Long distance laser filamentation using Yb:YAG kHz laser.

In the framework of the Laser Lightning Rod project, whose aim is to show that laser-induced filaments can guide lightning discharges over considerable distances, we study over a distance of 140 m the filaments created by a laser system with J-range pulses of 1 ps duration at 1 kHz repetition rate. We investigate the spatial evolution of the multiple filamentation regime using the fundamental beam at 1030 nm or using combination with the second and third harmonics. The measurements were made using both a collimated beam and a loosely focused beam.

Laser-guided lightning.

Lightning discharges between charged clouds and the Earth's surface are responsible for considerable damages and casualties. It is therefore important to develop better protection methods in addition to the traditional Franklin rod. Here we present the first demonstration that laser-induced filaments-formed in the sky by short and intense laser pulses-can guide lightning discharges over considerable distances. We believe that this experimental breakthrough will lead to progress in lightning protection and lightning physics. An experimental campaign was conducted on the Säntis mountain in north-eastern Switzerland during the summer of 2021 with a high-repetition-rate terawatt laser. The guiding of an upward negative lightning leader over a distance of 50 m was recorded by two separate high-speed cameras. The guiding of negative lightning leaders by laser filaments was corroborated in three other instances by very-high-frequency interferometric measurements, and the number of X-ray bursts detected during guided lightning events greatly increased. Although this research field has been very active for more than 20 years, this is the first field-result that experimentally demonstrates lightning guided by lasers. This work paves the way for new atmospheric applications of ultrashort lasers and represents an important step forward in the development of a laser based lightning protection for airports, launchpads or large infrastructures.

Ultrafast thin-disk multipass amplifier with 720 mJ operating at kilohertz repetition rate for applications in atmospheric research.

We present an ultrafast thin-disk based multipass amplifier operating at a wavelength of 1030 nm, designed for atmospheric research in the framework of the Laser Lightning Rod project. The CPA system delivers a pulse energy of 720 mJ and a pulse duration of 920 fs at a repetition rate of 1 kHz. The 240 mJ seed pulses generated by a regenerative amplifier are amplified to the final energy in a multipass amplifier via four industrial thin-disk laser heads. The beam quality factor remains ∼ 2.1 at the output. First results on horizontal long-range filament generation are presented.

Parallel gas spectroscopy using mid-infrared supercontinuum from a single Si3N4 waveguide.

Efficient third-order nonlinear optical processes have been successfully integrated on silicon nitride (Si3N4) waveguides. In particular, owing to Si3N4 wide transparency window spanning from the visible to the middle-infrared (mid-IR), efficient mid-IR dispersive-wave (DW) generation from a fiber laser has been recently demonstrated, and its potential as a source for absorption spectroscopy of a single gas has been established. Here we show that the system can be further engineered to broaden the coverage of a single DW without losing efficiency, as to enable simultaneous and discrete detection of several gas-phase molecules within the 2900 and 3380cm-1 functional group region. We demonstrate quantitative detection of acetylene, methane, and ethane using a simple direct-absorption spectroscopy scheme, achieving a several hundreds of parts-per-million noise-equivalent detection limit with a 5 cm long gas cell.

HV discharges triggered by dual- and triple-frequency laser filaments.

We study the use of frequency upconversion schemes of near-IR picosecond laser pulses and compare their ability to guide and trigger electric discharges through filamentation in air. Upconversion, such as Second Harmonic Generation, is favorable for triggering electric discharges for given amount of available laser energy, even taking into account the losses inherent to frequency conversion. We focus on the practical question of optimizing the use of energy from a given available laser system and the potential advantage to use frequency conversion schemes.

Mid infrared gas spectroscopy using efficient fiber laser driven photonic chip-based supercontinuum.

Directly accessing the middle infrared, the molecular functional group spectral region, via supercontinuum generation processes based on turn-key fiber lasers offers the undeniable advantage of simplicity and robustness. Recently, the assessment of the coherence of the mid-IR dispersive wave in silicon nitride (Si3N4) waveguides, pumped at telecom wavelength, established an important first step towards mid-IR frequency comb generation based on such compact systems. Yet, the spectral reach and efficiency still fall short for practical implementation. Here, we experimentally demonstrate that large cross-section Si3N4 waveguides pumped with 2 µm fs-fiber laser can reach the important spectroscopic spectral region in the 3-4 µm range, with up to 35% power conversion and milliwatt-level output powers. As a proof of principle, we use this source for detection of C2H2 by absorption spectroscopy. Such result makes these sources suitable candidate for compact, chip-integrated spectroscopic and sensing applications.

Double inverse nanotapers for efficient light coupling to integrated photonic devices.

Efficient light coupling to integrated photonic devices is of key importance to a wide variety of applications. "Inverse nanotapers" are widely used, in which the waveguide width is reduced to match an incident mode. Here, we demonstrate novel "double inverse" tapers, in which we reduce both the waveguide height and width. We demonstrate >45% chip-through coupling efficiency for both the transverse electric and transverse magnetic polarizations in Si3N4 tapers of >500 nm width, in comparison to regular inverse tapers that necessitate <100 nm width. The double inverse tapers show polarization-independent coupling and allow the fabrication using photolithography, relevant for applications at near-infrared and visible wavelengths, e.g., supercontinuum and soliton microcomb generation.