Isolated Lateral Plating for Bicondylar Tibial Plateau Fractures: Factors Influencing Decision Making.

Lateral plating alone has been postulated as an alternative for fixation of bicondylar tibial plateau fractures in attempts to limit morbidity associated with dual plating. Characterization of fracture patterns that may facilitate lateral plating alone for bicondylar tibial plateau fractures is not well established. The authors analyzed radiographic and clinical outcomes of isolated lateral plating in patients with at least 6 months of follow-up. Of 56 patients identified, 37 (66%) had 41 AO Foundation (AO)/Orthopaedic Trauma Association (OTA) C1/C2 fractures with 19 (34%) presenting with 41 C3 fractures. Mean posteromedial articular fracture angle (PMAFA) was 69.9 degrees, with an average of 1.3 medial articular fragments. Only 16 patients (28%) had a PMAFA under 45 degrees. There were no cases of nonunion, and five patients (8.9%) developed wound infection during follow-up. Four patients (7.1%) experienced malreduction over three degrees, and eight patients (14.3%) experienced change in alignment over the follow-up duration, indicating some risk of inadequate fixation with this technique. (Journal of Surgical Orthopaedic Advances 33(2):088-092, 2024).

Biomechanical analysis of dual versus lateral locked plating in elderly bicondylar tibial plateau fractures: Does medial comminution matter?

OBJECTIVE: To assess dual plating versus lateral locked plate fixation of bicondylar tibial plateau fractures in an elderly cadaveric model with and without medial bone loss PARTICIPANTS: 10 pairs of elderly (range 78-93 years of age) fresh frozen tibias. INTERVENTION: Bicondylar tibial plateau fractures were created reproducing AO/OTA 41 C1 (without medial bone loss) and C2 fractures (with medial bone loss). Cadavers were randomized to 4 different groups. Groups 1 and 2 were 41 C1 fractures and fixated with either dual or lateral plating, respectively. Groups 3 and 4 were fixated in a similar fashion with medial metaphyseal bone loss (41 C2 fracture) with dual plating Group 3 and lateral plating group 4. Lateral plating consisted of a 3.5 mm 5-hole lateral plate (ALPS, ZimmerBiomet) with 6 bicortical locking screws proximally and two diaphyseal screws. Dual plating groups underwent lateral plating and additional 3.5 mm 5-hole posteromedial 1/3 tubular plate (ZimmerBiomet) placed at the apex of the fracture with two shaft screws and one unicortical screw proximally. Specimens were tested in a Mechanical Testing System (MTS) machine loading both condyles. OUTCOME MEASUREMENTS: Specimens were loaded to 300 N and coronal alignment obtained. Specimens were then cycled from 100 N to 700 N for 5000 cycles at 2 Hz. Average axial displacement, maximal displacement, average force and coronal alignment after 5000 cycles were recorded. Lastly, force to failure was recorded at 100 N/sec. RESULTS: Mean axial displacement was 4.21 mm ranging from 3.12 mm in group 1 to 5.92 mm in group 4 (P = 0.51). Failure force averaged 3340 N ranging from 4342 N in group 1 to 2433 N in group 4 (P = 0.36). Maximal displacement ranged from 3.69 mm in group 1 to 7.37 mm in group 4 (P = 0.21). Change in coronal alignment ranged from 0.98° in group 1 to 1.97° in group 4 (P = 0.45). No statistically significant difference was noted between all four groups for all data points. CONCLUSION: The results of this study demonstrate that a lateral locked plate may offer an alternative means of fixation in AO/OTA 41 C1 and C2 fractures.