Efficient passivation of n-type and p-type silicon surface defects by hydrogen sulfide gas reaction.

An efficient surface defect passivation is observed by reacting clean Si in a dilute hydrogen sulfide-argon gas mixture (<5% H2S in Ar) for both n-type and p-type Si wafers with planar and textured surfaces. Surface recombination velocities of 1.5 and 8 cm s-1are achieved on n-type and p-type Si wafers, respectively, at an optimum reaction temperature of 550 °C that are comparable to the best surface passivation quality used in high efficiency Si solar cells. Surface chemical analysis using x-ray photoelectron spectroscopy shows that sulfur is primarily bonded in a sulfide environment, and synchrotron-based soft x-ray emission spectroscopy of the adsorbed sulfur atoms suggests the formation of S-Si bonds. The sulfur surface passivation layer is unstable in air, attributed to surface oxide formation and a simultaneous decrease of sulfide bonds. However, the passivation can be stabilized by a low-temperature (300 °C) deposited amorphous silicon nitride (a-Si:NX:H) capping layer.

Local electronic structure of the peptide bond probed by resonant inelastic soft X-ray scattering.

The local valence orbital structure of solid glycine, diglycine, and triglycine is studied using soft X-ray emission spectroscopy (XES), resonant inelastic soft X-ray scattering (RIXS) maps, and spectra calculations based on density-functional theory. Using a building block approach, the contributions of the different functional groups of the peptides are separated. Cuts through the RIXS maps furthermore allow monitoring selective excitations of the amino and peptide functional units, leading to a modification of the currently established assignment of spectral contributions. The results thus paint a new-and-improved picture of the peptide bond, enhance the understanding of larger molecules with peptide bonds, and simplify the investigation of such molecules in aqueous environment.

Site-specific electronic structure of imidazole and imidazolium in aqueous solutions.

The occupied and unoccupied electronic structure of imidazole (C3N2H4) and imidazolium (C3N2H5+) in aqueous solutions is studied by X-ray emission spectroscopy (XES) and resonant inelastic soft X-ray scattering (RIXS). Both systems show distinct RIXS fingerprints with strong resonant effects. A comparison with calculated X-ray emission spectra of isolated imidazole and imidazolium suggests only a small influence of hydrogen bonding in the aqueous solution on the electronic structure of imidazole and imidazolium, and allows the attribution of specific spectral features to the non-equivalent nitrogen and carbon atoms in the molecules. In the case of nitrogen, this can also be achieved by site-selective resonant excitation. Furthermore, we find spectator shifts and symmetry selectivity in the RIXS spectra, as well as indications for rapid proton dynamics on the femtosecond timescale of the RIXS process, and derive the HOMO-LUMO gaps for the two molecules in aqueous solution.

X-ray Emission Spectroscopy of Proteinogenic Amino Acids at All Relevant Absorption Edges.

Nonresonant N K, O K, C K, and S L2,3 X-ray emission spectra of the 20 most common proteinogenic amino acids in their solid zwitterionic form are reported. They represent a comprehensive database that can serve as a reliable basis for the X-ray absorption spectroscopy (XES) studies of peptides and proteins. At the most important N and O K edges, clear similarities and differences between the spectra of certain amino acids are observed and associated with the specific chemical structure of these molecules and their functional groups. Analysis of these spectra allows the generation of spectral fingerprints of the protonated amino group, the deprotonated carboxylic group, and, using a building block approach, the specific nitrogen- and oxygen-containing functional groups in the side chains of the amino acids. Some of these fingerprints are compared to the spectra of reference compounds with the respective functional groups; they exhibit reasonable similarity, underlining the validity of the spectral fingerprint approach. The C K and S L2,3 XES spectra are found to be specific for each amino acid, in accordance with the different local environments of the involved C and S atoms, respectively.

Investigation of the Ionic Hydration in Aqueous Salt Solutions by Soft X-ray Emission Spectroscopy.

Understanding the molecular structure of the hydration shells and their impact on the hydrogen bond (HB) network of water in aqueous salt solutions is a fundamentally important and technically relevant question. In the present work, such hydration effects were studied for a series of representative salt solutions (NaCl, KCl, CaCl2, MgCl2, and KBr) by soft X-ray emission spectroscopy (XES) and resonant inelastic soft X-ray scattering (RIXS). The oxygen K-edge XES spectra could be described with three components, attributed to initial state HB configurations in pure water, water molecules that have undergone an ultrafast dissociation initiated by the X-ray excitation, and water molecules in contact with salt ions. The behavior of the individual components, as well as the spectral shape of the latter component, has been analyzed in detail. In view of the role of ions in such effects as protein denaturation (i.e., the Hofmeister series), we discuss the ion-specific nature of the hydration shells and find that the results point to a predominant role of anions as compared to cations. Furthermore, we observe a concentration-dependent suppression of ultrafast dissociation in all salt solutions, associated with a significant distortion of intact HB configurations of water molecules facilitating such a dissociation.

Isotope Effects in the Resonant Inelastic Soft X-ray Scattering Maps of Gas-Phase Methanol.

The electronic structure of gas-phase methanol molecules (H3COH, H3COD, and D3COD) at atmospheric pressure was investigated using resonant inelastic soft X-ray scattering (RIXS) at the O K and C K edges. We observe strong changes of the relative emission intensities of all valence orbitals as a function of excitation energy, which can be related to the symmetries of the involved orbitals causing an angularly anisotropic RIXS intensity. Furthermore, all observed emission lines are subject to strong spectator shifts of up to -0.9 eV at the O K edge and up to -0.3 eV at the C K edge. At the lowest O K resonance, we find clear evidence for dissociation of the methanol molecule on the time scale of the RIXS process, which is illustrated by comparing X-ray emission spectra of regular and deuterated methanol.

Probing hydrogen bonding orbitals: resonant inelastic soft X-ray scattering of aqueous NH3.

To probe the influence of hydrogen bonding on the electronic structure of ammonia, gas phase and aqueous NH3 have been investigated using soft X-ray absorption (XAS), resonant inelastic soft X-ray scattering (RIXS), and electronic structure calculations including dynamical effects. Strong spectral differences in the XAS scans as well as in the RIXS spectra between gas phase and aqueous NH3 are attributed to orbital mixing with the water orbitals, dipole-dipole interactions, differences in vibronic coupling, and nuclear dynamics on the time-scale of the RIXS process. All of these effects are consequences of hydrogen bonding and the impact of the associated orbitals, demonstrating the power of XAS and RIXS as unique tools to study hydrogen bonding in liquids.

"Building block picture" of the electronic structure of aqueous cysteine derived from resonant inelastic soft X-ray scattering.

The electronic structure of the amino acid L-cysteine in an aqueous environment was studied using resonant inelastic soft X-ray scattering (RIXS) in a 2D map representation and analyzed in the framework of a "building block" approach. The element selectivity of RIXS allows a local investigation of the electronic structure of the three functional groups of cysteine, namely, the carboxyl, amino, and thiol groups, by measuring at the O K, N K, and S L2,3 edges, respectively. Variation of the pH value allows an investigation of molecules with protonated and deprotonated functional groups, which can then be compared with simple reference molecules that represent the isolated functional groups. We find that such building blocks can provide an excellent description of X-ray emission spectroscopy (XES) and RIXS spectra, but only if all nearest-neighbor atoms are included. This finding is analogous to the building block principle commonly used in X-ray absorption spectroscopy. The building blocks show a distinct spectral character (fingerprint) and allow a comprehensive interpretation of the cysteine spectra. This simple approach opens the path to investigate the electronic structure of more complex biological molecules in aqueous solutions using XES and RIXS.

Setup for in situ investigation of gases and gas/solid interfaces by soft x-ray emission and absorption spectroscopy.

We present a novel gas cell designed to study the electronic structure of gases and gas/solid interfaces using soft x-ray emission and absorption spectroscopies. In this cell, the sample gas is separated from the vacuum of the analysis chamber by a thin window membrane, allowing in situ measurements under atmospheric pressure. The temperature of the gas can be regulated from room temperature up to approximately 600 °C. To avoid beam damage, a constant mass flow can be maintained to continuously refresh the gaseous sample. Furthermore, the gas cell provides space for solid-state samples, allowing to study the gas/solid interface for surface catalytic reactions at elevated temperatures. To demonstrate the capabilities of the cell, we have investigated a TiO2 sample behind a mixture of N2 and He gas at atmospheric pressure.

The Be K-edge in beryllium oxide and chalcogenides: soft x-ray absorption spectra from first-principles theory and experiment.

We have carried out a theoretical and experimental investigation of the beryllium K-edge soft x-ray absorption fine structure of beryllium compounds in the oxygen group, considering BeO, BeS, BeSe, and BeTe. Theoretical spectra are obtained ab initio, through many-body perturbation theory, by solving the Bethe-Salpeter equation (BSE), and by supercell calculations using the core-hole approximation. All calculations are performed with the full-potential linearized augmented plane-wave method. It is found that the two different theoretical approaches produce a similar fine structure, in good agreement with the experimental data. Using the BSE results, we interpret the spectra, distinguishing between bound core-excitons and higher energy excitations.

Non-equivalent carbon atoms in the resonant inelastic soft X-ray scattering map of cysteine.

Resonant inelastic soft x-ray scattering (RIXS) was used to study the electronic structure of solid cysteine films. A RIXS map approach, i.e., plotting the x-ray emission intensity as a function of excitation and emission energy, allows us to separate the contributions of the three chemically non-equivalent carbon atoms in cysteine. In particular, we can identify orbitals localized near the photoexcited atoms, as well as orbitals that are delocalized over the entire molecule.

Ultrafast proton dynamics in aqueous amino acid solutions studied by resonant inelastic soft X-ray scattering.

Resonant inelastic soft X-ray scattering (RIXS) has been used to study the electronic structure of glycine and lysine in aqueous solution. Upon variation of the pH value of the solution from acidic to basic, major changes of the nitrogen K edge RIXS data are observed for both amino acids, which are associated with the protonation and deprotonation of the amino groups. The experimental results are compared with simulations based on density functional theory, yielding a detailed understanding of the spectral changes, as well as insights into the ultrafast proton dynamics in the intermediate core-excited/ionized state of the RIXS process.

Electron-hole correlation effects in core-level spectroscopy probed by the resonant inelastic soft x-ray scattering map of C60.

We have employed a unique spectroscopic approach, a resonant inelastic soft x-ray scattering (RIXS) map, to identify and separate electron-hole correlation effects in core-level spectroscopy. With this approach, we are able to derive a comprehensive picture of the electronic structure, separating ground state properties (such as the HOMO-LUMO separation) from excited state properties (such as the C 1s core-exciton binding energy of C(60)). In particular, our approach allows us to determine the difference between core- and valence exciton binding energies in C(60) [0.5 (±0.2) eV]. Furthermore, the RIXS map gives detailed insight into the symmetries of the intermediate and final states of the RIXS process.

High-resolution, high-transmission soft x-ray spectrometer for the study of biological samples.

We present a variable line-space grating spectrometer for soft x-rays that covers the photon energy range between 130 and 650 eV. The optical design is based on the Hettrick-Underwood principle and tailored to synchrotron-based studies of radiation-sensitive biological samples. The spectrometer is able to record the entire spectral range in one shot, i.e., without any mechanical motion, at a resolving power of 1200 or better. Despite its slitless design, such a resolving power can be achieved for a source spot as large as (30 x 3000) microm2, which is important for keeping beam damage effects in radiation-sensitive samples low. The high spectrometer efficiency allows recording of comprehensive two-dimensional resonant inelastic soft x-ray scattering (RIXS) maps with good statistics within several minutes. This is exemplarily demonstrated for a RIXS map of highly oriented pyrolytic graphite, which was taken within 10 min.

Solid and liquid spectroscopic analysis (SALSA)--a soft x-ray spectroscopy endstation with a novel flow-through liquid cell.

We present a novel synchrotron endstation with a flow-through liquid cell designed to study the electronic structure of liquids using soft x-ray spectroscopies. In this cell, the liquid under study is separated from the vacuum by a thin window membrane, such that the sample liquid can be investigated at ambient pressure. The temperature of the probing volume can be varied in a broad range and with a fast temperature response. The optimized design of the cell significantly reduces the amount of required sample liquid and allows the use of different window membrane types necessary to cover a broad energy range. The liquid cell is integrated into the solid and liquid spectroscopic analysis (SALSA) endstation that includes a high-resolution, high-transmission x-ray spectrometer and a state-of-the-art electron analyzer. The modular design of SALSA also allows the measurement of solid-state samples. The capabilities of the liquid cell and the x-ray spectrometer are demonstrated using a resonant inelastic x-ray scattering map of a 25 wt % NaOD solution.

Isotope and temperature effects in liquid water probed by x-ray absorption and resonant x-ray emission spectroscopy.

High-resolution x-ray absorption and emission spectra of liquid water exhibit a strong isotope effect. Further, the emission spectra show a splitting of the 1b1 emission line, a weak temperature effect, and a pronounced excitation-energy dependence. They can be described as a superposition of two independent contributions. By comparing with gas phase, ice, and NaOH/NaOD, we propose that the two components are governed by the initial state hydrogen bonding configuration and ultrafast dissociation on the time scale of the O 1s core hole decay.

Influence of the preparation conditions on the morphology of perylene thin films on Si(111) and Si(100).

Thin films of perylene on Si(111) and Si(100) substrates have been investigated using a variety of experimental techniques. We find that the structural and morphological properties as well as the growth modes strongly depend on the preparation parameters. In general, we observe the existence of a relatively weak coupling between perylene and the two single crystal substrates. However, under special preparation conditions, it is possible to obtain a multilayer phase on the Si(111) substrate that is characterized by flat-lying, parallel-oriented molecules, and strong coupling with the substrate in the first layer. This phase has different structural, electronic, and intermolecular bonding properties as compared to the known crystalline phases. On Si(100), by varying the deposition rate between 0.1 and 10 nm/min, it is possible to observe a transition from island growth mode, with large and isolated crystallites, to homogeneous film growth. These findings contribute to the basic knowledge for film engineering. Thus, the film morphology could be designed ranging from the growth of very large single grains suitable for a complete nanodevice to homogenous films for application in large displays.

Spectroscopic investigation of the deeply buried Cu(In,Ga)(S,Se)2/Mo interface in thin-film solar cells.

The Cu(In,Ga)(S,Se)(2)Mo interface in thin-film solar cells has been investigated by surface-sensitive photoelectron spectroscopy, bulk-sensitive x-ray emission spectroscopy, and atomic force microscopy. It is possible to access this deeply buried interface by using a suitable lift-off technique, which allows us to investigate the back side of the absorber layer as well as the front side of the Mo back contact. We find a layer of Mo(S,Se)(2) on the surface of the Mo back contact and a copper-poor stoichiometry at the back side of the Cu(In,Ga)(S,Se)(2) absorber. Furthermore, we observe that the Na content at the Cu(In,Ga)(S,Se)(2)Mo interface as well as at the inner grain boundaries in the back contact region is significantly lower than at the absorber front surface.

Structure determination of CdS and ZnS nanoparticles: direct modeling of synchrotron-radiation diffraction data.

We introduce a modified method of powder-diffraction data analysis to obtain precise structural information on freestanding ZnS and CdS nanoparticles with diameters well below 5 nm, i.e., in a range where common bulk-derived approaches fail. The method is based on the Debye equation and allows us to access the crystal structure and the size of the particles with high precision. Detailed information on strain, relaxation effects, stacking faults, and the shape of the particles becomes available. We find significant size differences between our new results and those obtained by established methods, and conclude that a mixed zinc-blende/wurtzite stacking and significant lattice distortions occur in our CdS nanoparticles. Our approach should have direct impact on the understanding and modeling of quantum size effects in nanoparticles.

Bonding and structure of glycine on ordered Al2O3 film surfaces.

The interaction between glycine (NH2CH2COOH) layers and an ultrathin Al2O3 film grown epitaxially onto NiAl(110) was studied by temperature-programmed desorption, X-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, work function measurements, and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. At monolayer coverages at 110 K, there are two coexisting molecular forms: the anionic (NH2CH2COO-) and the zwitterionic form (NH3+CH2COO-) of glycine. As deduced from the photoemission data, the buildup of multilayers at 110 K leads to a condensed phase predominantly in the zwitterionic state. In contrast to the monolayer at 110 K, the monolayer formed at 300 K consists primarily of glycine molecules in the anionic state. The latter species is adsorbed with the oxygen atoms of the carboxylic group pointing toward the substrate. The polarization-dependent C K- and O K-edge NEXAFS spectra indicate that the glycinate species in the monolayer at 300 K is oriented nearly perpendicular to the surface, with the amino group pointing away from the surface.