Electrical Doping of Metal Halide Perovskites by Co-Evaporation and Application in PN Junctions.

Electrical doping of semiconductors is a revolutionary development that enabled many electronic and optoelectronic technologies. While doping of many inorganic and organic semiconductors is well-established, controlled electrical doping of metal halide perovskites (MHPs) is yet to be demonstrated. In this work, efficient n- and p-type electrical doping of MHPs by co-evaporating the perovskite precursors alongside organic dopant molecules is achieved. It is demonstrated that the Fermi level can be shifted by up to 500 meV toward the conduction band and by up to 400 meV toward the valence band by n- and p-doping, respectively, which increases the conductivity of the films. The doped layers are employed in PN and NP diodes, showing opposing trends in rectification. Demonstrating controlled electrical doping by a scalable, industrially relevant deposition method opens the route to developing perovskite devices beyond solar cells, such as thermoelectrics or complementary logic.

Influence of chemical interactions on the electronic properties of BiOI/organic semiconductor heterojunctions for application in solution-processed electronics.

Bismuth oxide iodide (BiOI) has been viewed as a suitable environmentally-friendly alternative to lead-halide perovskites for low-cost (opto-)electronic applications such as photodetectors, phototransistors and sensors. To enable its incorporation in these devices in a convenient, scalable, and economical way, BiOI thin films were investigated as part of heterojunctions with various p-type organic semiconductors (OSCs) and tested in a field-effect transistor (FET) configuration. The hybrid heterojunctions, which combine the respective functionalities of BiOI and the OSCs were processed from solution under ambient atmosphere. The characteristics of each of these hybrid systems were correlated with the physical and chemical properties of the respective materials using a concept based on heteropolar chemical interactions at the interface. Systems suitable for application in lateral transport devices were identified and it was demonstrated how materials in the hybrids interact to provide improved and synergistic properties. These indentified heterojunction FETs are a first instance of successful incorporation of solution-processed BiOI thin films in a three-terminal device. They show a significant threshold voltage shift and retained carrier mobility compared to pristine OSC devices and open up possibilities for future optoelectronic applications.

Towards low-temperature processing of efficient γ-CsPbI3 perovskite solar cells.

Inorganic cesium lead iodide (CsPbI3) perovskite solar cells (PSCs) have attracted enormous attention due to their excellent thermal stability and optical bandgap (∼1.73 eV), well-suited for tandem device applications. However, achieving high-performance photovoltaic devices processed at low temperatures is still challenging. Here we reported a new method for the fabrication of high-efficiency and stable γ-CsPbI3 PSCs at lower temperatures than was previously possible by introducing the long-chain organic cation salt ethane-1,2-diammonium iodide (EDAI2) and regulating the content of lead acetate (Pb(OAc)2) in the perovskite precursor solution. We find that EDAI2 acts as an intermediate that can promote the formation of γ-CsPbI3, while excess Pb(OAc)2 can further stabilize the γ-phase of CsPbI3 perovskite. Consequently, improved crystallinity and morphology and reduced carrier recombination are observed in the CsPbI3 films fabricated by the new method. By optimizing the hole transport layer of CsPbI3 inverted architecture solar cells, we demonstrate efficiencies of up to 16.6%, surpassing previous reports examining γ-CsPbI3 in inverted PSCs. Notably, the encapsulated solar cells maintain 97% of their initial efficiency at room temperature and under dim light for 25 days, demonstrating the synergistic effect of EDAI2 and Pb(OAc)2 in stabilizing γ-CsPbI3 PSCs.

Remarkable performance recovery in highly defective perovskite solar cells by photo-oxidation.

Exposure to environmental factors is generally expected to cause degradation in perovskite films and solar cells. Herein, we show that films with certain defect profiles can display the opposite effect, healing upon exposure to oxygen under illumination. We tune the iodine content of methylammonium lead triiodide perovskite from understoichiometric to overstoichiometric and expose them to oxygen and light prior to the addition of the top layers of the device, thereby examining the defect dependence of their photooxidative response in the absence of storage-related chemical processes. The contrast between the photovoltaic properties of the cells with different defects is stark. Understoichiometric samples indeed degrade, demonstrating performance at 33% of their untreated counterparts, while stoichiometric samples maintain their performance levels. Surprisingly, overstoichiometric samples, which show low current density and strong reverse hysteresis when untreated, heal to maximum performance levels (the same as untreated, stoichiometric samples) upon the photooxidative treatment. A similar, albeit smaller-scale, effect is observed for triple cation and methylammonium-free compositions, demonstrating the general application of this treatment to state-of-the-art compositions. We examine the reasons behind this response by a suite of characterization techniques, finding that the performance changes coincide with microstructural decay at the crystal surface, reorientation of the bulk crystal structure for the understoichiometric cells, and a decrease in the iodine-to-lead ratio of all films. These results indicate that defect engineering is a powerful tool to manipulate the stability of perovskite solar cells.

Intermolecular charge transfer enhances the performance of molecular rectifiers.

Molecular-scale diodes made from self-assembled monolayers (SAMs) could complement silicon-based technologies with smaller, cheaper, and more versatile devices. However, advancement of this emerging technology is limited by insufficient electronic performance exhibited by the molecular current rectifiers. We overcome this barrier by exploiting the charge-transfer state that results from co-assembling SAMs of molecules with strong electron donor and acceptor termini. We obtain a substantial enhancement in current rectification, which correlates with the degree of charge transfer, as confirmed by several complementary techniques. These findings provide a previously enexplored method for manipulating the properties of molecular electronic devices by exploiting donor/acceptor interactions. They also serve as a model test platform for the study of doping mechanisms in organic systems. Our devices have the potential for fast widespread adoption due to their low-cost processing and self-assembly onto silicon substrates, which could allow seamless integration with current technologies.

Traps and transport resistance are the next frontiers for stable non-fullerene acceptor solar cells.

Stability is one of the most important challenges facing material research for organic solar cells (OSC) on their path to further commercialization. In the high-performance material system PM6:Y6 studied here, we investigate degradation mechanisms of inverted photovoltaic devices. We have identified two distinct degradation pathways: one requires the presence of both illumination and oxygen and features a short-circuit current reduction, the other one is induced thermally and marked by severe losses of open-circuit voltage and fill factor. We focus our investigation on the thermally accelerated degradation. Our findings show that bulk material properties and interfaces remain remarkably stable, however, aging-induced defect state formation in the active layer remains the primary cause of thermal degradation. The increased trap density leads to higher non-radiative recombination, which limits the open-circuit voltage and lowers the charge carrier mobility in the photoactive layer. Furthermore, we find the trap-induced transport resistance to be the major reason for the drop in fill factor. Our results suggest that device lifetimes could be significantly increased by marginally suppressing trap formation, leading to a bright future for OSC.

Oxygen-induced degradation in AgBiS2 nanocrystal solar cells.

AgBiS2 nanocrystal solar cells are among the most sustainable emerging photovoltaic technologies. Their environmentally-friendly composition and low energy consumption during fabrication make them particularly attractive for future applications. However, much remains unknown about the stability of these devices, in particular under operational conditions. In this study, we explore the effects of oxygen and light on the stability of AgBiS2 nanocrystal solar cells and identify its dependence on the charge extraction layers. Normally, the rate of oxygen-induced degradation of nanocrystals is related to their ligands, which determine the access sites by steric hindrance. We demonstrate that the ligands, commonly used in AgBiS2 solar cells, also play a crucial chemical role in the oxidation process. Specifically, we show that the tetramethylammonium iodide ligands enable their oxidation, leading to the formation of bismuth oxide and silver sulphide. Additionally, the rate of oxidation is impacted by the presence of water, often present at the surface of the ZnO electron extraction layer. Moreover, the degradation of the organic hole extraction layer also impacts the overall device stability and the materials' photophysics. The understanding of these degradation processes is necessary for the development of mitigation strategies for future generations of more stable AgBiS2 nanocrystal solar cells.

23.7% Efficient inverted perovskite solar cells by dual interfacial modification.

Despite remarkable progress, the performance of lead halide perovskite solar cells fabricated in an inverted structure lags behind that of standard architecture devices. Here, we report on a dual interfacial modification approach based on the incorporation of large organic cations at both the bottom and top interfaces of the perovskite active layer. Together, this leads to a simultaneous improvement in both the open-circuit voltage and fill factor of the devices, reaching maximum values of 1.184 V and 85%, respectively, resulting in a champion device efficiency of 23.7%. This dual interfacial modification is fully compatible with a bulk modification of the perovskite active layer by ionic liquids, leading to both efficient and stable inverted architecture devices.

The Role of Additives in Suppressing the Degradation of Liquid-Exfoliated WS2 Monolayers.

Group VI transition metal dichalcogenides (TMDs) are considered to be chemically widely inert, but recent reports point toward an oxidation of monolayered sheets in ambient conditions, due to defects. To date, the degradation of monolayered TMDs is only studied on individual, substrate-supported nanosheets with varying defect type and concentration, strain, and in an inhomogeneous environment. Here, degradation kinetics of WS2 nanosheet ensembles in the liquid phase are investigated through photoluminescence measurements, which selectively probe the monolayers. Monolayer-enriched WS2 dispersions are produced with varying lateral sizes in the two common surfactant stabilizers sodium cholate (SC) and sodium dodecyl sulfate (SDS). Well-defined degradation kinetics are observed, which enable the determination of activation energies of the degradation and decouple photoinduced and thermal degradation. The thermal degradation is slower than the photoinduced degradation and requires higher activation energy. Using SC as surfactant, it is sufficiently suppressed. The photoinduced degradation can be widely prevented through chemical passivation achieved through the addition of cysteine which, on the one hand, coordinates to defects on the nanosheets and, on the other hand, stabilizes oxides on the surface, which shield the nanosheets from further degradation.

Doped Organic Hole Extraction Layers in Efficient PbS and AgBiS2 Quantum Dot Solar Cells.

The efficiency of PbS quantum dot (QD) solar cells has significantly increased in recent years, strengthening their potential for industrial applications. The vast majority of state-of-the-art devices utilize 1,2-ethanedithiol (EDT)-coated PbS QD hole extraction layers, which lead to high initial performance, but result in poor device stability. While excellent performance has also been demonstrated with organic extraction layers, these devices include a molybdenum trioxide (MoO3) layer, which is also known to decrease device stability. Herein, we demonstrate that organic layers based on a poly[bis(4-phenyl)(2,4,6-trimethylphenyl)amine] (PTAA) polymer doped with C60F48 can serve as hole extraction layers for efficient EDT-free and MoO3-free QD solar cells. Such layers are shown to offer high conductivity for facile hole transport to the anode, while effectively blocking electrons due to their low electron affinity. We show that our approach is versatile and is applicable also to AgBiS2 QD solar cells.

Sustainability in Perovskite Solar Cells.

At a current value of 25.5%, perovskites have reached some of the highest power conversion efficiencies of all single-junction solar cell devices. Researchers, however, are questioning their readiness for the commercial market, citing reasons of the toxicity of the lead-based active layer and instability. Closer examination of the life cycle of perovskite solar cells reveals that there are more areas than just these which should be addressed in order to bring an environmentally friendly and sustainable technology to global use. In this review, we discuss these issues. Life cycle analyses show that high temperature processes, heavy use of organic solvents, and extensive use of certain materials can have high up and downstream consequences in terms of emissions, human and ecotoxicity. We further bring attention to the toxicity of the perovskites themselves, where the most direct analyses suggest that the lead cannot be considered totally safe, despite its small quantity and that replacements such as tin may be more toxic in certain scenarios. As a way to reduce the negative environmental impact, we highlight ways in which researchers have used encapsulation and recycling to extend the life of the entire unit and its components and to prevent lead leakage. We hope this review directs researchers toward new strategies to introduce a clean solar technology to the world.

Vacuum-Induced Degradation of 2D Perovskites.

Two-dimensional (2D) hybrid organic-inorganic perovskites have recently attracted the attention of the scientific community due to their exciting optical and electronic properties as well as enhanced stability upon exposure to environmental factors. In this work, we investigate 2D perovskite layers with a range of organic cations and report on the Achilles heel of these materials-their significant degradation upon exposure to vacuum. We demonstrate that vacuum exposure induces the formation of a metallic lead species, accompanied by a loss of the organic cation from the perovskite. We investigate the dynamics of this reaction, as well as the influence of other factors, such as X-ray irradiation. Furthermore, we characterize the effect of degradation on the microstructure of the 2D layers. Our study highlights that despite earlier reports, 2D perovskites may exhibit instabilities, the chemistry of which should be identified and investigated in order to develop suitable mitigation strategies.

Enhancing the Open-Circuit Voltage of Perovskite Solar Cells by Embedding Molecular Dipoles within Their Hole-Blocking Layer.

Engineering the energetics of perovskite photovoltaic devices through deliberate introduction of dipoles to control the built-in potential of the devices offers an opportunity to enhance their performance without the need to modify the active layer itself. In this work, we demonstrate how the incorporation of molecular dipoles into the bathocuproine (BCP) hole-blocking layer of inverted perovskite solar cells improves the device open-circuit voltage (VOC) and, consequently, their performance. We explore a series of four thiaazulenic derivatives that exhibit increasing dipole moments and demonstrate that these molecules can be introduced into the solution-processed BCP layer to effectively increase the built-in potential within the device without altering any of the other device layers. As a result, the VOC of the devices is enhanced by up to 130 mV, with larger dipoles resulting in higher VOC. To investigate the limitations of this approach, we employ numerical device simulations that demonstrate that the highest dipole derivatives used in this work eliminate all limitations on the VOC stemming from the built-in potential of the device.

Fluorination of Organic Spacer Impacts on the Structural and Optical Response of 2D Perovskites.

Low-dimensional hybrid perovskites have triggered significant research interest due to their intrinsically tunable optoelectronic properties and technologically relevant material stability. In particular, the role of the organic spacer on the inherent structural and optical features in two-dimensional (2D) perovskites is paramount for material optimization. To obtain a deeper understanding of the relationship between spacers and the corresponding 2D perovskite film properties, we explore the influence of the partial substitution of hydrogen atoms by fluorine in an alkylammonium organic cation, resulting in (Lc)2PbI4 and (Lf)2PbI4 2D perovskites, respectively. Consequently, optical analysis reveals a clear 0.2 eV blue-shift in the excitonic position at room temperature. This result can be mainly attributed to a band gap opening, with negligible effects on the exciton binding energy. According to Density Functional Theory (DFT) calculations, the band gap increases due to a larger distortion of the structure that decreases the atomic overlap of the wavefunctions and correspondingly bandwidth of the valence and conduction bands. In addition, fluorination impacts the structural rigidity of the 2D perovskite, resulting in a stable structure at room temperature and the absence of phase transitions at a low temperature, in contrast to the widely reported polymorphism in some non-fluorinated materials that exhibit such a phase transition. This indicates that a small perturbation in the material structure can strongly influence the overall structural stability and related phase transition of 2D perovskites, making them more robust to any phase change. This work provides key information on how the fluorine content in organic spacer influence the structural distortion of 2D perovskites and their optical properties which possess remarkable importance for future optoelectronic applications, for instance in the field of light-emitting devices or sensors.

Efficient n-Doping and Hole Blocking in Single-Walled Carbon Nanotube Transistors with 1,2,4,5-Tetrakis(tetramethylguanidino)ben-zene.

Efficient, stable, and solution-based n-doping of semiconducting single-walled carbon nanotubes (SWCNTs) is highly desired for complementary circuits but remains a significant challenge. Here, we present 1,2,4,5-tetrakis(tetramethylguanidino)benzene (ttmgb) as a strong two-electron donor that enables the fabrication of purely n-type SWCNT field-effect transistors (FETs). We apply ttmgb to networks of monochiral, semiconducting (6,5) SWCNTs that show intrinsic ambipolar behavior in bottom-contact/top-gate FETs and obtain unipolar n-type transport with 3-5-fold enhancement of electron mobilities (approximately 10 cm2 V-1 s-1), while completely suppressing hole currents, even at high drain voltages. These n-type FETs show excellent on/off current ratios of up to 108, steep subthreshold swings (80-100 mV/dec), and almost no hysteresis. Their excellent device characteristics stem from the reduction of the work function of the gold electrodes via contact doping, blocking of hole injection by ttmgb2+ on the electrode surface, and removal of residual water from the SWCNT network by ttmgb protonation. The ttmgb-treated SWCNT FETs also display excellent environmental stability under bias stress in ambient conditions. Complementary inverters based on n- and p-doped SWCNT FETs exhibit rail-to-rail operation with high gain and low power dissipation. The simple and stable ttmgb molecule thus serves as an example for the larger class of guanidino-functionalized aromatic compounds as promising electron donors for high-performance thin film electronics.

Effect of Injection Layer Sub-Bandgap States on Electron Injection in Organic Light-Emitting Diodes.

It is generally considered that the injection of charges into an active layer of an organic light-emitting diode (OLED) is solely determined by the energetic injection barrier formed at the device interfaces. Here, we demonstrate that the density of surface states of the electron-injecting ZnO layer has a profound effect on both the charge injection and the overall performance of the OLED device. Introducing a dopant into ZnO reduces both the energy depth and density of surface states without altering the position of the energy levels-thus, the magnitude of the injection barrier formed at the organic/ZnO interface remains unchanged. Changes observed in the density of surface states result in an improved electron injection and enhanced luminescence of the device. We implemented a numerical simulation, modeling the effects of energetics and the density of surface states on the electron injection, demonstrating that both contributions should be considered when choosing the appropriate injection layer.