Efficiency enhancement of perovskite solar cells based on opal-like photonic crystals.

Perovskite solar cells have shown a tremendous interest for photovoltaics since the past decade. However, little is known on the influence of light management using photonic crystals inside such structures. We present here numerical simulations showing the effect of photonic crystal structuring on the integrated quantum efficiency of perovskite solar cells. The photo-active layer is made of an opal-like perovskite structure (monolayer, bilayer or trilayer of perovskite spheres) built in a T i O 2 matrix. Fano resonances are exploited in order to enhance the absorption, especially near the bandgap of perovskite material. The excitation of quasi-guided modes inside the absorbing spheres enhances the integrated quantum efficiency and the photonic enhancement factor. More specifically, a photonic enhancement factor as high as 6.4% is predicted in the case of spheres monolayer compared to an unstructured perovskite layer. The influences of sphere's radius and incident angle on the absorbing properties are also estimated. Those numerical results can be applied to the nascent field of photonic structuring inside perovskite solar cells.

Chitosan enriched three-dimensional matrix reduces inflammatory and catabolic mediators production by human chondrocytes.

This in vitro study investigated the metabolism of human osteoarthritic (OA) chondrocytes encapsulated in a spherical matrix enriched of chitosan. Human OA chondrocytes were encapsulated and cultured for 28 days either in chitosan-alginate beads or in alginate beads. The beads were formed by slowly passing dropwise either the chitosan 0.6%-alginate 1.2% or the alginate 1.2% solution through a syringe into a 102 mM CaCl2 solution. Beads were analyzed histologically after 28 days. Interleukin (IL)-6 and -8, prostaglandin (PG) E2, matrix metalloproteinases (MMPs), hyaluronan and aggrecan were quantified directly in the culture supernatant by specific ELISA and nitric oxide (NO) by using a colorimetric method based on the Griess reaction. Hematoxylin and eosin staining showed that chitosan was homogeneously distributed through the matrix and was in direct contact with chondrocytes. The production of IL-6, IL-8 and MMP-3 by chondrocytes significantly decreased in chitosan-alginate beads compared to alginate beads. PGE2 and NO decreased also significantly but only during the first three days of culture. Hyaluronan and aggrecan production tended to increase in chitosan-alginate beads after 28 days of culture. Chitosan-alginate beads reduced the production of inflammatory and catabolic mediators by OA chondrocytes and tended to stimulate the synthesis of cartilage matrix components. These particular effects indicate that chitosan-alginate beads are an interesting scaffold for chondrocytes encapsulation before transplantation to repair cartilage defects.

Varying TiO2 macroscopic fiber morphologies toward tuning their photocatalytic properties.

In a context of volatile organic compound photodecomposition, we have addressed TiO2-based macroscoscpic fiber generation. We have extruded hybrid sols of amorphous titania nanoparticles, latex nanoparticles, and nonionic surfactant (Tergitol) as structure-directing agents into a poly(vinyl alcohol) (PVA) solution bearing salts acting as a flocculating medium. The resulting nanocomposite TiO2/latex/PVA macroscopic fibers were thermally treated in air to open porosity by organic removal while generating the photocatalytically active anatase phase of TiO2 along with residual brookite. Considering the synthetic paths, we have varied both the diameter of the latex particles as well as their concentration within the starting sol. These parameters allow tuning both the voids created through the applied thermal treatment and the fiber final diameters. For gas-phase photocatalysis, we have shown that the fiber diameters, mesoscopic roughness, and macroscopic topological defects represent indeed important morphological parameters acting cooperatively toward both acetone degradation and its mineralization processes. Particularly, triggering the fiber morphological characteristics, we have increased their efficiency toward acetone degradation of around 550% when compared with previous work.

Morphological and opto-electrical properties of a solution deposited platinum counter electrode for low cost dye sensitized solar cells.

Although platinum (Pt) is a rare and very expensive material, Pt counter electrodes are still very commonly used for reaching high efficiencies in dye-sensitized solar cells (DSCs). The use of alternative cheaper catalyst materials did not yet yield equivalent efficiencies. In this work, we tried to understand how to reduce the amount of deposited Pt-material and simultaneously deliver higher DSC performances. We systematically compared the properties of Pt-counter electrodes prepared by simple solution deposition methods such as spray-coating, dip-coating, brushing with reference to the Pt-electrodes prepared by sputtering onto fluorine doped-tin oxides (FTOs). The morphological and structural characterizations of the deposited Pt-layers were performed by atomic force microscopy (AFM) and scanning electron microscopy (SEM). The composition of Pt-material was quantified using SEM electron dispersive X-ray (EDX) mapping measurements which were further compared with optical transmission measurements. Also contact angle and sheet resistance measurements were performed. By taking Pt-layers composition, morphology and structural factors into account, 9.16% efficient N3 dye based DSCs were assembled. The DSCs were subjected to various opto-electrical characterization techniques like current-voltage (I-V), external quantum efficiency (EQE), cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS) and transient photo voltage (TPV) measurements. The obtained experimental data suggest that the Pt counter electrodes prepared by solution deposition methods can also reach high DSC device performances with a consumption of very little amount of Pt material as compared with sputtered Pt-layers. This process also proves that higher DSC performances are not limited to the usage of sputtered Pt-layer as counter electrode.

Experimental design applied to spin coating of 2D colloidal crystal masks: a relevant method?

Monolayers of colloidal spheres are used as masks in nanosphere lithography (NSL) for the selective deposition of nanostructured layers. Several methods exist for the formation of self-organized particle monolayers, among which spin coating appears to be very promising. However, a spin coating process is defined by several parameters like several ramps, rotation speeds, and durations. All parameters influence the spreading and drying of the droplet containing the particles. Moreover, scientists are confronted with the formation of numerous defects in spin coated layers, limiting well-ordered areas to a few micrometers squared. So far, empiricism has mainly ruled the world of nanoparticle self-organization by spin coating, and much of the literature is experimentally based. Therefore, the development of experimental protocols to control the ordering of particles is a major goal for further progress in NSL. We applied experimental design to spin coating, to evaluate the efficiency of this method to extract and model the relationships between the experimental parameters and the degree of ordering in the particles monolayers. A set of experiments was generated by the MODDE software and applied to the spin coating of latex suspension (diameter 490 nm). We calculated the ordering by a homemade image analysis tool. The results of partial least squares (PLS) modeling show that the proposed mathematical model only fits data from strictly monolayers but is not predictive for new sets of parameters. We submitted the data to principal component analysis (PCA) that was able to explain 91% of the results when based on strictly monolayered samples. PCA shows that the ordering was positively correlated to the ramp time and negatively correlated to the first rotation speed. We obtain large defect-free domains with the best set of parameters tested in this study. This protocol leads to areas of 200 µm(2), which has never been reported so far.

Hybrid lamellar silica: combined template extraction and hydrophilic silanation.

The surface modification of lamellar silica prepared by liquid crystal templating has been investigated. Two hydrophilic surface modifier agents, 2-glycidoxypropyltrimethoxysilane and 2-[methoxy(polyethyleneoxy)propyl)]trimethoxysilane, have been tested. Characterizations of the modified silica include thermal analysis, (13)C and (29)Si solid state NMR, transmission electron microscopy (TEM) and X-ray diffraction (XRD). The different characterizations confirmed the preservation of the lamellar morphology and the successful surface modification with both silanes along with the template elimination. The results also indicate that the structure and length of the silanes influence the final lamellar organization as well as the grafting yields and mechanisms.

Otolith crystals (in Carapidae): growth and habit.

The biomineralization of otoliths results mainly from the release of soluble Ca(2+), which is in turn precipitated as CaCO(3) crystals. In some Carapidae, sagittae sections have been shown to reveal a three-dimensional asymmetry with a nucleus close to the sulcal side, an unusual position. This study seeks to understand otolith formation in Carapus boraborensis. The unusual shape of the otolith is partly explained by the distribution of the epithelium cells, and particularly the sensory epithelium. Experimental evidence shows for the first time that aragonite growth takes place along the c-axis. These aragonite needles present two different habits. On the sulcal side is found the acicular form resulting from rapid growth during a short period of time. On the anti-sulcal side, the prismatic form seen there is due to a slower growth speed over longer periods. The otolith surface was observed each hour during a period of 24h in fishes reared in similar conditions. This allowed for the first time the direct observation on the otolith surface of the deposition of the two layers (L-zone and D-zone). In C. boraborensis, the organic-rich layer (D-zone) develops during the day, whereas the CaCO(3) layer (L-zone) seems to be deposited during the night.