Removal of Surface Oxygen Vacancies Increases Conductance Through TiO2 Thin Films for Perovskite Solar Cells.

We report that UV-ozone treatment of TiO2 anatase thin films is an efficient method to increase the conductance through the film by more than 2 orders of magnitude. The increase in conductance is quantified via conductive scanning force microscopy on freshly annealed and UV-ozone-treated TiO2 anatase thin films on fluorine-doped tin oxide substrates. The increased conductance of TiO2 anatase thin films results in a 2% increase of the average power conversion efficiency (PCE) of methylammonium lead iodide-based perovskite solar cells. PCE values up to 19.5% for mesoporous solar cells are realized. The additional UV-ozone treatment results in a reduced number of oxygen vacancies at the surface, inferred from X-ray photoelectron spectroscopy. These oxygen vacancies at the surface act as charge carrier traps and hinder charge extraction from the adjacent material. Terahertz measurements indicate only minor changes of the bulk conductance, which underlines the importance of UV-ozone treatment to control surface-based defects.

The Interplay of Contact Layers: How the Electron Transport Layer Influences Interfacial Recombination and Hole Extraction in Perovskite Solar Cells.

Charge-selective contact layers in perovskite solar cells influence the current density-voltage hysteresis, an effect related to ion migration in the perovskite. As such, fullerene-based electron transport layers (ETLs) suppress hysteresis by reducing the mobile ion concentration. However, the impact of different ETLs on the electronic properties of other constituent device layers remains unclear. In this Kelvin probe force microscopy study, we compared potential distributions of methylammonium lead iodide-based solar cells with two ETLs (planar TiO2 and C60-functionalized self-assembled monolayer) with different hysteretic behavior. We found significant changes in the potential distribution of the organic hole transport layer spiroMeOTAD, suggesting the formation of a neutral spiroMeOTAD/iodide interface due to a reaction between iodide with p-doped spiroMeOTAD in the TiO2 cell. Our results show that the ETL affects not only the mobile ion concentration and the recombination at the perovskite/ETL interface but also the resistance and capacitance of the spiroMeOTAD.

Know your full potential: Quantitative Kelvin probe force microscopy on nanoscale electrical devices.

In this study we investigate the influence of the operation method in Kelvin probe force microscopy (KPFM) on the measured potential distribution. KPFM is widely used to map the nanoscale potential distribution in operating devices, e.g., in thin film transistors or on cross sections of functional solar cells. Quantitative surface potential measurements are crucial for understanding the operation principles of functional nanostructures in these electronic devices. Nevertheless, KPFM is prone to certain imaging artifacts, such as crosstalk from topography or stray electric fields. Here, we compare different amplitude modulation (AM) and frequency modulation (FM) KPFM methods on a reference structure consisting of an interdigitated electrode array. This structure mimics the sample geometry in device measurements, e.g., on thin film transistors or on solar cell cross sections. In particular, we investigate how quantitative different KPFM methods can measure a predefined externally applied voltage difference between the electrodes. We found that generally, FM-KPFM methods provide more quantitative results that are less affected by the presence of stray electric fields compared to AM-KPFM methods.

Evidence of Tailoring the Interfacial Chemical Composition in Normal Structure Hybrid Organohalide Perovskites by a Self-Assembled Monolayer.

Current-voltage hysteresis is a major issue for normal architecture organo-halide perovskite solar cells. In this manuscript we reveal a several-angstrom thick methylammonium iodide-rich interface between the perovskite and the metal oxide. Surface functionalization via self-assembled monolayers allowed us to control the composition of the interface monolayer from Pb poor to Pb rich, which, in parallel, suppresses hysteresis in perovskite solar cells. The bulk of the perovskite films is not affected by the interface engineering and remains highly crystalline in the surface-normal direction over the whole film thickness. The subnanometer structural modifications of the buried interface were revealed by X-ray reflectivity, which is most sensitive to monitor changes in the mass density of only several-angstrom thin interfacial layers as a function of substrate functionalization. From Kelvin probe force microscopy study on a solar cell cross section, we further demonstrate local variations of the potential on different electron-transporting layers within a solar cell. On the basis of these findings, we present a unifying model explaining hysteresis in perovskite solar cells, giving an insight into one crucial aspect of hysteresis for the first time and paving way for new strategies in the field of perovskite-based opto-electronic devices.

Local Time-Dependent Charging in a Perovskite Solar Cell.

Efficient charge extraction within solar cells explicitly depends on the optimization of the internal interfaces. Potential barriers, unbalanced charge extraction, and interfacial trap states can prevent cells from reaching high power conversion efficiencies. In the case of perovskite solar cells, slow processes happening on time scales of seconds cause hysteresis in the current-voltage characteristics. In this work, we localized and investigated these slow processes using frequency-modulation Kelvin probe force microscopy (FM-KPFM) on cross sections of planar methylammonium lead iodide (MAPI) perovskite solar cells. FM-KPFM can map the charge density distribution and its dynamics at internal interfaces. Upon illumination, space charge layers formed at the interfaces of the selective contacts with the MAPI layer within several seconds. We observed distinct differences in the charging dynamics at the interfaces of MAPI with adjacent layers. Our results indicate that more than one process is involved in hysteresis. This finding is in agreement with recent simulation studies claiming that a combination of ion migration and interfacial trap states causes the hysteresis in perovskite solar cells. Such differences in the charging rates at different interfaces cannot be separated by conventional device measurements.