the specimen surfaces, and antimicrobial activity, buffering effect, and ion uptake by the biofilms were also evaluated. ANOVA and Tukey's tests were applied at p < 0.05. RBC-0 and RBC-20 showed SC development in dentin, while RBC-40 and RMGIC significantly reduced the lesion depth at the restoration margin (p < 0.0001). Initial enamel demineralization could be observed only around the RBC-0 and RBC-20 restorations. Direct antibiofilm activity can explain SC reduction by RMGIC, whereas a buffering effect on the acidogenicity of biofilm can explain the behavior of RBC-40. Experimental RBC with CaP-releasing functionalized T-DCPD filler could prevent SC with the same efficacy as F-releasing materials.

Microbiological models for accelerated development of secondary caries in vitro.

OBJECTIVES: The current study aimed to compare the efficacy of two in vitro microbiological models based on open and closed systems designed to obtain secondary caries in an accelerated and reproducible way. METHODS: A conventional resin-based composite (RBC - Majesty ES-2; Kuraray, Japan) and a resin-modified glass-ionomer cement (RMGIC - Ionolux; VOCO, Germany) were used to restore standardized class II cavities (n = 4/tooth, cervical margin in dentin) in 16 human molars. The ability to produce secondary caries with Streptococcus mutans biofilms was tested using either an open-cycle or closed-cycle bioreactor (n = 8 specimens/model). Specimens were scanned before and after the biofilm exposure using micro-CT (Skyscan 1176, 9 µm resolution, 80 kV, 300 mA). Image reconstruction was performed, and demineralization depths (µm) were evaluated at the restoration margins and a distance of 1.0 mm. RESULTS: Dentin demineralization could be observed in all specimens, and enamel demineralization in 50% of the specimens. The open system bioreactor produced lesions with significantly higher overall demineralization depths (p < .001). However, demineralization depths at a 1.0 mm distance from the restoration margins showed no difference between open and closed systems or materials. In the open system, significantly lower demineralization depths were observed in proximity to RMGIC than RBC (p < .001), which was not significantly different in the closed system (p = .382). CONCLUSIONS: Both systems produced in vitro secondary caries in an accelerated way. However, the open-cycle bioreactor system confirmed the caries-protective activity exerted by the RMGIC material in contrast to the RBC, better simulating materials' clinical behavior. CLINICAL SIGNIFICANCE: The possibility of obtaining accelerated and reproducible secondary caries development in vitro is fundamental in testing the behavior of conventional and yet-to-come restorative dental materials. Such systems can provide faster outcomes regarding the performance of dental restorative materials compared to clinical studies, notwithstanding the importance of the latter.