"Micro-to-nano": Reengineering of jute for constructing cellulose nanofibers as a next-generation biomaterial.

Micro-to-nano transformation can make a material unique. This research uses jute microfiber to extract Holo and Alpha forms of cellulose, which are later attempted to electrospun into superfine nanofibers (NFs). Initial investigation of morphological, physicochemical, crystallographic, and thermal properties confirmed successful synthesis of Holo and Alpha-cellulose (H/A-cellulose). Afterwards, the electrospinnable concentration of H/A-cellulose was optimized and their bead-free ultrafine NFs in the range of 109-145 nm were fabricated. FTIR analysis confirmed the source composition in Holo and Alpha CNF with the partial formation of trifluoroacetyl esters. Alpha CNF exhibited better structural integrity despite the crystallinity and thermal stability deteriorated in both Holo and Alpha CNF. Both Holo and Alpha CNF exhibited adequate mechanical performance and liquid uptake properties. Alpha CNF showed better morphological stability in organic solvents and slower biodegradation than Holo CNF. Subsequent investigation revealed that both Holo and Alpha CNF didn't exhibit cytotoxic effects on COS-7 cells and above 90 % of cells were viable in contact with both CNF. Significant proliferation and attachment of COS-7 cells were noticed within 7 days of incubation with the prepared CNF. Our findings revealed that jute-extracted cellulose can be a viable and potential source for constructing cellulose-based advanced nano-biomaterials.

Electrospun composite nanofibers of deoxyribonucleic acid and polylactic acid for skincare applications.

The development of useful biomaterials has resulted in significant advances in various fields of science and technology. The demand for new biomaterial designs and manufacturing techniques continues to grow, with the goal of building a sustainable society. In this study, two types of DNA-cationic surfactant complexes were synthesized using commercially available deoxyribonucleic acid from herring sperm DNA (hsDNA, <50 bp) and deoxyribonucleic acid from salmon testes DNA (stDNA, ~2000 bp). The DNA-surfactant complexes were blended with a polylactic acid (PLA) biopolymer and electrospun to obtain nanofibers, and then copper nanoparticles were synthesized on nanofibrous webs. Scanning electron microscopic images showed that all nanofibers possessed uniform morphology. Interestingly, different diameters were observed depending on the base pairs in the DNA complex. Transmission electron microscopy showed uniform growth of copper nanoparticles on the nanofibers. Fourier-transform infrared spectroscopy spectra confirmed the uniform blending of both types of DNA complexes in PLA. Both stDNA- and hsDNA-derived nanofibers showed greater biocompatibility than native PLA nanofibers. Furthermore, they exerted significant antibacterial activity in the presence of copper nanoparticles. This study demonstrates that DNA is a potentially useful material to generate electrospun nanofibrous webs for use in biomedical sciences and technologies.

The Effect of Polymeric Nanofibers Used for 3D-Printed Scaffolds on Cellular Activity in Tissue Engineering: A Review.

Promising scaffolds for developing advanced tissue engineering architectures have emerged in recent years through the use of nanofibers and 3D printing technologies. Despite this, structural integrity and cell proliferation are highlighted as fundamental challenges for design scaffolds and future prospects. As a biomimetic scaffold, the nanofiber-reinforced hydrogels demonstrated a better compressive modulus and cell growth. Our review focuses on recent promising advances in the development of 3D-printed hydrogels containing polymeric nanofibers that can improve cell-material interaction in biomedical applications. Moreover, an effort has been made to induce studies with diverse types of scaffolds for various cells. Additionally, we discuss the challenges and future prospects of 3D-bioprinted reinforced hydrogels with nanofibers in the medical field, as well as high-performance bioinks.

Lignin-facilitated growth of Ag/CuNPs on surface-activated polyacryloamidoxime nanofibers for superior antibacterial activity with improved biocompatibility.

INTRODUCTION: Nanofibers are one of the role-playing innovations of nanotechnology. Their high surface-to-volume ratio allows them to be actively functionalized with a wide range of materials for a variety of applications. The functionalization of nanofibers with different metal nanoparticles (NPs) has been studied widely to fabricate antibacterial substrates to battle antibiotic-resistant bacteria. However, metal NPs show cytotoxicity to living cells, thereby restricting their application in biomedicine. OBJECTIVES: To minimize the cytotoxicity of NPs, biomacromolecule lignin was employed as both a reducing and capping agent to green synthesize silver (Ag) and copper (Cu) NPs on the surface of highly activated polyacryloamidoxime nanofibers. The activation of polyacrylonitrile (PAN) nanofibers via amidoximation was employed for enhanced loading of NPs to achieve superior antibacterial activity. METHODOLOGY: At first, electrospun PAN nanofibers (PANNM) were activated to produce polyacryloamidoxime nanofibers (AO-PANNM) by immersing PANNM in a solution of Hydroxylamine hydrochloride (HH) and Na2CO3 under controlled conditions. Later, Ag and Cu ions were loaded by immersing AO-PANNM in different molar concentrations of AgNO3 and CuSO4 solutions in a stepwise manner. The reduction of Ag and Cu ions into NPs to fabricate bimetal-coated PANNM (BM-PANNM) was carried out via alkali lignin at 37 °C for 3 h in a shaking incubator with ultrasonication every 1 h. RESULTS: AO-APNNM and BM-PANNM hold their nano-morphology except for some changes in fiber orientation. XRD analysis demonstrated the formation of Ag and CuNPs as evident from their respective spectral band. Maximum 8.46 ± 0.14 wt% and 0.98 ± 0.04 wt% Ag and Cu species were loaded on AO-PANNM, respectively as revealed by ICP spectrometric analysis. The hydrophobic PANNM turned into super hydrophilic, having WCA of 14 ± 3.32° after amidoximation which further reduced to 0° for BM-PANNM. However, the swelling ratio of PANNM reduced from 13.19 ± 0.18 g/g to 3.72 ± 0.20 g/g for AO-PANNM. Even at the third cycle test against S. aureus strains, 0.1Ag/Cu-PANNM, 0.3Ag/Cu-PANNM, and 0.5Ag/Cu-PANNM displayed bacterial reduction of 71.3 ± 1.64 %, 75.2 ± 1.91 %, and 77.24 ± 1.25 %, respectively. On 3rd cycle test against E. coli, above 82 % bacterial reduction was noticed for all BM-PANNM. Amidoximation increased COS-7 cell viability up to 82 %. The cell viability of 0.1Ag/Cu-PANNM, 0.3Ag/Cu-PANNM, and 0.5Ag/Cu-PANNM was found to be ∼68 %, ∼62, and 54 %, respectively. In LDH assay, almost no release of LDH was detected, suggesting the compatibility of the cell membrane in contact with BM-PANNM. The improved biocompatibility of BM-PANNM even at higher loading (%) of NPs must be ascribed to the controlled release of metal species in the early stage, antioxidant, and biocompatible lignin capping of NPs. CONCLUSIONS: BM-PANNM displayed superior antibacterial activity against E. coli and S. aureus bacterial strains and acceptable biocompatibility of COS-7 cells even at higher loading (%) of Ag/CuNPs. Our findings suggest that BM-PANNM can be used as a potential antibacterial wound dressing and other antibacterial applications where sustained antibacterial activity is needed.

Synthesized bioactive lignin nanoparticles/polycaprolactone nanofibers: A novel nanobiocomposite for bone tissue engineering.

The use of artificial biomaterial with enhanced bioactivity for osteostimulation is a major research concern at present days. In this research, antibacterial and osteostimulative core-shell lignin nanoparticles (LgNP) were synthesized from alkali lignin using tetrahydrofuran (THF) as solvent via a simultaneous pH and solvent shifting technology. Later, LgNP-loaded polycaprolactone (PCL) composite nanofibers were fabricated via the electrospinning technique. The addition of LgNP significantly increased the diameter of the nanofibers, ranging from 400 to 2200 nm. The addition of LgNP reduced the mechanical performance, crystallinity, and porosity of the nanofibers while improving surface wetting and swelling properties of the inherently hydrophobic PCL polymer. The prepared nanofibers showed excellent bactericidal efficacy against major bone infectious Gram-positive Staphylococcus aureus bacterial strains. The incorporation of LgNP imparted superior antioxidant activity and boosted the biodegradation process of the nanofibers. The deposition of biomineral apatite with platelet-like clustered protrusions having a Ca/P ratio of 1.67 was observed while incubating the scaffold in simulated body fluid. Based on the results of the LDH and WST-1 assay, it was demonstrated that the composite nanofibers are non-toxic to pre-osteoblastic cell line (MC3T3-E1) when they are placed in direct contact with the LgNP/PCL scaffold nanofibers. The MC3T3-E1 cells exhibited excellent proliferation and attachment on the prepared composite scaffold via filopodial and lamellipodial expansion with cell-secreted Ca deposition. According to the alkaline phosphatase activity test, LgNP/PCL nanofiber scaffolds significantly improved osteogenic differentiation of MC3T3-E1 cells compared to neat PCL nanofibers. Overall, our findings suggest that LgNP/PCL nanofiber scaffold could be a promising functional biomaterial for bone tissue engineering.

Antibacterial Activity of Molybdenum Oxide-Polyacrylonitrile Composite Membrane with Fast Silver Ion Reduction.

The development of hybrid composite antibacterial agents for wound dressing has garnered significant attention due to their remarkable antibacterial efficacy and their potential to mitigate microbial resistance. In this study, we present an approach to designing and fabricating wound dressing membranes, utilizing molybdenum oxide-polyacrylonitrile (MoO3/PAN) hybrid composites through electrospinning. Subsequently, we enhanced the membrane's effectiveness by introducing silver (Ag@MoO3/PAN) into the matrix via a rapid (within one min) green synthesis method under UV irradiation. Initially, we discuss the morphological characteristics and structural attributes of the resulting membranes. Subsequent investigations explore the antibacterial mechanisms of both MoO3 and Ag+, revealing that the incorporation of silver substantially enhanced antibacterial activity. Additionally, we elucidate the surface properties, noting that the introduction of silver increases the surface area of the composite membrane by 25.89% compared with the pristine MoO3/PAN membrane. Furthermore, we observe a 9% reduction in the water contact angle (WCA) for the Ag@MoO3/PAN membrane, indicating improved hydrophilicity. Finally, we analyze the release behavior of the Ag@MoO3/PAN membrane. Our findings demonstrate an initial burst release within the first 7 h, followed by a controlled and sustained release pattern over a period of 7 days.

Development of PVA-Psyllium Husk Meshes via Emulsion Electrospinning: Preparation, Characterization, and Antibacterial Activity.

In this study, polyvinyl alcohol (PVA) and psyllium husk (PSH)/D-limonene electrospun meshes were produced by emulsion electrospinning for use as substrates to prevent the growth of bacteria. D-limonene and modified microcrystalline cellulose (mMCC) were preferred as antibacterial agents. SEM micrographs showed that PVA-PSH electrospun mesh with a 4% amount of D-limonene has the best average fiber distribution with 298.38 ± 62.8 nm. Moreover, the fiber morphology disrupts with the addition of 6% D-limonene. FT-IR spectroscopy was used to analyze the chemical structure between matrix-antibacterial agents (mMCC and D-limonene). Although there were some partial physical interactions in the FT-IR spectrum, no chemical reactions were seen between the matrixes and the antibacterial agents. The thermal properties of the meshes were determined using thermal gravimetric analysis (TGA). The thermal stability of the samples increased with the addition of mMCC. Further, the PVA-PSH-mMCC mesh had the highest value of contact angle (81° ± 4.05). The antibacterial activity of functional meshes against Gram (-) (Escherichia coli, Pseudomonas aeruginosa) and Gram (+) bacteria (Staphylococcus aureus) was specified based on a zone inhibition test. PPMD6 meshes had the highest antibacterial results with 21 mm, 16 mm, and 15 mm against Escherichia coli, Staphylococcus aureus, and Pseudomonas aeruginosa, respectively. While increasing the amount of D-limonene enhanced the antibacterial activity, it significantly decreased the amount of release in cases of excess D-limonene amount. Due to good fiber morphology, the highest D-limonene release value (83.1%) was observed in PPMD4 functional meshes. The developed functional meshes can be utilized as wound dressing material based on our data.

Fabricating Antibacterial and Antioxidant Electrospun Hydrophilic Polyacrylonitrile Nanofibers Loaded with AgNPs by Lignin-Induced In-Situ Method.

Concerning the environmental hazards owing to the chemical-based synthesis of silver nanoparticles (AgNPs), this study aimed to investigate the possibility of synthesizing AgNPs on the surface polyacrylonitrile (PAN) nanofibers utilizing biomacromolecule lignin. SEM observations revealed that the average diameters of the produced nanofibers were slightly increased from ~512 nm to ~673 nm due to several factors like-swellings that happened during the salt treatment process, surface-bound lignin, and the presence of AgNPs. The presence of AgNPs was validated by transmission electron microscope (TEM) and X-ray photoelectron spectroscopy (XPS) analysis. The amount of synthesized AgNPs on PAN nanofibers was found to be dependent on both precursor silver salt and reductant lignin concentration. Fourier transform infrared-attenuated total reflectance (FTIR-ATR) spectra confirm the presence of lignin on PAN nanofibers. Although the X-ray diffraction pattern did not show any AgNPs band, the reduced intensity of the stabilized PAN characteristics bands at 2θ = 17.28° and 29.38° demonstrated some misalignment of PAN polymeric chains. The water contact angle (WCA) of hydrophobic PAN nanofibers was reduced from 112.6 ± 4.16° to 21.4 ± 5.03° for the maximum AgNPs coated specimen. The prepared membranes exhibited low thermal stability and good swelling capacity up to 20.1 ± 0.92 g/g and 18.05 ± 0.68 g/g in distilled water and 0.9 wt% NaCl solution, respectively. Coated lignin imparts antioxidant activity up to 78.37 ± 0.12% at 12 h of incubation. The resultant nanofibrous membranes showed a proportional increase in antibacterial efficacy with the rise in AgNPs loading against both Gram-positive S. aureus and Gram-negative E. coli bacterial strains by disc diffusion test (AATCC 147-1998). Halos for maximum AgNPs loading was calculated to 18.89 ± 0.15 mm for S. aureus and 21.38 ± 0.17 mm for E. coli. An initial burst release of silver elements within 24 h was observed in the inductively coupled plasma-atomic emission spectrometry (ICP-AES) test, and the release amounts were proportionally expansive with the increase in Ag contents. Our results demonstrated that such types of composite nanofibers have a strong potential to be used in biomedicine.

Evaluating Antibacterial Efficacy and Biocompatibility of PAN Nanofibers Loaded with Diclofenac Sodium Salt.

Side effects of the drugs' oral administration led us to examine the possibility of using diclofenac sodium (DLF) in a polymeric drug delivery system based on electrospun polyacrylonitrile (PAN) nanofibers, which can be produced cost-effectively and with good applicability for transdermal treatments. The inclusion of DLF in PAN nanofibers increased the nanofiber diameter from ~200 nm to ~500 nm. This increase can be attributed to the increase in the spinning solution viscosity. FTIR spectra confirm the entrapment of the DLF into the PAN nanofibers. X-ray diffraction pattern showed that the inclusion of the DLF in the PAN nanofibers had caused the misalignment in the polymeric chains of the PAN, thus resulting in a decrease of the peak intensity at 2θ = 17o. The DLF loaded PAN nanofibers were efficient against the gram-positive Staphylococcus aureus (S. aureus) and gram-negative Escherichia coli (E. coli), with maximum inhibition zone of 16 ± 0.46 mm for E. coli and 15.5 ± 0.28 mm for S. aureus. Good cell viability ~95% for L929 cells in more extended incubation periods was reported. A gradual release of DLF from the PAN nanofiber was observed and can be attributed to the stability of Pan in PBS medium. Cell adhesion micrographs show that cell-cell interaction is stronger than the cell-material interaction. This type of weak cell interaction with the wound dressing is particularly advantageous, as this will not disturb the wound surface during the nursing of the wound.

Lignin-mediated in-situ synthesis of CuO nanoparticles on cellulose nanofibers: A potential wound dressing material.

Herein we present our research on the synthesis of CuO nanoparticles on the surface of electrospun cellulose (CE) nanofibers using alkali lignin as a reducing agent. Fascinatingly, CA nanofibers were deacetalized during alkali lignin treatment, which was verified by FTIR-ATR spectra. The morphology of the produced nanofibers was observed with SEM and TEM. The presence of CuO nanoparticles was verified by EDX, XRD, and XPS. The Cu/CE nanofibers showed low thermal stability. MVTR values of 2100-1900 g/m2/day are adequate for the transport of air and moisture from the wound surface. The Cu/CE showed faster release (80%) of copper ions to aqueous environment within 24 h and seemed to advance towards plateau for the next five days. The Cu/CE nanofibrous mats exhibited excellent antibacterial efficacy against both gram-negative Escherichia coli (E. coli) and gram-positive Staphylococcus aureus (S. aureus) bacteria. NIH3T3 fibroblast cells have excellent migrating and proliferating ability on our prepared nanofibrous mats. The presence of bound alkali lignin on the surface of nanofibers added a benefit of antioxidant activity. These findings revealed that such type of nanofibrous mats could be used as a potential wound dressing material.

Carboxymethyl Cellulose (CMC) Based Electrospun Composite Nanofiber Mats for Food Packaging.

Cellulose is one of the most abundantly available natural polymers. Carboxymethyl cellulose (CMC) belongs to the cellulose family and has different degrees of substitution. Current research comprises the fabrication and characterization of CMC nanofibers using polyvinyl alcohol (PVA) and polyvinylpyrrolidone (PVP) as capping agents and carriers for sustainable food packaging applications. Recently authors successfully fabricated smooth and uniform nanofibers of stated polymers and optimized the ratios of three polymers for continuous production. However, in this research, it was further characterized for mechanical properties, surface properties, structural properties, air permeability, and chemical properties to confirm the suitability and scope of tri-component nanofibrous mats in food packaging applications. Different fruits and vegetables were packed in a plastic container and closed by nanofiber mats and by a plastic lid. All samples were observed after a specific period of time (fruits were kept for 40 days while vegetables were kept for 10 days in the controlled environment). It was observed in the results that fruits and vegetables closed by nanofiber based webs exhibited better freshness and lower accumulation of moisture as compared to that of containers with plastic lids. From the results of performed tests, it was observed that nanofiber mats possess enough mechanical, structural, and morphological properties to be used as food packaging.

Bioactive Sambong oil-loaded electrospun cellulose acetate nanofibers: Preparation, characterization, and in-vitro biocompatibility.

Blumea balsamifera oil loaded cellulose acetate nanofiber mats were prepared by electrospinning. The inclusion of blumea oil increased the nanofiber diameter. FTIR spectra confirm the addition of blumea oil in the nanofiber mats. The XRD pattern suggests that the inclusion of blumea oil has caused a misalignment in the polymer chains of the cellulose acetate. Thus, a decrease in the tensile strength was observed for the blumea oil loaded nanofibers. The increase in fiber diameter causes a reduction in the porosity of the nanofiber mats. The blumea oil loaded nanofiber mats showed antibacterial efficacy against Escherichia coli and Staphylococcus aureus. The blumea oil showed antioxidant abilities against the DPPH solution. MVTR of the neat and blumea oil loaded nanofiber mats was in the range of 2450-1750 g/m2/day, which is adequate for the transport of air and moisture from the wound surface. Blumea oil loaded mats showed good cell viability ~92% for NIH 3T3 cells in more extended periods of incubation. A biphasic release profile was obtained, and the release followed the first-order kinetics depending upon the highest value of the coefficient of correlation R 2 (88.6%).