Ti-15Mo Alloy Decreases the Stress Concentration in Mandibular Angle Fracture Internal Fixation Hardware.

OBJECTIVES: Comparison of the mechanical stability of 2.0 plates made of commercially pure titanium (cpTi) and a titanium-molybdenum (Ti-15Mo) alloy and two methods of internal fixation employed mandibular angle fractures, using 3D finite element analysis. MATERIALS AND METHODS: Four groups were evaluated. For the cpTi: group Eng 1P, one 4-hole plate and 4 screws 6 mm long, in the tension zone of the mandible; group Eng 2P, two 4-hole plates, one in the tension zone of the mandible and the other in the compression zone, both were fixed with 8 screws 6 mm long. The same groups were created for the Ti-15Mo alloy. A 100 N compressive load was applied to the occlusal surface of the mandibular first molar on the plated side. RESULTS: When considering the von Mises equivalent stress (σ vM) values for the comparison between both groups with one plate, a decrease of 10.5% in the plate and a decrease of 29.0% in the screws for the Ti-15Mo group was observed. Comparing the same groups with two plates, a decrease of 28.5% in the screws was shown for the Ti-15Mo alloy group. No significant differences were observed when considering maximum and minimum principal stresses (σ max, σ min), and maximum principal strain (ε max) to the mandibular bone. The Ti-15Mo alloy plates substantially decreased the stress concentration in the screws for both internal fixation techniques and in the plate for the Ti-15Mo 1 plate group. CONCLUSION: From a clinical standpoint, the use of Ti-Mo alloy with reduced stiffness will decrease the stress shielding between the hardware and bone, influencing the outcome of the treatment.

Comparative study of volumetric changes and trabecular microarchitecture in human maxillary sinus bone augmentation with bioactive glass and autogenous bone graft: a prospective and randomized assessment.

The aim of this study was to compare the volumetric changes and the new bone microarchitecture in human maxillary sinuses augmented with bioactive glass (Biogran) alone, bioactive glass combined with autogenous bone graft (1:1), or autogenous bone graft alone. Twelve maxillary sinuses were grafted with bioactive glass (group 1), nine with bioactive glass mixed with autogenous bone graft 1:1 (group 2), and 12 with autogenous bone graft (group 3). Patients underwent cone beam computed tomography 15days after the procedure to determine the initial volume of the graft (T1) and again 6 months later (T2). Biopsies were obtained at the time of dental implant placement and were subjected to micro-computed tomography. The volumetric change was 44.2% in group 1, 37.9% in group 2, and 45.7% in group 3 (P>0.05). The trabecular microarchitecture results showed that the materials used in groups 1 and 2 were good bone substitutes. However, the addition of 50% bioactive glass to autogenous bone graft improved the microarchitecture of the graft. Furthermore, the results for volumetric changes indicated that bioactive glass, its association with autogenous bone graft in a 1:1 ratio, and autogenous bone graft alone have similar resorption.

Three-dimensional strut plate for the treatment of mandibular fractures: a systematic review.

The treatment of mandibular fractures by open reduction and internal fixation is very variable. Thus, there are many controversies about the best fixation system in terms of stability, functional recovery, and postoperative complications. This systematic review sought scientific evidence regarding the best indication for the use of three-dimensional (3D) plates in the treatment of mandibular fractures. A systematic search of the PubMed/MEDLINE, Elsevier/Scopus, and Cochrane Library databases was conducted to include articles published up until November 2016. Following the application of the inclusion criteria, 25 scientific articles were selected for detailed analysis. These studies included a total of 1036 patients (mean age 29 years), with a higher prevalence of males. The anatomical location most involved was the mandibular angle. The success rate of 3D plates was high at this location compared to other methods of fixation. In conclusion, the use of 3D plates for the treatment of mandibular fractures is recommended, since they result in little or no displacement between bone fragments.

Use of autogenous bone and beta-tricalcium phosphate in maxillary sinus lifting: histomorphometric study and immunohistochemical assessment of RUNX2 and VEGF.

The aim of this study was to compare the use of beta-tricalcium phosphate (ß-TCP) (chronOS) with autogenous bone grafts alone in maxillary sinus elevation surgery. The test samples were ß-TCP alone, ß-TCP mixed with autogenous bone grafts (1:1), and autogenous bone grafts alone. Twelve maxillary sinuses were grafted with ß-TCP (group 1), nine with ß-TCP+autogenous bone graft (group 2), and 12 with autogenous bone graft (group 3). After 6 months, biopsies were obtained concurrent to the placement of dental implants; these were subjected to histomorphometric analysis and immunohistochemical analysis for runt-related transcription factor 2 (RUNX2) and vascular endothelial growth factor (VEGF). The average bone formation in group 1 was 46.3±11.6% in the pristine bone region, 47.6±9.9% in the intermediate region, and 44.8±22.1% in the apical region; in group 2, values were 35.0±15.8%, 32.5±13.7%, and 32.8±16.0%, respectively; in group 3, values were 43.1±16.0%, 31.0±13.0%, and 46.1±16.3%, respectively. Immunostaining of samples in group 2 showed high cellular activity and immature bone; this differed from groups 1 and 3, in which mature bone was demonstrated. Thus, this study showed that ß-TCP presents the same behaviour as autogenous bone graft, which makes it a good bone substitute.

Use of autogenous bone and beta-tricalcium phosphate in maxillary sinus lifting: a prospective, randomized, volumetric computed tomography study.

The correction of bone defects can be performed using autogenous or alloplastic materials, such as beta-tricalcium phosphate (ß-TCP). This study compared the changes in bone volume (CBV) after maxillary sinus lifting using autogenous bone (n = 12), autogenous bone associated with ß-TCP 1:1 (ChronOS; DePuy Synthes, Paoli, CA, USA) (n = 9), and ß-TCP alone (n = 11) as grafting material, by means of cone beam computed tomography (CBCT). CBV was evaluated by comparing CBCT scans obtained in the immediate postoperative period (5-7 days) and at 6 months postoperative in each group using OsiriX software (OsiriX Foundation, Geneva, Switzerland). The results showed an average resorption of 45.7 ± 18.6% for the autogenous bone group, 43.8 ± 18.4% for the autogenous bone+ß-TCP group, and 38.3 ± 16.6% for the ß-TCP group. All bone substitute materials tested in this study presented satisfactory results for maxillary sinus lifting procedures regarding the maintenance of graft volume during the healing phase before the insertion of implants, as assessed by means of CBCT.

Avaliação dos acidentes e complicações associados à exodontia dos 3os molares

A exodontia dos terceiros molares é o procedimento mais realizado na especialidade da Cirurgia e Traumatologia Buco-Maxilo-Facial. Neste trabalho foram avaliados os acidentes e complicações ocorridos durante 159 exodontias de terceiros molares realizadas em 83 pacientes. Como resultado, observamos que o trismo foi a principal complicação encontrada 15,66 por cento(13 pacientes), seguida da parestesia do nervo alveolar inferior com trismo 8,43 por cento(7 pacientes). Com relação à posição dentária, os dentes verticais erupcionados apresentaram-se em maior quantidade 27,67 por cento (44 dentes), sendo a técnica III associada à ostectomia e odontossecção utilizada na maioria dos casos 37,73 por cento (60 dentes).(AU)

Fixation of autogenous bone grafts with ethyl-cyanoacrylate glue or titanium screws in the calvaria of rabbits.

This study compared the fixation of autogenous onlay bone grafts with cyanoacrylate glue (Super Bonder) and with titanium screws. Twenty rabbits underwent bilateral parietal ostectomies. Bone segments were fixed anteriorly to the resulting bone defect. In group I, the grafts were fixed with 4 mm long, 1.5 mm diameter screws; in group II, adhesive was used. The animals were killed after 5, 15, 30, 60 and 120 days. Histomorphometric analysis was used to quantify the maintenance of the graft area. Discrete areas of inflammatory reaction were seen in both groups after 5 days and for group II after 15 days. After 30 days, new bone formation was seen at the interface of the grafts. After 120 days, the graft was incorporated into the host bed in group I and partially incorporated in group II. There was a significant statistical difference regarding the mean graft areas between 15 and 120 days (p<0.001) and between fixation methods (p<0.002). Fixation with adhesive promoted a significantly greater area of bone graft than screw fixation, independent of time period. The adhesive was biocompatible, presented similar stability to the screw and maintained the bone area, although there was a delay in graft incorporation.

Rigid internal fixation with titanium versus bioresorbable miniplates in the repair of mandibular fractures in rabbits.

The purpose of this study was to compare by qualitative histology the efficacy of rigid internal fixation with titanium system and the Lacto Sorb system in mandibular fractures in rabbits. Thirty male adult rabbits Oryctolagus cuniculus were used. Unilateral mandibular osteotomies were performed between the canine and first premolar. The animals were divided into two groups: for Group I-rigid internal fixation was performed with titanium system 1.5 mm (Synthes, Oberdorf, Switzerland), with two screws of 6 mm (bicortical) on each side of the osteotomy. For Group II-rigid internal fixation was performed with PLLA/PGA system 1.5 mm (Lacto Sorb, WLorenz, Jacksonville, FL, USA). The histological analysis evaluated the presence of inflammatory reaction, degree of bone healing and degree of resorption of the Lacto Sorb screws. The results of both fixation systems were similar, only with a small difference after 15 and 30 days. In Group I a faster bony healing was noted. But after 60 days, bony healing was similar in both groups. It is concluded that both PLLA/PGA and titanium plates and screws provide sufficient strength to permit mandibular bone healing. The resorption process of PLLA/PGA osteosynthesis material did not cause acute or chronic inflammatory reaction or foreign body reaction during the studied period.

Use of BioGran and Calcitite in bone defects: histologic study in monkeys (Cebus apella).

The present study compares the biologic behavior of BioGran and Calcitite as fillers for surgical cavities in the mandibles of 4 adult monkeys (Cebus apella). The surgical cavities were prepared through both mandibular cortices, with a diameter of 5 mm, in the angle region. Two cavities were prepared on the right side and 1 on the left and divided into 3 groups: R1 sites were filled with bioglass (BioGran), R2 sites were not filled, and L sites were filled with hydroxyapatite (Calcitite). After 180 days the animals were sacrificed and the specimens were removed for histologic processing. Results showed no bone formation in group R2 (empty cavities). BioGran-treated sites showed bone formation and total repair of the bone defect, and the bioglass particles were almost totally resorbed and substituted by bone. The few remaining crystals were in intimate contact with newly formed bone. Calcitite did not allow bone formation, and granules inside the cavities were involved by connective tissue. Based upon those results, the authors concluded that bioglass resulted in total obliteration of the surgical cavity with bone and hydroxyapatite was present in a large amount and involved by connective tissue, without bone formation.