Biochar as a low-cost, eco-friendly, and electrically conductive material for terahertz applications.

We investigate conducting characteristics of biochar derived from the pyrolysis of a paper at terahertz frequencies. Paper is annealed under temperatures ranging from 600 to 1000 °C to modify structural and electrical properties. We experimentally observe that the terahertz conductivity increases above 102 S/m as the annealing temperature increases up to 800 °C. From structural characterization using energy-dispersive X-ray spectroscopy, Fourier-transform infrared spectroscopy, Raman spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy, we confirm that more graphitic biochars are produced in high annealing temperature, in agreement with the improvement of terahertz conductivity. Our results show that biochar can be a highly promising candidate to be used in paper-based devices operating at terahertz frequencies.

Detection of Microplastic in Salts Using Terahertz Time-Domain Spectroscopy.

We report on a prototypical study of the detection of microplastic embedded in table salts by using terahertz time-domain spectroscopy. In the experiment, high-density polyethylene (HDPE) of sizes from 150 to 400 µm are used as a representative microplastic and mixed with table salts. Analyzing terahertz transmittance with an effective medium model, we extract various optical properties such as refractive index, absorption coefficient, and real/imaginary parts of the dielectric constant of the mixture. Consequently, the optical properties exhibit volume-ratio-dependence in 0.1-0.5 THz regimes. Especially, the refractive index and the real part of the dielectric constant possess monotonic frequency dependence, meaning that the quantities can be relevant indicators for the detection of the microplastic in terms of practical applications. Our work proves that terahertz time-domain spectroscopy can pave a way to recognize microplastic mixed with salts and be expanded for detecting various micro-sized particles.

Copper-based etalon filter using antioxidant graphene layer.

Copper is a low-cost material compared to silver and gold, having high reflectivity in the near infrared spectral range as well as good electrical and thermal conductivity. Its properties make it a good candidate for metal-based low-cost multilayer thin-film devices and optical components. However, its high reflectance in the devices is reduced because copper is easily oxidized. Here, we suggest a copper-based Fabry-Perot optical filter consisting of a thin dielectric layer stacked between two copper films, which can realize low-cost production compared to a conventional silver-based etalon filter. The reduced performance due to the inherent oxidation of the copper surface can be overcome by passivating the copper films with monolayer graphene. The anti-oxidation of copper film is investigated by optical microscopy, x-ray photoelectron spectroscopy, and transmission measurement in UV-vi spectral ranges. Our results show that the graphene coating can be expanded for various metal-based optical devices in terms of anti-corrosion.

Author Correction: Apparent Power Law Scaling of Variable Range Hopping Conduction in Carbonized Polymer Nanofibers.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Anomalous Negative Resistance Phenomena in Twisted Superconducting Nanowire Yarns.

We report unusual absolute negative resistance phenomena in twisted superconducting yarns consisting of niobium-nitride (NbN) nanowires formed on a template of aligned carbon nanotube (CNT) sheets. In the vicinity of the superconducting critical temperature and critical current, the electrical resistance with a standard four-probe configuration exhibits negative values for many wire-shaped twisted yarns. This anomalous behavior at the superconducting transition stage is analyzed using a simplified circuit model, where the charge conduction is determined by the combination between the intra- and internanofiber transports inside the yarn. The superconducting transition of intrafibrillar transport along CNT-templated NbN nanowires was distinguished from that of an interfibrillar one, where the latter exhibits the ensemble property of superconducting weak links among adjacent NbN nanowires. Furthermore, the topological similarity between the sheet of an aligned array of nanowires and the yarn of twisted nanofibrils enables the occurrence of this anomaly. This study indicates that the quantitative network-based approach is effective for the analysis of anomalous charge conduction through nanowire-based anisotropic materials.

Author Correction: Graphene-assisted biosensing based on terahertz nanoslot antennas.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

Graphene-assisted biosensing based on terahertz nanoslot antennas.

We report on improvement of sensitivity for molecular detection utilizing terahertz time domain spectroscopy. Based on confining and enhancing electromagnetic field with metallic nanoslot antennas, we additionally employ monolayer graphene sheet whose edge and hydrophobic surface nature lead to increase detecting performance. Terahertz transmittance in monolayer graphene/metallic nanoslot structure exhibits more unambiguous change after lactose molecules are attached, compared to that in metallic nanoslot structure without monolayer graphene. We attribute the prominent change to that more lactose molecules are guided inside/near the metal gap region due to edge and hydrophobic surface nature of monolayer graphene. This monolayer graphene/metallic nanoslot structure can be expanded in other organic or bio-molecular detection.

Tuning the electronic structure of single-walled carbon nanotube by high-pressure H2 exposure.

We report on an electronic structure change of single-walled carbon nanotube (SWNT) on hexagonal boron nitride due to electron doping via high-pressure H2 exposure. The fractional coverage of hydrogenated carbon atom is estimated to be at least θ = 0.163 from the in situ I ds-V g measurements of the release process. Raman spectroscopy and x-ray photoelectron spectroscopy were carried out to support the in situ electrical measurements. In particular, we used the dissociative Langmuir-type model to yield the desorption coefficient k des by fitting it to the in situ electrical data. Finally, we applied this hydrogenation method to the SWNT network on the commercial Si/SiO2 substrate to open the possibility of the scalable n-type semiconducting SWNT FETs.

Probing variable range hopping lengths by magneto conductance in carbonized polymer nanofibers.

Using magneto transport, we probe hopping length scales in the variable range hopping conduction of carbonized polyacetylene and polyaniline nanofibers. In contrast to pristine polyacetylene nanofibers that show vanishing magneto conductance at large electric fields, carbonized polymer nanofibers display a negative magneto conductance that decreases in magnitude but remains finite with respect to the electric field. We show that this behavior of magneto conductance is an indicator of the electric field and temperature dependence of hopping length in the gradual transition from the thermally activated to the activation-less electric field driven variable range hopping transport. This reveals magneto transport as a useful tool to probe hopping lengths in the non-linear hopping regime.

Personal pronoun usage in maternal input to infants at high vs. low risk for autism spectrum disorder.

Children with autism spectrum disorder (ASD) are prone to personal pronoun difficulties. This paper investigates maternal input as a potential contributing factor, focusing on an early developmental stage before ASD diagnosis. Using Quigley and McNally's (2013) corpus of maternal speech to infants (3-19 months; N = 19) who are either at high or low risk for a diagnosis of ASD (Quigley & McNally, 2013), we asked whether mothers used fewer pronouns with high-risk infants. Indeed, high-risk infants heard fewer second-person pronouns relative to their names than low-risk infants. We further investigated the contexts in which mothers were using infants' names. Our results indicated that mothers of high-risk infants often used the infants' names simply to get their attention by calling them. We suggest that high-risk infants may thus hear relatively fewer pronouns because their mothers spend more time trying to get their attention. This may be related to differences in social-communicative behavior between low-risk and high-risk infants.

Apparent Power Law Scaling of Variable Range Hopping Conduction in Carbonized Polymer Nanofibers.

We induce dramatic changes in the structure of conducting polymer nanofibers by carbonization at 800 °C and compare charge transport properties between carbonized and pristine nanofibers. Despite the profound structural differences, both types of systems display power law dependence of current with voltage and temperature, and all measurements can be scaled into a single universal curve. We analyze our experimental data in the framework of variable range hopping and argue that this mechanism can explain transport properties of pristine polymer nanofibers as well.

Citrus-Peel-Derived, Nanoporous Carbon Nanosheets Containing Redox-Active Heteroatoms for Sodium-Ion Storage.

Advanced design of nanostructured functional carbon materials for use in sustainable energy storage systems suffers from complex fabrication procedures and the use of special methods and/or expensive precursors, limiting their practical applications. In this study, nanoporous carbon nanosheets (NP-CNSs) containing numerous redox-active heteroatoms (C/O and C/N ratios of 5.5 and 34.3, respectively) were fabricated from citrus peels by simply heating the peels in the presence of potassium ions. The NP-CNSs had a 2D-like morphology with a high aspect ratio of >100, high specific surface area of 1167 m(2) g(-1), and a large amount of nanopores between 1 and 5 nm. The NP-CNSs also had an electrical conductivity of 2.6 × 10(1) s cm(-1), which is approximately 50 times higher than that of reduced graphene oxide. These unique material properties resulted in superior electrochemical performance with a high specific capacity of 140 mAh g(-1) in the cathodic potential range. In addition, symmetric full-cell devices based on the NP-CNSs showed excellent cyclic performance over 100,000 repetitive cycles.

Sodium-Ion Storage in Pyroprotein-Based Carbon Nanoplates.

Pyroprotein-based carbon nanoplates are fabricated from self-assembled silk proteins as a versatile platform to examine sodium-ion storage characteristics in various carbon environments. It is found that, depending on the local carbon structure, sodium ions are stored via chemi-/physisorption, insertion, or nanoclustering of metallic sodium.

Electronic transport of recrystallized freestanding graphene nanoribbons.

The use of graphene and other two-dimensional materials in next-generation electronics is hampered by the significant damage caused by conventional lithographic processing techniques employed in device fabrication. To reduce the density of defects and increase mobility, Joule heating is often used since it facilitates lattice reconstruction and promotes self-repair. Despite its importance, an atomistic understanding of the structural and electronic enhancements in graphene devices enabled by current annealing is still lacking. To provide a deeper understanding of these mechanisms, atomic recrystallization and electronic transport in graphene nanoribbon (GNR) devices are investigated using a combination of experimental and theoretical methods. GNR devices with widths below 10 nm are defined and electrically measured in situ within the sample chamber of an aberration-corrected transmission electron microscope. Immediately after patterning, we observe few-layer polycrystalline GNRs with irregular sp(2)-bonded edges. Continued structural recrystallization toward a sharp, faceted edge is promoted by increasing application of Joule heat. Monte Carlo-based annealing simulations reveal that this is a result of concentrated local currents at lattice defects, which in turn promotes restructuring of unfavorable edge structures toward an atomically sharp state. We establish that intrinsic conductance doubles to 2.7 e(2)/h during the recrystallization process following an almost 3-fold reduction in device width, which is attributed to improved device crystallinity. In addition to the observation of consistent edge bonding in patterned GNRs, we further motivate the use of bonded bilayer GNRs for future nanoelectronic components by demonstrating how electronic structure can be tailored by an appropriate modification of the relative twist angle of the bonded bilayer.

Hierarchically porous carbon nanosheets from waste coffee grounds for supercapacitors.

The nanostructure design of porous carbon-based electrode materials is key to improving the electrochemical performance of supercapacitors. In this study, hierarchically porous carbon nanosheets (HP-CNSs) were fabricated using waste coffee grounds by in situ carbonization and activation processes using KOH. Despite the simple synthesis process, the HP-CNSs had a high aspect ratio nanostructure (∼20 nm thickness to several micrometers in lateral size), a high specific surface area of 1945.7 m(2) g(-1), numerous heteroatoms, and good electrical transport properties, as well as hierarchically porous characteristics (0.5-10 nm in size). HP-CNS-based supercapacitors showed a specific energy of 35.4 Wh kg(-1) at 11250 W kg(-1) and of 23 Wh kg(-1) for a 3 s charge/discharge current rate corresponding to a specific power of 30000 W kg(-1). Additionally, the HP-CNS supercapacitors demonstrated good cyclic performance over 5000 cycles.

Electronic transport in heterostructures of chemical vapor deposited graphene and hexagonal boron nitride.

CVD graphene devices on stacked CVD hexagonal boron nitride (hBN) are demonstrated using a novel low-contamination transfer method, and their electrical performance is systematically compared to devices on SiO(2). An order of magnitude improvement in mobility, sheet resistivity, current density, and sustained power is reported when the oxide substrate is covered with five-layer CVD hBN.

Correlating atomic structure and transport in suspended graphene nanoribbons.

Graphene nanoribbons (GNRs) are promising candidates for next generation integrated circuit (IC) components; this fact motivates exploration of the relationship between crystallographic structure and transport of graphene patterned at IC-relevant length scales (<10 nm). We report on the controlled fabrication of pristine, freestanding GNRs with widths as small as 0.7 nm, paired with simultaneous lattice-resolution imaging and electrical transport characterization, all conducted within an aberration-corrected transmission electron microscope. Few-layer GNRs very frequently formed bonded-bilayers and were remarkably robust, sustaining currents in excess of 1.5 µA per carbon bond across a 5 atom-wide ribbon. We found that the intrinsic conductance of a sub-10 nm bonded bilayer GNR scaled with width as GBL(w) ≈ 3/4(e(2)/h)w, where w is the width in nanometers, while a monolayer GNR was roughly five times less conductive. Nanosculpted, crystalline monolayer GNRs exhibited armchair-terminated edges after current annealing, presenting a pathway for the controlled fabrication of semiconducting GNRs with known edge geometry. Finally, we report on simulations of quantum transport in GNRs that are in qualitative agreement with the observations.

Scalable production of highly sensitive nanosensors based on graphene functionalized with a designed G protein-coupled receptor.

We have developed a novel, all-electronic biosensor for opioids that consists of an engineered µ-opioid receptor protein, with high binding affinity for opioids, chemically bonded to a graphene field-effect transistor to read out ligand binding. A variant of the receptor protein that provided chemical recognition was computationally redesigned to enhance its solubility and stability in an aqueous environment. A shadow mask process was developed to fabricate arrays of hundreds of graphene transistors with average mobility of ∼1500 cm(2) V(-1) s(-1) and yield exceeding 98%. The biosensor exhibits high sensitivity and selectivity for the target naltrexone, an opioid receptor antagonist, with a detection limit of 10 pg/mL.

N-type graphene induced by dissociative H2 adsorption at room temperature.

Studies of the interaction between hydrogen and graphene have been increasingly required due to the indispensable modulation of the electronic structure of graphene for device applications and the possibility of using graphene as a hydrogen storage material. Here, we report on the behaviour of molecular hydrogen on graphene using the gate voltage-dependent resistance of single-, bi-, and multi-layer graphene sheets as a function of H2 gas pressure up to 24 bar from 300 K to 345 K. Upon H2 exposure, the charge neutrality point shifts toward the negative gate voltage region, indicating n-type doping, and distinct Raman signature changes, increases in the interlayer distance of multi-layer graphene, and a decrease in the d-spacing occur, as determined by TEM. These results demonstrate the occurrence of dissociative H2 adsorption due to the existence of vacancy defects on graphene.

Enhancing the viability of fat grafts using new transfer medium containing insulin and beta-fibroblast growth factor in autologous fat transplantation.

With the increasing application of liposuction in reconstructive surgery of the head and neck region and aesthetic plastic surgery of the facial region, autologous fat transplantation is widely used. However, due to the high absorption rate of fat grafts, a number of studies have examined the use of different agents to increase the viability of such grafts. Here, we evaluated the effects of a new transfer medium containing insulin and beta-fibroblast growth factor, which can increase the viability of fat grafts before performing autologous fat transplantation. Twenty-four New Zealand white rabbits were used in this study. For each rabbit, we harvested 4mg of fat from both inguinal regions. The samples from each rabbit were pooled, divided into four equal aliquots and then soaked in a transfer medium. Group I was the control group with normal saline as the transfer medium, group II used modified Dulbecco's modified Eagle's medium (modified DMEM), group III used modified DMEM with insulin and group IV used modified DMEM with insulin and beta-fibroblast growth factor. After dividing the dorsum of each rabbit into four even parts, one fat sample from each group was transplanted into one of the pockets created in the loose areolar tissue immediately beneath the dermis. Six rabbits were euthanised using pentobarbital sodium each time, 1, 3, 6 and 12 months after fat transplantation, and we measured the weights of the fat grafts and examined the histological changes using light microscopy. Groups III and IV showed significantly greater viability of fat grafts than the controls in the group I. On histological examination, large numbers of mature adipocytes were observed in groups III and IV, and reduced cyst formation and fibrosis were also observed. Autologous fat transplantation using the new transfer medium containing insulin and beta-fibroblast growth factor is a simple, promising strategy for clinical application designed to augment the viability of fat transplantation.