Optimization of CoFe2O4 nanoparticles and graphite fillers to endow thermoplastic polyurethane nanocomposites with superior electromagnetic interference shielding performance.

The rapid growth, integration, and miniaturization of electronics have raised significant concerns about how to handle issues with electromagnetic interference (EMI), which has increased demand for the creation of EMI shielding materials. In order to effectively shield against electromagnetic interference (EMI), this study developed a variety of thermoplastic polyurethane (TPU)-based nanocomposites in conjunction with CoFe2O4 nanoparticles and graphite. The filler percentage and nanocomposite thickness were tuned and optimized. The designed GF15-TPU nanocomposite, which has a 5 mm thickness, 15 weight percent cobalt ferrite nanoparticles, and 35 weight percent graphite, showed the highest total EMI shielding effectiveness value of 41.5 dB in the 8.2-12.4 GHz frequency range, or 99.993% shielding efficiency, out of all the prepared polymer nanocomposites. According to experimental findings, the nanocomposite's dipole polarization, interfacial polarization, conduction loss, eddy current loss, natural resonance, exchange resonance, multiple scattering, and high attenuation significantly contribute to improving its electromagnetic interference shielding properties. The created TPU-based nanocomposites containing graphite and CoFe2O4 nanoparticles have the potential to be used in communication systems, defense, spacecraft, and aircraft as EMI shielding materials.

Giant Response and Selectivity of Hansen Solubility Parameters-Based Graphene-SBS Co-Polymer Matrix Composite Room Temperature Sensor to Organic Vapours.

A styrene-butadiene-styrene co-polymer matrix nanocomposite filled with graphene nanoplatelets was studied to prepare chemiresistive volatile organic compounds (VOCs) room temperature sensors with considerable response and selectivity. Nanofiller concentration was estimated from the electrical conductivity percolation behaviour of the nanocomposite. Fabricated sensors provided selective relative responses to representative VOCs differing by orders of magnitude. Maximum observed average relative responses upon exposure to saturated vapours of the tested VOCs were ca. 23% for ethanol, 1600% for acetone, and the giant values were 9 × 106% for n-heptane and 10 × 106% for toluene. The insensitivity of the sensor to the direct saturated water vapour exposure was verified. Although high humidity decreases the sensor's response, it paradoxically enhances the resolution between hydrocarbons and polar organics. The non-trivial sensing mechanism is explained using the Hansen solubility parameters (HSP), enabling a rational design of new sensors; thus, the HSP-based class of sensors is outlined.

Chitosan/dialdehyde cellulose hydrogels with covalently anchored polypyrrole: Novel conductive, antibacterial, antioxidant, immunomodulatory, and anti-inflammatory materials.

In this work, conductive composite hydrogels with covalently attached polypyrrole (PPy) nanoparticles are prepared. Hydrogels are based on partially re-acetylated chitosan soluble at physiological pH without any artificial structural modifications or need for an acidic environment, which simplifies synthesis and purification. Low-toxic and sustainable dialdehyde cellulose (DAC) was used for crosslinking chitosan and covalent anchoring of PPy colloidal particles. The condensation reaction between DAC and PPy is reported for the first time and improves not only the anchoring of PPy particles but also control over the properties of the final composite. The soluble chitosan and PPy particles are shown to act in synergy, which improves the biological properties of the materials. Prepared composite hydrogels are non-cytotoxic, non-irritating, antibacterial, can capture reactive oxygen species often related to excessive inflammation, have conductivity similar to human tissues, enhance in vitro cell growth (migration assay), and have immunomodulatory effects related to the stimulation of neutrophils and macrophages. The covalent attachment of PPy also strengthens the hydrogel network. The aldol condensation as a method for PPy covalent anchoring thus presents an interesting possibility for the development of advanced biomaterials in the future.

Polylactide-Based Nonisocyanate Polyurethanes: Preparation, Properties Evaluation and Structure Analysis.

This study investigated the successful synthesis and characterization of nonisocyanate polyurethanes (NIPUs) based on polylactide. The NIPUs were synthesized by a condensation reaction of oligomers with hard segments (HSs) and synthesized carbamate-modified polylactic acid containing flexible segments (FSs). The oligomers with HSs were prepared from phenolsulfonic acid (PSA) or a mixture of PSA and hydroxynaphthalenesulfonic acid (HNSA), urea and formaldehyde. The mixing of oligomeric compounds with different amounts of formaldehyde was carried out at room temperature. Obtained NIPU samples with different hard segment content were tested for their mechanical and thermal properties. The tensile strength (TS) of all NIPU samples increased with an increasing amount of HSs, attaining the maximum value at an HS:FS ratio of 1:3. Samples prepared from PSA and HNSA showed higher tensile strength (TS) without significant change in elongation at break compared to the samples based only on PSA. Thermogravimetric analysis data indicated an absence of weight loss for all samples below 100 °C, which can be considered a safe temperature for using NIPU materials. Maximum degradation temperatures reached up to 385 °C. Fourier transform infrared spectroscopy results confirmed the existence of expected specific groups as well as the chemical structure of the prepared polyurethanes. DSC analysis showed the existence of two characteristic phase transitions attributed to the melting and crystallization of hard segments in the NIPU samples.

Propylene Metathesis over Molybdenum Silicate Microspheres with Dispersed Active Sites.

In this work, we demonstrate that amorphous and porous molybdenum silicate microspheres are highly active catalysts for heterogeneous propylene metathesis. Homogeneous molybdenum silicate microspheres and aluminum-doped molybdenum silicate microspheres were synthesized via a nonaqueous condensation of a hybrid molybdenum biphenyldicarboxylate-based precursor solution with (3-aminopropyl)triethoxysilane. The as-prepared hybrid metallosilicate products were calcined at 500 °C to obtain amorphous and porous molybdenum silicate and aluminum-doped molybdenum silicate microspheres with highly dispersed molybdate species inserted into the silicate matrix. These catalysts contain mainly highly dispersed MoOx species, which possess high catalytic activity in heterogeneous propylene metathesis to ethylene and butene. Compared to conventional silica-supported MoOx catalysts prepared via incipient wetness impregnation (MoIWI), the microspheres with low Mo content (1.5-3.6 wt %) exhibited nearly 2 orders of magnitude higher steady-state propylene metathesis rates at 200 °C, approaching site time yields of 0.11 s-1.

Controlled Drug Delivery Device for Cornea Treatment and Novel Method for Its Testing.

A new solution for local anesthetic and antibiotic delivery after eye surgery is presented. A contact lens-shaped collagen drug carrier was created and loaded by Levofloxacin and Tetracaine with a riboflavin crosslinked surface layer, thus impeding diffusion. The crosslinking was confirmed by Raman spectroscopy, whereas the drug release was investigated using UV-Vis spectrometry. Due to the surface barrier, the drug gradually releases into the corneal tissue. To test the function of the carrier, a 3D printed device and a new test method for a controlled drug release, which mimics the geometry and physiological lacrimation rate of the human eye, were developed. The experimental setup with simple geometry revealed that the prepared drug delivery device can provide the prolonged release profile of the pseudo-first-order for up to 72 h. The efficiency of the drug delivery was further demonstrated using a dead porcine cornea as a drug recipient, without the need to use live animals for testing. Our drug delivery system significantly surpasses the efficiency of antibiotic and anesthetic eyedrops that would have to be applied approximately 30 times per hour to achieve the same dose as that delivered continuously by our device.

Incorporation of the New anti-Octadecaborane Laser Dyes into Thin Polymer Films: A Temperature-Dependent Photoluminescence and Infrared Spectroscopy Study.

New anti-octadecaborane(22) laser dyes have been recently introduced. However, their application in solid thin films is limited, despite being very desirable for electronics. Spectroscopic methods, photoluminescence (PL), and infrared reflection-absorption spectroscopy (IRRAS), are here used to reveal structural responses to a temperature change in thin polymer films made of π- and σ-conjugated and non-conjugated polymers and anti-octadecaborane(22) and its tetra-alkylatedderivatives. It has been observed that borane clusters are not firmly fixed within polymer matrices and that their ability for diffusion out of the polymer film is unprecedented, especially at higher temperatures. This ability is related to thermodynamic transitions of polymer macromolecular chains. PL and IRRAS spectra have revealed a clear correlation with ß-transition and α-transition of polymers. The influence of structure and molecular weight of a polymer and the concentration and the substitution type of clusters on mobility of borane clusters within the polymer matrix is demonstrated. A solution is proposed that led to an improvement of the temperature stability of films by 45 °C. The well-known spectroscopic methods have proved to be powerful tools for a non-routine description of the temperature behavior of both borane clusters and polymer matrices.

New approach to prepare cytocompatible 3D scaffolds via the combination of sodium hyaluronate and colloidal particles of conductive polymers.

Bio-inspired conductive scaffolds composed of sodium hyaluronate containing a colloidal dispersion of water-miscible polyaniline or polypyrrole particles (concentrations of 0.108, 0.054 and 0.036% w/w) were manufactured. For this purpose, either crosslinking with N-(3-dimethylaminopropyl-N-ethylcarbodiimide hydrochloride and N-hydroxysuccinimid or a freeze-thawing process in the presence of poly(vinylalcohol) was used. The scaffolds comprised interconnected pores with prevailing porosity values of ~ 30% and pore sizes enabling the accommodation of cells. A swelling capacity of 92-97% without any sign of disintegration was typical for all samples. The elasticity modulus depended on the composition of the scaffolds, with the highest value of ~ 50 kPa obtained for the sample containing the highest content of polypyrrole particles. The scaffolds did not possess cytotoxicity and allowed cell adhesion and growth on the surface. Using the in vivo-mimicking conditions in a bioreactor, cells were also able to grow into the structure of the scaffolds. The technique of scaffold preparation used here thus overcomes the limitations of conductive polymers (e.g. poor solubility in an aqueous environment, and limited miscibility with other hydrophilic polymer matrices) and moreover leads to the preparation of cytocompatible scaffolds with potentially cell-instructive properties, which may be of advantage in the healing of damaged electro-sensitive tissues.

Application of reverse engineering in the field of pharmaceutical tablets using Raman mapping and chemometrics.

Raman micro-spectroscopy technique offers a combination of relatively high spatial resolution with identification of components or mixtures of components in different sample areas, e.g. on the surface or the cross-section of a sample. This study is focused on the analysis of the tablets from pharmaceutical development with different technological parameters: (1) the manufacturing technology, (2) the particle size of the input API (active pharmaceutical ingredient) and (3) the quantitative composition of the individual excipients. These three mentioned parameters represent the most frequently solved problems in the field of reverse engineering in pharmacy. The investigation aims to distinguish tablets with the above-described technological parameters with limited subjective steps by Raman microscopy. Furthermore, non-subjective methods of Raman data analysis using advanced statistical analysis have been proposed, namely Principal Component Analysis, Soft Independent Modelling of Class Analogy and Linear Discriminant Analysis. The methods successfully distinguished and identified even very small differences in the analysed tablets within our study and provided objective statistic evaluation of Raman maps. The information on component and particle size distribution including their small differences, which is the critical parameter in the development of the original and generic products, was obtained due to combination of these methods. Even though each of these chemometric methods evaluates the data set from a different perspective, their mutual application on the problem of Raman maps evaluation confirmed and specified results on level that would be unattainable with the use of only one them.

The Photostability of Novel Boron Hydride Blue Emitters in Solution and Polystyrene Matrix.

In recent work, the boron hydride anti-B18H22 was announced in the literature as a new laser dye, and, along with several of its derivatives, its solutions are capable of delivering blue luminescence with quantum yields of unity. However, as a dopant in solid polymer films, its luminescent efficiencies reduce dramatically. Clarification of underlying detrimental effects is crucial for any application and, thus, this contribution makes the initial steps in the use of these inorganic compounds in electrooptical devices based on organic polymer thin films. The photoluminescence behavior of the highly luminescent boron hydrides, anti-B18H22 and 3,3',4,4'-Et4-anti-B18H18, were therefore investigated. The quantum yields of luminescence and photostabilities of both compounds were studied in different solvents and as polymer-solvent blends. The photophysical properties of both boranes are evaluated and discussed in terms of their solvent-solute interactions using photoluminescence (PL) and NMR spectroscopies. The UV degradability of prepared thin films was studied by fluorimetric measurement. The effect of the surrounding atmosphere, dopant concentration and the molecular structure were assessed.

Effect of Structure of Polymers Grafted from Graphene Oxide on the Compatibility of Particles with a Silicone-Based Environment and the Stimuli-Responsive Capabilities of Their Composites.

This study reports the utilization of controlled radical polymerization as a tool for controlling the stimuli-responsive capabilities of graphene oxide (GO) based hybrid systems. Various polymer brushes with controlled molecular weight and narrow molecular weight distribution were grafted from the GO surface by surface-initiated atom transfer radical polymerization (SI-ATRP). The modification of GO with poly(n-butyl methacrylate) (PBMA), poly(glycidyl methacrylate) (PGMA), poly(trimethylsilyloxyethyl methacrylate) (PHEMATMS) and poly(methyl methacrylate) (PMMA) was confirmed by thermogravimetric analysis (TGA) coupled with online Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM) and X-ray photoelectron spectroscopy (XPS). Various grafting densities of GO-based materials were investigated, and conductivity was elucidated using a four-point probe method. Raman shift and XPS were used to confirm the reduction of surface properties of the GO particles during SI-ATRP. The contact angle measurements indicated the changes in the compatibility of GOs with silicone oil, depending on the structure of the grafted polymer chains. The compatibility of the GOs with poly(dimethylsiloxane) was also investigated using steady shear rheology. The tunability of the electrorheological, as well as the photo-actuation capability, was investigated. It was shown that in addition to the modification of conductivity, the dipole moment of the pendant groups of the grafted polymer chains also plays an important role in the electrorheological (ER) performance. The compatibility of the particles with the polymer matrix, and thus proper particles dispersibility, is the most important factor for the photo-actuation efficiency. The plasticizing effect of the GO-polymer hybrid filler also has a crucial impact on the matrix stiffness and thus the ability to reversibly respond to the external light stimulation.

Reversible Actuation Ability upon Light Stimulation of the Smart Systems with Controllably Grafted Graphene Oxide with Poly (Glycidyl Methacrylate) and PDMS Elastomer: Effect of Compatibility and Graphene Oxide Reduction on the Photo-Actuation Performance.

This study is focused on the controllable reduction of the graphene oxide (GO) during the surface-initiated atom transfer radical polymerization technique of glycidyl methacrylate (GMA). The successful modification was confirmed using TGA-FTIR analysis and TEM microscopy observation of the polymer shell. The simultaneous reduction of the GO particles was confirmed indirectly via TGA and directly via Raman spectroscopy and electrical conductivity investigations. Enhanced compatibility of the GO-PGMA particles with a polydimethylsiloxane (PDMS) elastomeric matrix was proven using contact angle measurements. Prepared composites were further investigated through the dielectric spectroscopy to provide information about the polymer chain mobility through the activation energy. Dynamic mechanical properties investigation showed an excellent mechanical response on the dynamic stimulation at a broad temperature range. Thermal conductivity evaluation also confirmed the further photo-actuation capability properties at light stimulation of various intensities and proved that composite material consisting of GO-PGMA particles provide systems with a significantly enhanced capability in comparison with neat GO as well as neat PDMS matrix.

Gas-phase fragmentation of 1-adamantylbisimidazolium salts and their complexes with cucurbit[7]uril studied using selectively 2 H-labeled guest molecules.

RATIONALE: Bisimidazolium salts (BIMs) represent an interesting family of ditopic ligands that are used in the construction of supramolecular systems with hosts based on cyclodextrins or cucurbit[n]urils. Understanding the fragmentation mechanism of individual BIMs and how this mechanism changes after complexation with cucurbit[n]urils can bring new insight into the intrinsic host-guest relationship, thereby allowing utilization of mass spectrometry to describe binding behavior. METHODS: Selectively 2 H-labeled bisimidazolium salts were prepared and fully characterized by spectroscopic methods. All MSn experiments were conducted in the positive-ion mode using an electrospray ionization (ESI) ion-trap mass spectrometer. The structures of the proposed fragments were supported by theoretical optimizations performed at the B3LYP/6-31G(d) level of density functional theory (DFT) using the Spartan'14 program. RESULTS: Using selectively deuterium-labeled isotopologues of two adamantylated bisimidazolium salts and DFT calculations, we describe the fragmentation pathways of bisimidazolium salts. The release of two important adamantane moieties, [C11 H17 ]+ and C11 H16 , from M2+ was determined, although the former was strongly preferred. In contrast, when M2+ was complexed with CB7, the neutral loss of the C11 H16 fragment was favored. The fragmentation pattern strongly depended on the steric hindrance of the M2+ guest against slippage of the CB7 unit over the guest molecular axle. CONCLUSIONS: The structures of two adamantane-based fragments and the mechanisms of their formation were rationalized. Two distinct geometric arrangements for the adamantane cage inside the CB7 cavity were hypothesized to explain the differences in the fragmentation patterns for guests with minimal, moderate, and high steric hindrance. This finding brings new insight into the understanding of intrinsic behavior of the adamantane-based guests inside the CB7 cavity.

Effect of backbone conformation and its defects on electronic properties and assessment of the stabilizing role of π-π interactions in aryl substituted polysilylenes studied by DFT on deca[methyl(phenyl)silylene]s.

BACKGROUND: Recent efforts in the field of mesoscale effects on the structure and properties of thin polymer films call to revival interest in conformational structure and defects of a polymer backbone which has a crucial influence on electronic properties of the material. Oligo[methyl(phenyl)silylene]s (OMPSi) as exemplary molecules were studied theoretically by DFT in the form of optimal decamers and conformationally disrupted decamers (with a kink). RESULTS: We proved that transoid backbone conformation is true energy minimum and that a kink in the backbone causes significant hypsochromic shift of the absorption maximum (λ max ), while backbone conformation altering from all-eclipsed to all-anti affects λ max in the opposite way. π-π stacking was investigated qualitatively through optimal geometry of OMPSi and mutual position of their phenyls along the backbone and also quantitatively by an evaluation of molecular energies obtained from single point calculations with functionals, which treat the dispersion effect in the varying range of interaction. CONCLUSIONS: The kink was identified as a realistic element of the conformational structure that could be able to create a bend in a real aryl substituted polysilylene chain because it is stabilized by attractive π-π interactions between phenyl side groups.Graphical abstract.

Theoretical study of polaron binding energy in conformationally disrupted oligosilanes.

Density functional theory was used for a quantum chemical study of oligo[methyl(phenyl)silylene] structures containing a conformational defect: a kink in the silicon backbone. Oligomers were studied in the neutral state as well as in the form of positive (P(+)) and negative (P(-)) polaron quasiparticles. Computations performed using the B3LYP model and the 6-31G(d) basis set revealed that the charge distribution is not influenced by the presence of the kink, but the positive charge on the Si backbone differs slightly in P(+) and P(-) quasiparticles. On the other hand, the spin density is significantly shifted away from the chain part that contains the kink, and this effect is more intense in P(-) polarons. Changes in electron density are also evident from the frontier molecular orbital distribution. The deformation energy (which is associated with the relaxation of polarons) decreases with the number of atoms in the oligomer backbone in P(+) but shows the opposite behavior for P(-) quasiparticles.