RESUMO
As one of the most important modes of transportation, the safety of running trains and railway tracks is significant. It is essential to power sensors that detect and track health in remote areas. The vibration energy of the track structure is enormous, stable, and not limited by weather factors such as the sun and wind. A new type of arch beam piezoelectric stack energy harvester for railway systems is studied in this paper. Through simulation analyses and experimental verification of the energy harvester, the influences of external resistance, load, pre-stress, and load frequency on the energy harvesting performance of the piezoelectric energy harvester are discussed. When the frequency is less than 6 Hz, the energy capture efficiency is greatly affected by the frequency. When the frequency exceeds 6 Hz, the frequency has little effect and the load dramatically affects the energy capture efficiency. The pre-stress has little effect on the energy capture efficiency, but there is an optimal value at 4.5 kN. The energy harvester has an output power of 193 mW, a weight of 912 g, and the energy density can reach 211.8 µW/g. These results can provide a reference for subsequent experiments in the actual environment.
RESUMO
This work presents a novel bird-shaped broadband piezoelectric energy harvester based on a two-DOF crossed beam for low-frequency environmental vibrations. The harvester features a cantilever mounted on a double-hinged beam, whose rotating motions effectively diminish its natural frequencies. Numerical simulation based on the finite element method is conducted to analyze the modal shapes and the harmonic response of the proposed harvester. Prototypes are fabricated and experiments are carried out by a testing system, whose results indicate a good agreement with the simulation. The multi-frequency energy harvesting is achieved at the first-, second-, and fifth-order resonances. In particular, the proposed harvester demonstrates the remarkable output characteristics of 9.53 mW and 1.83 mW at frequencies as low as 19.23 HZ and 45.38 Hz, which are superior to the majority of existing energy harvesters. Besides, the influences of key parameters on the harvesting performance are experimentally investigated to optimize the environmental adaptability of the harvester. This work provides a new perspective for efficiently harvesting the low-frequency vibration energy, which can be utilized for supplying power to electronic devices.
RESUMO
This paper studies a novel enhanced energy-harvesting method to harvest water flow-induced vibration with a tandem arrangement of two piezoelectric energy harvesters (PEHs) in the direction of flowing water, through simulation modeling and experimental validation. A mathematical model is established by two individual-equivalent single-degree-of-freedom models, coupled with the hydrodynamic force obtained by computational fluid dynamics. Through the simulation analysis, the variation rules of vibration frequency, vibration amplitude, power generation and the distribution of flow field are obtained. And experimental tests are performed to verify the numerical calculation. The experimental and simulation results show that the upstream piezoelectric energy harvester (UPEH) is excited by the vortex-induced vibration, and the maximum value of performance is achieved when the UPEH and the vibration are resonant. As the vortex falls off from the UPEH, the downstream piezoelectric energy harvester (DPEH) generates a responsive beat frequency vibration. Energy-harvesting performance of the DPEH is better than that of the UPEH, especially at high speed flows. The maximum output power of the DPEH (371.7 µW) is 2.56 times of that of the UPEH (145.4 µW), at a specific spacing between the UPEN and the DPEH. Thereupon, the total output power of the two tandem piezoelectric energy harvester systems is significantly greater than that of the common single PEH, which provides a good foreground for further exploration of multiple piezoelectric energy harvesters system.
RESUMO
This paper describes a novel cellulose/poly(3-hydroxybutyrate) blend based electroactive polymer. The fabrication process, bending actuation test and its characteristics are investigated. To prepare this new EAP, cellulose and PHB were dissolved in trifluoroacetic acid. The solution was cast to form a film followed by depositing thin gold electrode on both sides of the film. The characteristics of the cellulose/PHB film were investigated by Fourier transform infrared spectra, scanning electron microscopy, X-ray diffraction differential scanning calorimetry, tensile test and dynamic mechanical analysis. The bending performance was evaluated in terms of free bending displacement, electrical power consumption output and lifetime test under ambient conditions. Primary results show that this cellulose/PHB blend EAP is less sensitive to humidity and it shows higher bending displacement and longer lifetime than pure cellulose EAP at room humidity condition. These results indicate that this new cellulose/PHB blend EAP has potential for many biomimetic applications.