Management and incidence of tibial tubercle fractures in bicondylar fractures of the tibial plateau.

Bicondylar tibial plateau fractures result from high-energy injuries. Fractures of the tibial plateau can involve the tibial tubercle, which represents a disruption to the extensor mechanism and logically must be stabilised. The purpose of this study was to identify the incidence of an independent tibial tubercle fracture in bicondylar tibial plateau fractures, and to report management strategies and potential complications. We retrospectively reviewed a prospectively collected orthopaedic trauma database for the period January 2003 to December 2008, and identified 392 bicondylar fractures of the tibial plateau, in which 85 tibial tubercle fractures (21.6%) were identified in 84 patients. There were 60 men and 24 women in our study group, with a mean age of 45.4 years (18 to 71). In 84 fractures open reduction and internal fixation was undertaken, either with screws alone (23 patients) or with a plate and screws (61 patients). The remaining patient was treated non-operatively. In all, 52 fractures were available for clinical and radiological assessment at a mean follow-up of 58.5 weeks (24 to 94). All fractures of the tibial tubercle united, but 24 of 54 fractures (46%) required a secondary procedure for their tibial plateau fracture. Four patients reported pain arising from prominent tubercle plates and screws, which in one patient required removal. Tibial tubercle fractures occurred in over one-fifth of the bicondylar tibial plateau fractures in our series. Fixation is necessary and can be reliably performed with screws alone or with a screw and plate, which restores the extensor mechanism and facilitates early knee flexion.

The use of a locking custom contoured blade plate for peri-articular nonunions.

A retrospective chart and radiographic review was performed of 37 operative procedures over 7 years period for peri-articular nonunions. This was a consecutive cohort from a single orthopedic trauma service of a Level 1 center. Nonunions of the tibia and humerus were treated with blade plates fashioned from standard compression plates. Twenty-nine operative sites were treated successfully. The average age was 45.0 years; the average follow-up being 5.3 years. The average number of operations before blade plate was 4.0 (range 1-16). Sixteen blade plates were performed in patients with a diagnosis of clinical infection and all progressed to union and resolution of infection. Seven tissue transfers were used as adjunctive therapy. Five other patients with blade plate surgery had persistent nonunion, of which four united after a second custom contoured blade plate procedure. This study illustrates that surgeon contoured blade plates are an option for peri-articular nonunions even in the presence of infection. This technique resulted in a high union rate and a low complication rate compared to other options.

Deleterious effect of smoking on healing of open tibia-shaft fractures.

We retrospectively reviewed a prospectively followed cohort of 105 patients with 110 open tibia fractures treated with external fixator or intramedullary nail to determine whether smoking affects fracture healing. Severe open tibia-shaft fractures treated at a tertiary-care medical center were included. Patients with type II, IIIA, or IIIB tibia fractures were eligible. Treatment for all patients was similar, except that they were randomized to receive external fixator or intramedullary nail. Time to fracture healing was the main outcome measurement. Smokers had a union rate of 84% (52/62), and nonsmokers had a union rate of 94% (45/48), P = .10. For smokers in one arm of the study, time to union was significantly longer (P = .01), and there were more complications (P = .04). Smoking decreased unions, slowed healing, and increased complications.

Surgical treatment of olecranon fractures.

Fractures of the olecranon are common injuries with no single accepted treatment. Numerous clinical factors and biomechanical studies guide the surgeon in determining a treatment plan. The goals of surgical management include anatomical reduction and stable fixation, which allow early range of motion of the elbow joint. Numerous fixation methods have been described and include screw fixation, cerclage wiring, modified tension-band wiring, and plate fixation. The surgical technique depends on a combination of patient factors, the fracture pattern, and the mechanical stability of the fixation construct. Postoperative rehabilitation includes early active range-of-motion exercises and follows clinical and radiographic healing. Complications are related to the fracture, choice of implant, and surgical technique.

Trends in case-mix-adjusted use of radiology resources at an urban level 1 trauma center.

OBJECTIVE: The objective of our study was to determine the utilization rates of diagnostic radiology services at an urban level 1 trauma center. MATERIALS AND METHODS: This was an observational study of imaging use patterns from 1993 to 1998. Data were segregated by patient type and imaging procedure. Annual hospital admissions were adjusted for severity of illness using the Health Care Financing Administration's case-mix index. Per-patient imaging trends for the emergency department and outpatients were assessed using a ratio of the total number of procedures to the number of patient visits. Linear regression models were used to assess the strength of associations between resource use, measured as relative value units (RVUs), and independent variables (calendar year, patient type, and examination type). RESULTS: The RVUs for all imaging increased 53% for inpatients, 69% for outpatients, and 85% in the emergency department. No significant trend for use was found for the aggregate of inpatient imaging. There was a significant increase in the inpatient MR imaging RVUs (p = 0.04). No significant trend was found for the aggregated outpatient imaging RVUs. The trends were significant for angiography (p = 0.006), MR imaging (p = 0.002), and sonography (p = 0.04). The aggregated emergency room imaging RVUs showed a significant increase over time (p < 0.03). CONCLUSION: The number of imaging procedures increased during the study period. There was no overall trend toward increasing use of imaging in inpatients once an adjustment for severity of illness was made. Increases in patient visit-adjusted emergency department use of CT, sonography, and nuclear medicine procedures resulted from changes in practice patterns. For emergency department and outpatient settings, adjusting for the number of patient visits explains a significant portion of the increase in utilization.

The anterior T-frame external fixator for high-energy proximal tibial fractures.

The authors' experience using anterior T-frame external fixation combined with percutaneous internal fixation for treatment of high-energy proximal tibial fractures is reported. Thirty-six patients (38 fractures) were reviewed who were treated during a consecutive 42-month period. Three patients died and one patient had an amputation for a Type IIIC open injury, leaving 20 males and 12 females with 21 closed and 13 open fractures (two Type II, seven Type IIIA, three Type IIIB, and one Type IIIC). The average followup was 26 months. Fractures united at a mean of 20 weeks. Ten secondary surgical procedures were planned, including seven antibiotic bead removals with autogenous bone grafting and three soft tissue coverage procedures. Nine (26%) complications were found, including one deep infection (septic arthritis) and three pin tract infections, and one each malunion, nonunion, refracture, knee stiffness requiring manipulation under anesthesia, and deep venous thrombosis. The average Knee Society score was 85 for pain and 83 for function. All patients achieved full knee extension and mean flexion was 125 degrees. The anterior T-frame external fixator with percutaneous internal fixation is a reliable method to stabilize these injuries. It is simple, inexpensive, and effective.

Randomized prospective study of humeral shaft fracture fixation: intramedullary nails versus plates.

OBJECTIVES: To compare the clinical and radiographic results for locked intramedullary (IM) nails and plates used in the treatment of humeral diaphyseal fractures. DESIGN: Prospective randomization by sealed-envelope technique of eighty-four patients into two study groups: those treated by intramedullary nailing (IMN group; n = 38) and those treated by compression plating (PLT group; n = 46). SETTING: Patients admitted consecutively to a university-affiliated Level I trauma center. PATIENT/PARTICIPANTS: All skeletally mature patients admitted to Harborview Medical Center with acute humeral shaft fractures requiring surgical stabilization. Fractures of the diaphysis were defined as being at least three centimeters distal to the surgical neck and at least five centimeters proximal to the olecranon fossa. INTERVENTION: Treatment with locking antegrade intramedullary humeral nails (Russell-Taylor design [Smith and Nephew Richards]) or with 4.5-millimeter dynamic compression and limited contact dynamic compression plates (AO design [Synthes]). MAIN OUTCOME MEASUREMENTS: Clinical outcome measurements included fracture healing, radial nerve recovery, infection, and elbow and shoulder discomfort. Radiographic measurements included fracture alignment, time to healing, delayed union, and nonunion. RESULTS: Follow-up averaged thirteen months. Forty-two fractures (93 percent) in the PLT group were healed by sixteen weeks versus thirty-three fractures (87 percent) in the IMN group (p = 0.70). Shoulder pain and a decrement in shoulder range of motion (ROM) were significant associations with IMN (p = 0.007 for both variables) but not with PLT. A decrement in elbow ROM was significantly associated with PLT (p = 0.03), especially for fractures of the distal third of the diaphysis, whereas elbow pain was not (p = 0.123). The sum of other complications demonstrated nearly equal prevalence for both treatment groups. CONCLUSIONS: For patients requiring surgical treatment of a humeral shaft fracture, intramedullary nailing and compression plating both provide predictable methods for achieving fracture stabilization and ultimate healing.

The role of fixation of the fibula in open fractures of the tibial shaft with fractures of the ipsilateral fibula: indications and outcomes.

To determine the indications for fibular fixation in cases of combined fractures of the tibia and fibula and the effect of fibular fixation on tibial healing, a retrospective study of open fractures of the tibial shaft with concomitant fibula fractures was conducted at a level one trauma center. Apparent indications for fibular fixation included the presence of a syndesmotic injury and location of fracture within the distal third of the fibula. No significant differences were found in the healing rates, incidence of nonunion and malalignment, or in the number of required subsequent procedures between patients who did and did not undergo fibular stabilization. These results suggest that fixation of the fibula in open fractures of the tibia and fibula has no effect on fracture healing or alignment. A randomized, prospective study is needed to properly validate these findings.

Treatment of type II, IIIA, and IIIB open fractures of the tibial shaft: a prospective comparison of unreamed interlocking intramedullary nails and half-pin external fixators.

OBJECTIVE: To compare unreamed intramedullary nailing (IMN) with external fixation (EF) in patients with Type II, IIIA, and IIIB open fractures of the tibial shaft. DESIGN: An inception cohort of consecutive patients with Type II, IIIA, and IIIB tibial fractures incurred between January 1988 and March 1993 were systematically allocated into one of two treatment groups. Patients were treated and followed with a prospectively designed protocol. PATIENTS AND SETTING: All patients were skeletally mature and had incurred a fracture of the tibial diaphysis within twenty-four hours of presentation to the tertiary care hospital, a Level I Trauma Center. One hundred seventy-four fractures in 168 patients were stabilized with either IMN (104) or half-pin EF (70). There were 132 men and thirty-six women, with an average age of thirty-three years (range, 14 to 77 years). INTERVENTION: Except for the selection of the fixation device, open fracture care was similar in the two treatment groups. All patients underwent emergent irrigation and debridement with concomitant skeletal stabilization. Cephalosporin antibiotics were administered perioperatively for twenty-four to forty-eight hours. No wounds were closed primarily. Delayed primary closure, skin grafting, and/or myoplasty were performed between three and ten days after injury. MAIN OUTCOME MEASURES: The main outcome measures were final fracture alignment, presence of infection or inflammation, hardware failure, time to union, and the number of operative procedures. RESULTS: The IMN group had significantly fewer incidences of malalignment than did the EF group [8 vs. 31 percent; p = 0.00005; confidence interval (CI) = 0.18, 0.76] and had significantly fewer subsequent procedures (mean of 1.7 vs. mean of 2.7 per fracture; p = 0.001; CI = 0.45, 1.59). IMN resulted in fewer infections/ inflammatory problems than did EF at the injury site (13 vs. 21 percent; p = 0.73; CI = -0.63, 0.45) and significantly fewer at surgical interfaces (i.e., pin sites, nail and interlocking screw insertion sites; 2 vs. 50 percent; p = 0.000; CI = 0.39, 0.60). No significant difference was found in the healing rates for the two implant groups. The more severe Gustilo injury types had longer healing times regardless of the type of fixation. CONCLUSIONS: Results suggest that unreamed interlocking intramedullary nails are more efficacious than half-pin external fixators, in particular with regard to maintenance of limb alignment. However, the severity of soft tissue injury rather than the choice of implant appears to be the predominant factor influencing rapidity of bone healing and rate of injury site infection.

The role of fibular fixation in combined fractures of the tibia and fibula: a biomechanical investigation.

OBJECTIVES: To determine whether adjunctive plating of the fibula with tibial fixation enhanced the stability of the construct under combined compressive and bending loads in simulated fractures of both the tibia and fibula. METHODS: Each of twelve fresh cadaveric specimens (six pairs) with an intact knee, lower extremity, and foot was mounted on the table of a materials testing machine. An intramedullary (IM) rod locked in the distal femur allowed combined compression, and flexion, valgus bending, or varus bending loads to be transmitted from the actuator of the testing machine to the knee. Three displacement measurement transducers were mounted on the tibia at anterior, posterolateral, and posteromedial positions. Intact tibial deformations under load were measured. Then, in one specimen of each pair a 2 cm osteotomy was created near the tibial midshaft, which was stabilized with an external fixator. Tibial gap displacements were measured under the following conditions: (a) intact fibula, (b) osteotomized fibula, (c) fibula fixed with a plate, (d) fibula fixed with an Enders IM nail. In the other specimen of the pair, tibial fixation was performed with an interlocked unreamed IM nail, with the same successive stages of fibular fixation. RESULTS: Osteotomy of the fibula significantly increased tibial defect motion when external fixation was used, and plating the fibula in this case significantly decreased motion. Using an Enders rod to stabilize the fibula instead of a plate, with tibial external fixation, produced smaller decreases in tibial defect site motion. With IM rod fixation of the tibia, osteotomizing the fibula had no effect on defect site motion or on its subsequent stabilization using a plate or IM rod. CONCLUSION: Plating the fibula can decrease motion across a tibial defect, but only when less rigid (i.e., external) fixation is used.

A biomechanical comparison of two methods of fixation of fractures of the forearm.

In this study two different types of forearm internal fracture fixations were compared: limited-contact dynamic compression (DC) plates and fluted intramedullary (IM) rods. Eight matched pairs of intact forearms, consisting of the distal part of the humerus, elbow joint, radius, ulna, interosseus membrane, wrist joint, and metacarpals, were randomly separated into two groups. Each was placed into a custom-designed apparatus and subjected to medial bending, supination, pronation, axial compression, and distraction loading. Loads were applied by a materials testing system, and angular displacements were measured by inclinometers. The procedure consisted of first testing specimens intact, then retesting after osteotomizing and fixing the radius with either a plate or rod in half of the group and retesting after osteotomizing and fixing the ulna in the other half. Testing was continued by osteotomizing and remaining intact bone to create a two-bone fracture, fixing them, and retesting after creating a 5-mm gap at the osteotomy sites. These tests showed that the intact ulna contributes more to forearm stability in bending and torsion than does the radius. Therefore, if the radius is fractured but the ulna remains intact, IM rodding will produce constructs with greater stiffnesses, particularly in torsion, than if the ulna is fractured and the radius is intact. In the case of a two-bone fracture, implantation of rods will result in a construct with significantly less stiffness in torsion, as well as distraction and compression (in the case of a fracture gap), than if the fractures were plated.(ABSTRACT TRUNCATED AT 250 WORDS)

A comparison of malreduction after plate and intramedullary nail fixation of forearm fractures.

A study was performed to compare the degree of malreduction after intramedullary nail and plate fixation of the forearm and to determine if the degree of malreduction was clinically significant. Eight matched pairs of forearms, including the wrist and elbow joints, were harvested from cadaver upper extremities. The forearms were put through a full range of motion, and physiological loads were applied to simulate those during normal use. Standardized anteroposterior and lateral radiographs of each forearm were obtained with the specimen intact, and after an osteotomy and internal fixation of one bone, both bones, and with gap at the osteotomy sites. In each forearm pair, plating was randomly performed in one specimen and intramedullary nailing was performed in the matching contralateral specimen. Forearm architecture was assessed by quantification of the magnitude and location of maximum radial bow and radial angulation. In this study, plate fixation was superior to nail stabilization in restoration of the normal radial architecture. Plating did not change any of the radiographic indices (magnitude and location of maximum radial bow and radial angulation) at any stage of testing. None of the radiographic indices was changed by nailing of only one of the forearm bones. The magnitude of maximum radial bow and the radial angulation were changed by nailing both forearm bones after osteotomy and both forearm bones with a gap (p < 0.05). Despite this, both techniques were well within the limits of what is radiographically acceptable for reduction.(ABSTRACT TRUNCATED AT 250 WORDS)

Biomechanical evaluation of methods of internal fixation of the distal humerus.

The best results following fractures of the distal humerus are provided by anatomic reduction and rigid internal fixation. Plates of two designs placed in five different fixation configurations were used to determine the construct that would maximize rigidity of fixation of the distal humerus. Using a cadaver distal humerus osteotomy, with and then without cortical contact, motion of the distal fragment was measured with respect to the proximal fragment in axial and torsional loading, anterior to posterior and posterior to anterior bending, and lateral to medial and medial to lateral bending. With cortical contact, two plates when placed medial and lateral or at 90 degrees to each other provided equivalent rigidity. However, with a cortical gap, the combination of a specially designed anatomic lateral buttress "J" plate and a medial reconstruction plate gave the greatest rigidity (ANOVA, p < 0.05). Two-plate constructs do not require placement at 90 degrees to obtain sufficient rigidity, but do require placement on separate bony pillars and different surfaces.

Removal of broken syndesmotic screws: a technical tip.

A simple method of extracting broken distal tibial-fibular syndesmotic or cross-locking screws for intramedullary nails is illustrated. After extraction of the head portion of the broken screw, a blunt impactor is introduced through the vacant screw hole and abutted to the remaining portion of the screw tip. The screw can usually be impacted through the far cortex. A small incision should be made over the protruding portion, and the screw extracted with pliers.

A comparison of transferred versus direct admission orthopedic trauma patients.

Trauma patients with orthopedic injuries transferred to Harborview Medical Center (HMC) were compared with all trauma patients directly admitted to HMC and with a set of matched controls regarding injury Severity Score (ISS) and age, if > or = 50 years old. Groups were compared on ISS, Revised Trauma Score (RTS), ICU stay, length of stay (LOS), total charges, reimbursement, payors, and outcome. Comparison of all transferred patients and directly admitted patients showed significant differences in ISS, LOS, ICU stay, and total charges. Despite a higher ISS, transferred patients had no differences in RTS or survival outcome. Comparison of matched transferred patients and directly admitted patients on ISS and age if > or = 50 years old showed a statistically significant increase in LOS, reimbursement, and charges. The survival rate of all transferred and directly admitted trauma patients was approximately 95% for both groups despite a slightly higher degree of injury in transferred patients. The reimbursement rate for both groups was low, 65% for transferred patients and 59% for directly admitted patients. The percentage of transfer patients on Medicaid was 34% and for direct admissions was 37% (p = 0.552). This is a large percentage of indigent care, since only 8.1% of Washington State residents are Medicaid dependent.

Fixation with bioabsorbable screws for the treatment of fractures of the ankle.

One hundred and fifty-five patients who had a closed, displaced medial malleolar, bimalleolar, or trimalleolar fracture of the ankle were managed with medial malleolar fixation with use of either 4.0-millimeter orientruded polylactide screws (eighty-three patients, study group) or 4.0-millimeter stainless-steel screws (seventy-two patients, control group). All lateral malleolar fractures were stabilized with standard metallic implants. At an average of thirty-seven months (range, twenty-one to fifty-nine months), the radiographic and functional results in the two groups were equivalent. Differences between the two groups with regard to the rates of operative and postoperative complications were not statistically significant. Late spontaneous drainage of the hydrolyzed polylactide was not noted in any patient in the study group. The prevalence of late tenderness over the medial malleolar implant was lower in the patients in whom the fracture had been stabilized with polylactide screws. We conclude that polylactide screws are a safe and effective alternative to stainless-steel screws for the fixation of displaced medial malleolar fractures.

Biomechanical effects of internal fixation of the distal tibiofibular syndesmotic joint: comparison of two fixation techniques.

This biomechanical study compares two methods of internal fixation of the tibiofibular syndesmosis used in Weber type C malleolar fractures of the ankle. The transverse syndesmotic 3.5-mm screw was compared with two 1.5-mm Kirschner wires introduced obliquely across the distal tibiofibular syndesmosis. The influence of implants on distal tibiofibular joint motion and contact characteristics of the intact ankle joint were determined. Up to 1.25 mm of lateral displacement and 2 degrees of external rotation of the lateral malleolus during uninjured ankle dorsiflexion was recorded. Both techniques stabilized the injured syndesmotic joint and limited its normal motion during flexion and extension of the ankle. Pressure distribution displaced laterally in internally stabilized ankles compared with intact specimens, regardless of the type of fixation used. Therefore, both techniques alter joint biomechanics equivalently compared with the intact ankle.

Early stabilization and decompression for incomplete paraplegia due to a thoracic-level spinal cord injury.

All patients treated between 1985 and 1990 for acute incomplete spinal cord injury between T2 and T11 were retrospectively studied. This level was chosen for study because by excluding cervical cord, conus, and cauda equina injuries, neurologic improvement could be attributed to improvement of spinal cord function. Only 14 patients with incomplete thoracic level paraplegia were identified, representing 1.2% of all spinal injuries. All 14 patients were treated by early operative reduction, stabilization, or decompression. Twelve patients had surgery within 24 hours of neurologic injury, one at 36 hours, and one at 5 days. Twelve patients had initial posterior instrumentation and fusion, one of whom subsequently had an anterior decompression. Two patients had initial anterior decompression and fusion. Both later had posterior instrumentation and fusion to treat progressive deformity. Follow-up averaged 20 months (range, 9-65 months). Neural function before surgery and at follow-up was given a Frankel grade and lower extremity motor index score. Of 13 surviving patients, seven were initially Frankel B and six Frankel C. Of the seven patients initially Frankel B, four recovered to Frankel E, two improved to Frankel D, and one remained Frankel B. Of the six patients originally Frankel C, five recovered to Frankel E and one improved to Frankel D. Average neurologic improvement was 2.2 Frankel grades per patient, lower extremity motor index improved from an average of 7 to 44. Early surgical reduction, stabilization, and decompression is safe and improves neurologic recovery in comparison to historical controls treated by postural reduction or late surgical intervention.

Closed interlocking nailing of femoral shaft fractures: assessment of technical complications and functional outcomes by comparison of a prospective database with retrospective review.

Although closed interlocking femoral nailing is generally considered to be a difficult but effective procedure, the true incidence of technical complications has not been well documented. Similarly, long-term and functional patient-oriented data are limited. We reviewed our experience with an interlocking nail system that was introduced in our institution in October 1987. One hundred and twenty-three patients were retrospectively reviewed with particular attention to technical complications (Group I). A second group of 144 patients with femoral shaft fractures were reviewed prospectively as a part of our Orthopaedic Trauma Outcome Database (Group IIA). In the earlier retrospective group, the technical complications in 123 cases included one distal screw fracture, one broken drill bit left (in situ), one "missed" locking distal screw, and three cases where comminution at the fracture site was increased. In the prospective group of 144 fractures, the technical complications included two "missed" distal locking screws, two broken screws, and one bent nail due to additional secondary trauma. In a third group of 56 patients (Group IIB) selected from Group IIA, an abbreviated functional assessment was performed at a minimum of 12 months postinjury. Of this group, 37% of the patients had pain that was described as related to barometric changes and was either constant or activity related; 39% had some limitation in ability to ambulate or stand. Nine percent had to obtain new employment or seek job modifications. Based on our data we conclude that closed intramedullary nailing can be done at a Level I Trauma Center with relatively few technical complications, but the functional outcomes are not as good as had been previously believed.(ABSTRACT TRUNCATED AT 250 WORDS)