De novo Powered Air-Purifying Respirator Design and Fabrication for Pandemic Response

The rapid spread of COVID-19 and disruption of normal supply chains resulted in severe shortages of personal protective equipment (PPE), particularly devices with few suppliers such as powered air-purifying respirators (PAPRs). A scarcity of information describing design and performance criteria represents a substantial barrier to new approaches to address these shortages. We sought to apply open-source product development to PAPRs to enable alternative sources of supply and further innovation. We describe the design, prototyping, validation, and user testing of locally manufactured, modular, PAPR components, including filter cartridges and blower units, developed by the Greater Boston Pandemic Fabrication Team (PanFab). Two designs, one with a fully custom-made filter and blower unit housing, and the other with commercially available variants (the "Custom" and "Commercial" designs respectively) were developed. Engineering performance of the prototypes was measured and safety validated using NIOSH-equivalent tests on apparatus available under pandemic conditions, at university laboratories. Feedback on designs was obtained from four individuals, including two clinicians working in an ambulatory clinical setting and two research technical staff for whom PAPR use is a standard part of occupational PPE. Respondents rated the PanFab Custom PAPR a 4 to 5 on a 5 Likert-scale 1) as compared to current PPE options, 2) for the sense of security with use in a clinical setting, and 3) for comfort. The three other versions of the designs (with a commercial blower unit, filter, or both) performed favorably, with survey responses consisting of scores ranging from 3-5. Engineering testing and clinical feedback demonstrate that the PanFab designs represents favorable alternative PAPRs in terms of user comfort, mobility, and sense of security. A nonrestrictive license promotes innovation in respiratory protection for current and future medical emergencies.

Can an interactive case-based activity help bridge the theory-practice gap in operative dentistry?

INTRODUCTION: A theory-practice gap in pre-doctoral dental education is a common source of stress for dental students. An interactive, small-group, case-based activity was designed to bridge the gap between pre-clinical and clinical experiences. The aim of our study was to assess the effectiveness of the case-based activity by evaluating students' comfort level in operative procedures. MATERIALS AND METHODS: Over 5 years, a total of 172 second-year students from the classes of 2017 through 2021 participated in the case-based activity delivered after the completion of the core operative dentistry course. The exercise included a pre-activity online quiz, an in-class case-based session and a laboratory exercise. Students' self-reported comfort levels in performing operative procedures were collected by surveys at three different times. They included the post-course survey distributed after the completion of the core operative dentistry course, the post-activity survey distributed after the completion of the case-based activity, and the follow-up survey distributed after students completed their first operative procedures in clinic. RESULTS: There was a 93% response rate. The average rating of all eight statements revealed statistically significant increase in students' comfort level after completing the case-based activity and after performing their first operative procedures in the teaching practice. CONCLUSION: This observation suggests that the case-based activity was effective in raising students' comfort levels. The activity may serve as an important tool in bridging the theory-practice gap between pre-clinical and clinical operative experiences.

Assessing the quality of nontraditional N95 filtering face-piece respirators available during the COVID-19 pandemic

BackgroundDuring the current COVID-19 pandemic, supply chains for Personal Protective Equipment (PPE) have been severely disrupted and many products, particularly surgical N95 filtering facepiece respirators (FFRs; "masks") are in short supply. As a consequence, an Emergency Use Authorization (EUA) from the FDA has allowed importation of N95-type masks manufactured to international standards; these include KN95 masks from China and FFP2 masks from the European Union. MethodsWe conducted a survey of mask in the inventory of major academic medical centers in Boston, MA to determine provenance and manufacturer. We then assembled a simple apparatus for performing a necessary (but not sufficient) test of filtration performance and tested masks from the inventory; an accompanying website shows how to build and use the testing apparatus. ResultsOur survey showed that, seven months after the start of the COVID-19 pandemic, over 100 different makes and models of N95-type masks are in the inventory of local hospitals as opposed to 2-5 models under normal circumstances. A substantial number of unfamiliar masks are from unknown manufacturers. Many did not perform to accepted standards and are likely to be counterfeit. Due to the absence of publicly available information on mask suppliers in the FDA EUA and confusing or inconsistent labeling of KN95 masks, it is difficult to distinguish legitimate and counterfeit products. ConclusionsMany of the FFR masks available for procurement during the COVID-19 pandemic do not provide levels of fit and filtration similar to those of N95 masks and are not acceptable for use in healthcare settings. Based on these results, and in consultation with occupational health officers, we make six recommendations for end users to assist in acquiring legitimate products. In particular, institutions should always assess masks from non-traditional supply chains by checking their markings and manufacturer information against data provided by NIOSH and the latest FDA EUA Appendix A. In the absence of verifiable information on the legitimacy of mask source, institutions should consider measuring mask fit and filtration directly. We also make suggestions for U.S and Chinese regulatory agencies with regard to labeling and public disclosure aimed at increase pandemic resilience.

3D Printed frames to enable reuse and improve the fit of N95 and KN95 respirators

BackgroundIn response to supply shortages during the COVID-19 pandemic, N95 filtering facepiece respirators (FFRs or "masks"), which are typically single-use devices in healthcare settings, are routinely being used for prolonged periods and in some cases decontaminated under "reuse" and "extended use" policies. However, the reusability of N95 masks is often limited by degradation or breakage of elastic head bands and issues with mask fit after repeated use. The purpose of this study was to develop a frame for N95 masks, using readily available materials and 3D printing, which could replace defective or broken bands and improve fit. ResultsAn iterative design process yielded a mask frame consisting of two 3D-printed side pieces, malleable wire links that users press against their face, and cut lengths of elastic material that go around the head to hold the frame and mask in place. Volunteers (n= 41; average BMI= 25.5), of whom 31 were women, underwent qualitative fit with and without mask frames and one or more of four different brands of FFRs conforming to US N95 or Chinese KN95 standards. Masks passed qualitative fit testing in the absence of a frame at rates varying from 48 - 92% (depending on mask model and tester). For individuals for whom a mask passed testing, 75-100% (average = 86%) also passed testing with a frame holding the mask in place. Among users for whom a mask failed in initial fit testing, 41% passed using a frame. Success varied with mask model and across individuals. ConclusionsThe use of mask frames can prolong the lifespan of N95 and KN95 masks by serving as a substitute for broken or defective bands without adversely affecting fit. Frames also have the potential to improve fit for some individuals who cannot fit existing masks. Frames therefore represent a simple and inexpensive way of extending the life and utility of PPE in short supply. For clinicians and institutions interested in mask frames, designs and specifications are provided without restriction for use or modification. To ensure adequate performance in clinical settings, qualitative fit testing with user-specific masks and frames is required.

Rapid prototyping and clinical testing of a reusable face shield for health care workers responding to the COVID-19 pandemic

Due to supply chain disruption, the COVID-19 pandemic has caused severe shortages in personal protective equipment (PPE) for health care professionals. Local fabrication based on 3D printing is one way to address this challenge, particularly in the case of simple products such as protective face shields. As a consequence, many public domain designs for face shields have become available. No clear path exists, however, for introducing a locally fabricated and unapproved product into a clinical setting. In a US health care setting, face shields are regulated by the Food and Drug Administration (FDA); similar policies exist in other countries. We describe a research protocol under which rapid iteration on an existing design, coupled with clinical feedback and real-world testing in an emergency department, allowed a face shield to be implemented by the members of the incident command team at a major academic medical center. We describe our design and testing process and provide an overview of regulatory considerations associated with fabrication and testing of face shields and related products. All designs, materials used, testing protocols, and survey results are reported in full to facilitate the execution of similar face shield efforts in other clinical settings. Our work serves as a case study for development of a robust local response to pandemics and other health care emergencies, with implications for healthcare professionals, hospital administrators, regulatory agencies and concerned citizens.