LIPSS-based functional surfaces produced by multi-beam nanostructuring with 2601 beams and real-time thermal processes measurement.

A unique combination of the ultrashort high-energy pulsed laser system with exceptional beam quality and a novel Diffractive Optical Element (DOE) enables simultaneous production of 2601 spots organized in the square-shaped 1 × 1 mm matrix in less than 0.01 ms. By adjusting the laser and processing parameters each spot can contain Laser Induced Periodic Surface Structures (LIPSS, ripples), including high-spatial frequency LIPSS (HFSL) and low-spatial frequency LIPSS (LSFL). DOE placed before galvanometric scanner allows easy integration and stitching of the pattern over larger areas. In addition, the LIPSS formation was monitored for the first time using fast infrared radiometry for verification of real-time quality control possibilities. During the LIPSS fabrication, solidification plateaus were observed after each laser pulse, which enables process control by monitoring heat accumulation or plateau length using a new signal derivation approach. Analysis of solidification plateaus after each laser pulse enabled dynamic calibration of the measurement. Heat accumulation temperatures from 200 to 1000 °C were observed from measurement and compared to the theoretical model. The temperature measurements revealed interesting changes in the physics of the laser ablation process. Moreover, the highest throughput on the area of 40 × 40 mm reached 1910 cm2/min, which is the highest demonstrated throughput of LIPSS nanostructuring, to the best of our knowledge. Thus, showing great potential for the efficient production of LIPSS-based functional surfaces which can be used to improve surface mechanical, biological or optical properties.

Analysis of short wavelength infrared radiation during laser welding of plastics.

In this paper, a new measurement system and a new approach in calculation for infrared (IR) radiation investigation in quasi-simultaneous transmission laser welding of plastics are presented. The measurement system is based on a MW/SWIR (medium-wave/short-wave IR) camera and optical filters narrowing the spectral region to SWIR. The measured signals contain radiation from the melted zone in between the semitransparent and absorbing polymers, as well as radiation from the surface and interior of the semitransparent polymer. The new calculation approach was developed to distinguish between these signals. It is based on simplification of the process to two places with two temperatures (surface and molten interface) and knowledge of the spectral optical properties of the material, filters, and camera response. The results of measurement and calculation for three different optical filters and polyoxymethylene samples with two thicknesses are shown and discussed. Good agreement is obtained for the calculation variant using normal transmissivity of the semitransparent polymer.

Survey of emissivity measurement by radiometric methods.

A survey of the state of the art in the field of spectral directional emissivity measurements by using radiometric methods is presented. Individual quantity types such as spectral, band, or total emissivity are defined. Principles of emissivity measurement by various methods (direct and indirect, and calorimetric and radiometric) are discussed. The paper is focused on direct radiometric methods. An overview of experimental setups is provided, including the design of individual parts such as the applied reference sources of radiation, systems of sample clamping and heating, detection systems, methods for the determination of surface temperature, and procedures for emissivity evaluation.

Fluticasone propionate 750 micrograms/day versus beclomethasone dipropionate 1500 micrograms/day: comparison of efficacy and adrenal function in paediatric asthma.

BACKGROUND: Previous studies have suggested a 2:1 efficacy advantage of fluticasone propionate (FP) over beclomethasone dipropionate (BDP) in adults on high dose inhaled steroids and children on low dose inhaled steroids. The lower doses of FP required to provide equivalent efficacy to BDP also appear to have fewer systemic effects as measured by adrenal function. METHODS: The efficacy and safety of FP 750 micrograms/day and BDP 1500 micrograms/day were compared in 30 children with persistent asthma (requiring 1000-2000 micrograms/day of inhaled corticosteroids) in a 12 week randomised double blind crossover study. Medication was delivered by a spacer device in two divided doses. Primary efficacy variables were peak expiratory flows (PEF). Adrenal function was assessed by 24 hour urinary free cortisol levels at eight and 12 weeks and ACTH and low dose synacthen tests (LDST) at 12 weeks. The results were adjusted for sequence and period differences. RESULTS: There was no difference in the primary efficacy variables over the two 12 week treatment periods (difference in adjusted means for morning PEF 1.3 l/min (95% CI -6.1 to 8.8), p = 0.112) and symptom scores (cough, tachypnoea, wheeze, shortness of breath; difference in adjusted means of night time scores: -0.06 (95% CI -0.14 to 0.03); p = 0.136). Similar degrees of mild adrenal dysfunction were found during BDP and FP treatment phases. Identical height gain velocities were shown during the corresponding periods. CONCLUSIONS: FP 750 micrograms/day is as effective as BDP 1500 micrograms/day in children with persistent asthma. At these very high doses we were unable to demonstrate a safety advantage of FP over BDP as assessed by adrenal function. However, measures of adrenal function may have been influenced by concurrent and previous systemic steroid usage, and possibly by effects of disease activity.