RESUMO
Specific cues provided to cells by the extracellular matrix (ECM) are determined by its composition. Except of collagens other naturally occurring ECM components should be considered in designing 3D models of diseases. We used spectrophotometric and rheological measurements and confocal imaging to characterise collagen matrices of human origin that can be modified by clinically relevant ECM components. pH of the neutralising solution, but not incubation of solidified collagen matrices in serum-free culture medium with pH 5.0-9.0 affected distribution of collagen fibres. Admixture of fibronectin or tenascin-C influenced assembly kinetics and resulted in slight increase in the Young's moduli of the matrices, indicating their incorporation into the collagen matrices. Co-localization of fibronectin with collagen fibres was confirmed by fluorescence imaging. Various cell types relevant for tumour tissue were able to proliferate within the matrices suggesting that they can be used to study role of ECM components in cancer in spatial models.
Assuntos
Colágeno Tipo I , Neoplasias , Humanos , Colágeno Tipo I/química , Fibronectinas/análise , Fibronectinas/química , Fibronectinas/metabolismo , Células Cultivadas , Colágeno/química , Matriz Extracelular/metabolismo , Técnicas de Cultura de CélulasRESUMO
This work focuses on the fabrication of lanthanum cerate (La2Ce2O7, LC) powders via two chemical routes: modified Pechini sol-gel method and solid-state synthesis. The synthesized LC powders were heat treated in the temperature range of 1000-1400 °C for 6 h and investigated as a material for thermal barrier coating (TBC) applications. For this purpose, the powder morphology, chemical composition, crystal structure and thermal stability were studied. Scanning electron microscopy (SEM) of the synthesized powders revealed an agglomerated structure consisting of fine and uniformly distributed grains. Energy-dispersive X-ray spectroscopy (EDXS) indicated that the chemical compositions of the LC powders were similar to the stoichiometric ratio of La2Ce2O7. A cubic fluorite structure was observed by X-ray diffraction analysis (XRD) after calcining the LC powder prepared by solid-state synthesis at 1300 °C. In contrast, there was always a fluorite structure in the LC powder synthesized by the Pechini sol-gel method after heat treatment over the entire temperature range. The thermal behavior of the LC powders was analyzed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TG) in the temperature range of 25-1300 °C. Neither an obvious mass change nor a visible energy change was observed within the tested temperature range, indicating high phase stability of the LC powder and its suitability for TBC applications. Spheroidization on the prepared LC powders was also investigated, revealing that powder size and morphology had a significant impact on the spheroidization efficiency.
RESUMO
In this work, La2Ce2O7-yttria-stabilized zirconia (LC-YSZ) composites with different weight fractions of YSZ (40−70 wt.%) were prepared by hot pressing at 1400 °C and investigated as a material for thermal barrier-coating (TBC) applications. For this purpose, the effect of YSZ addition on the phase composition, microstructure, mechanical performance and thermal behavior was studied. X-ray diffraction analysis showed that the LC-YSZ composites were mainly composed of a cubic ZrO2 and La2O3-CeO2-ZrO2 solid solution with a pyrochlore structure, indicating that the reaction between LC and YSZ took place during hot pressing. Scanning electron microscopy revealed the high microstructural stability of the prepared composites, as the pore formation was significantly controlled and a high relative density (>97%) was obtained. The microstructure of LC-YSZ bulk samples was relatively fine-grained, with an average grain size below or very close to 1 µm. YSZ doping improved the Vickers hardness of the LC-YSZ composites; the highest hardness, with value of 12 ± 0.62 GPa, was achieved for the composite containing 70 wt.% of YSZ. The fracture toughness of LC-YSZ composites was in the range from 2.13 to 2.5 MPa·m1/2. No statistically significant difference in heat capacity or thermal conductivity was found between the composites with different content of YSZ. The results showed that LC-YSZ composites have relatively low thermal conductivities from room temperature (1.5−1.8 W·m−1·K−1) up to 1000 °C (2.5−3.0 W·m−1·K−1). This indicates that the prepared LC-YSZ composite materials are promising candidates for TBC applications.
RESUMO
Three and five-layered silicon carbide-based composites containing 0, 5, and 15 wt.% of graphene nanoplatelets (GNPs) were prepared with the aim to obtain a sufficiently high electrical conductivity in the surface layer suitable for electric discharge machining (EDM). The layer sequence in the asymmetric three-layered composites was SiC/SiC-5GNPs/SiC-15GNPs, while in the symmetric five-layered composite, the order of layers was SiC-15GNPs/SiC-5GNPs/SiC/SiC-5GNPs/SiC-15GNPs. The layered samples were prepared by rapid hot-pressing (RHP) applying various pressures, and it was shown that for the preparation of dense 3- or 5-layered SiC/GNPs composites, at least 30 MPa of the applied load was required during sintering. The electrical conductivity of 3-layered and 5-layered composites increased significantly with increasing sintering pressure when measured on the SiC surface layer containing 15 wt.% of GNPs. The increasing GNPs content had a positive influence on the electrical conductivity of individual layers, while their instrumented hardness and elastic modulus decreased. The scratch tests confirmed that the materials consisted of well-defined layers with straight interfaces without any delamination, which suggests good adhesion between the individual layers.