Experimental Study of the Airflow Field and Fiber Motion in the Melt-Blowing Process.

The melt-blowing process involves high velocity airflow and fiber motion, which have a significant effect on fiber attenuation. In this paper, the three-dimensional airflow field for a melt-blowing slot die was measured using the hot-wire anemometry in an experiment. The fiber motion was captured online using a high-speed camera. The characteristics of the airflow distribution and fiber motion were analyzed. The results show that the melt-blowing airflow field is asymmetrically distributed. The centerline air velocity is higher than that around it and decays quickly. The maximum airflow velocity exists near the die face, in the range of 130-160 m/s. In the region of -0.3 cm < y < 0.3 cm and 0 < z < 2 cm, the airflow has a high velocity (>100 m/s). As the distance of z reaches 5 cm and 7 cm, the maximum airflow velocity reduces to 70 m/s. The amplitude of fibers is calculated, and it increases with the increase in air dispersion area which has a significant influence on fiber attenuation. At z = 1.5 cm, 2.5 cm, 4 cm, and 5.5 cm, the average fiber amplitudes are 1.05 mm, 1.71 mm, 2.83 mm, and 3.97 mm, respectively. In the vicinity of the die, the fibers move vertically downward as straight segments. With the increase in distance from the spinneret, the fiber appears to bend significantly and forms a fiber loop. The fiber loop morphology affects the velocity of the fiber movement, causing crossover, folding, and bonding of the moving fiber. The study investigated the interaction between the fiber and airflow fields. It indicates that the airflow velocity, velocity difference, and dispersion area can affect the motion of fiber which plays an important role in fiber attenuation during the melt-blowing process.

Superhydrophobic and Breathable Polyacrylonitrile/Silica/Perfluoroalkyl Ethyl Methacrylate Nanofiber Membranes Prepared by Solution Blow Spinning.

Hydrophobic and breathable nanofiber membranes have attracted considerable attention owing to their applications in various fields. In this study, we fabricated superhydrophobic and breathable nanofiber membranes using solution blow spinning. We optimized the spinning process parameters by analyzing their effects on the structure and properties of the nanofiber membranes. And the nanofiber membranes achieved superhydrophobicity through hydrophobic modification treatment. The average fiber diameter and pore size of the obtained membrane were 0.51 and 13.65 µm, respectively. The membranes exhibited superhydrophobicity, breathability, and mechanical properties: water vapor transmission of 12.88 kg/m2/day, air permeability of 10.97 mm/s, water contact angle of 150.92°, maximum tensile stress of 5.36 MPa, and maximum elongation at break of 12.27%. Additionally, we studied the impact of heat treatment on the nanofiber membranes. The membranes prepared in this study can be applied to protective garments, outdoor clothing, antifouling materials, etc. Because of its relatively higher production efficiency, solution blow spinning is a prospective method for producing functional nanofibers.

Formation Mechanism of Fibrous Web in the Solution Blowing Process.

Solution blowing (SB) is a widely reported technology that can be used to fabricate fibers at the micro- and nanoscale. To reveal the fibrous web formation mechanism in SB, we improved our previous melt blowing (MB) model to predict fibrous web structures. Then, we fabricated two samples and simulated the same number of virtual samples in the computer to verify the model. Thereafter, we measured the structural parameters including the fiber diameter, fiber orientation, basis weight, and pore size. Our model provides a good prediction of the fiber orientation and basis weight. However, the predicted fiber diameter was slightly smaller than the measured diameter. The experimental pore size distribution was also different from that in the simulated results. The model provides a virtual fabrication process to reveal a fibrous web formation mechanism and finds a similar distribution of these structural parameters between SB and MB.

Quantitative Trait Locus Mapping and Identification of Candidate Genes for Resistance to Fusarium Wilt Race 7 Using a Resequencing-Based High Density Genetic Bin Map in a Recombinant Inbred Line Population of Gossypium barbadense.

Fusarium wilt caused by Fusarium oxysporum f. sp. vasinfectum (FOV) is one of the most destructive diseases in cotton (Gossypium spp.) production, and use of resistant cultivars is the most cost-effective method managing the disease. To understand the genetic basis of cotton resistance to FOV race 7 (FOV7), this study evaluated a recombinant inbred line (RIL) population of 110 lines of G. barbadense from a cross between susceptible Xinhai 14 and resistant 06-146 in eight tests and constructed a high-density genetic linkage map with resequencing-based 933,845 single-nucleotide polymorphism (SNP) markers covering a total genetic distance of 2483.17 cM. Nine quantitative trait loci (QTLs) for FOV7 resistance were identified, including qFOV7-D03-1 on chromosome D03 in two tests. Through a comparative analysis of gene expression and DNA sequence for predicted genes within the QTL region between the two parents and selected lines inoculated with FOV7, GB_D03G0217 encoding for a calmodulin (CaM)-like (CML) protein was identified as a candidate gene. A further analysis confirmed that the expression of GB_D03G0217 was suppressed, leading to increased disease severity in plants of the resistant parent with virus induced gene silencing (VIGS).

MTR-G is a high-risk allele for lower-extremity arteriosclerotic occlusion.

OBJECTIVE: This study investigated the relationship between the MTRA2576G polymorphism of the key enzyme in homocysteine metabolism and deep vein thrombosis (DVT), chronic venous insufficiency (CVI) and arteriosclerotic occlusion (ASO) of the lower extremities. METHODS: Genomic DNA was extracted from the peripheral blood of patients with lower-extremity vascular diseases, including 125 cases of DVT, 125 cases of CVI and 125 cases of ASO. DNA samples extracted from 197 healthy individuals were used as control samples. PCR-RFLP was used to investigate the polymorphisms of MTR in these subjects. RESULTS: The frequency of the G allele in MTR was 6.8%, 6.1% and 12.8% for the DVT group, CVI group and ASO group, respectively (p = 0.003). The frequency of the GG allele was 13.6%, 12.2% and 22.4% for the DVT group, CVI group and ASO group, respectively (p = 0.014). Only the allele frequency of GG in the ASO group was higher than that in the control group, and the disease risk was also 1.3 times higher than that in the control group (OR = 1.299, 95% CI = 1.025 ∼ 2.575). CONCLUSION: Patients with the G allele in MTR have a high risk for ASO, and the GG allele is a risk gene for ASO.

Driver behaviour and traffic accident involvement among professional heavy semi-trailer truck drivers in China.

The purpose of this study was to develop a driving behavior scale for professional drivers of heavy semi-trailer trucks in China, and study the causes of such driving behavior and its impact on traffic safety operation. Data was processed by IBM SPSS 25. In addition to principal component analysis, Promax rotation, Bartlett's test, Cronbach's alpha, correlation analysis and binary logistic regression were examined. A DBQ with 4 dimensions and 20 items, and a PDBQ with 1 dimension and 6 items were developed for professional drivers of heavy semi-trailer trucks in China. The KMO coefficients of PDBQ and DBQ were 0.822 and 0.852, respectively, and the significant level of Bartlett's popularity test was p < 0.0001. The accident prediction model showed that the variables related to traffic accidents were negligence/lapses and driving time of heavy semi-trailer truck drivers. 1-5 a.m. was found to be the most dangerous period for drivers of medium and heavy semi-trailer trucks, during which accidents were most likely to happen. As negligence/lapses increased by one unit, the probability of traffic accidents increased by 2.293 times.

Curcumin protects against inflammation and lung injury in rats with acute pulmonary embolism with the involvement of microRNA-21/PTEN/NF-κB axis.

This study was intended to investigate the effect of Curcumin on acute pulmonary embolism (APE) via microRNA-21 (miR-21)/PTEN/NF-κB axis. APE model was induced on rats and administrated with Curcumin. Western blot analysis and RT-qPCR manifested the downregulation of Sp1, miR-21 and NF-κB, but the upregulation of PTEN in Curcumin-treated APE rats. Blood gas analysis, ELISA, and weighing of wet weight/dry weight (W/D) ratio indicated that Curcumin diminished mPAP and RVSP levels, W/D ratio, thrombus volume, and inflammatory factors in the lungs of APE rats. Further mechanical analysis was conducted by dual-luciferase reporter assays and ChIP assay, which showed that Sp1 increased miR-21 expression by binding to the miR-21 promoter, and that PTEN was targeted by miR-21. The APE rats were injected with adenovirus to evaluate the effect of Sp1, miR-21, or PTEN on lung injury and inflammation. It was observed that downregulation of miR-21 or Sp1, or upregulation of PTEN diminished mPAP and RVSP levels, W/D ratio, thrombus volume, and inflammatory factors in the lungs of APE rats. In summary, Curcumin decreased miR-21 expression by downregulating Sp1 to upregulate PTEN and to impair the NF-κB signaling pathway, thus suppressing lung injury and inflammation in APE rats.

Lateral Diffusion of a Free Air Jet in Slot-Die Melt Blowing for Microfiber Whipping.

In melt blowing, microfibrous nonwoven material is manufactured by using high-speed air to attenuate polymer melt. The melt-blown air jet determines the process of polymer attenuation and fiber formation. In this work, the importance of lateral velocity on the fiber was first theoretical verified. The lateral diffused characteristic of the air flow field in slot-die melt blowing was researched by measuring the velocity direction using a dual-wire probe hot-wire anemometer. Meanwhile, the fiber path was captured by high-speed photography. Results showed that there existed a critical boundary of the lateral diffusion, however, air jets in the x-z plane are a completely diffused field. This work indicates that the lateral velocity in the y-z plane is one of the crucial factors for initiating fiber whipping and fiber distribution.