Controlling high-speed droplet splashing and superspreading behavior on anisotropic superhydrophobic leaf surfaces by ecofriendly Pseudogemini surfactants.

BACKGROUND: Efficient deposition of high-speed droplets on superhydrophobic leaf surfaces remains an important challenge. For anisotropic wired superhydrophobic leaf surfaces, the splashing phenomenon is especially serious because it leads to the low effective utilization of pesticides by biological targets. The lost pesticides cause serious ecological environment pollution, therefore there is an urgent need to develop a green and sustainable cost-effective strategy to achieve efficient deposition of high-speed droplets on anisotropic superhydrophobic leaf surfaces at low dosage. RESULTS: One type of green pseudogemini surfactant is constructed based on fatty acids and hexamethylenediamine by electrostatic interaction to control the splashing and spreading of high-speed droplets on superhydrophobic surfaces. The formed surfactant can not only achieve complete inhibition of the bouncing of droplets, but also promote rapid spreading on superhydrophobic leaf surfaces at very low usage. The efficient deposition and superspreading phenomenon are attributed to the rapid migration and adsorption of the surfactant from the dynamic spherical micelles at the newly formed solid-liquid interface, the network-like aggregated spherical micelles, and the Marangoni effect caused by the surface tension gradient. Moreover, the surfactant shows an excellent synergistic effect with herbicides to control weeds by inhibiting droplet splashing. CONCLUSION: This work provides a simpler, more effective and sustainable approach to utilize aggregated spherical micelles rather than conventional vesicles or wormlike micelles to improve the droplet deposition on superhydrophobic leaf surfaces and reduce the impact of surfactants and pesticides on the ecological environment. © 2023 Society of Chemical Industry.

Sensitive photoelectrochemical detection of colitoxin DNA based on NCDs@CuO/ZnO heterostructured nanocomposites with efficient separation capacity of photo-induced carriers.

A metal-organic framework (MOF) of Cu-TPA (terephthalic acid) microsphere was prepared, followed by calcinating the MOF precursor of Cu-TPA/ZIF-8 mixture to obtain the CuO/ZnO. N-doped carbon dots (NCDs) were employed to combine the CuO/ZnO composite to form a tripartite heterostructured architecture of NCDs@CuO/ZnO, which led to a fierce enlargement of the photocurrent response. This  was ascribed to the thinner-shell structure of the CuO microsphere and the fact that hollow ZnO particles could sharply promote the incidence intensity of visible light. The more porous defectiveness exposed on CuO/ZnO surface was in favor of rapidly infiltrating electrolyte ions. The p-n type CuO/ZnO composite with more contact interface could abridge the transfer distance of photo-induced electron (e-1)/hole (h+) pairs and repress their recombination availably. NCDs not only could boost electron transfer rate on the electrode interface but also successfully sensitized the CuO/ZnO composite, which resulted in high conversion efficiency of photon-to-electron. The probe DNA (S1) was firmly assembled on the modified ITO electrode surface (S1/NCDs@CuO/ZnO) through an amidation reaction. Under optimal conditions, the prepared DNA biosensor displayed a wide linear range of 1.0 × 10-6 ~ 7.5 × 10-1 nM and a low limit of detection (LOD) of 1.81 × 10-7 nM for colitoxin DNA (S2) measure, which exhibited a better photoelectrochemistry (PEC) analysis performance than that obtained by differential pulse voltammetry techniques. The relative standard deviation (RSD) of the sensing platform for target DNA detection of 5.0 × 10-2 nM was 6.3%. This proposed DNA biosensor also showed good selectivity, stability, and reproducibility, demonstrating that the well-designed and synthesized photoactive materials of NCDs@CuO/ZnO are promising candidates for PEC analysis.

An enhanced photoelectrochemical biosensor for colitoxin DNA based on HKUST-1/TiO2 and derived HKUST-CuO/TiO2 heterogeneous composites.

HKUST-1 MOFs and its derivative HKUST-CuO were coupled with TiO2 nanoparticles to form the heterogeneous composites of HKUST-1/TiO2 and HKUST-CuO/TiO2 based on their well-suitable bandgap energies (Eg). Compared with mono-component HKUST-1 or HKUST-CuO, the prepared composites displayed photoelectrochemical (PEC) response due to the synergistic effect from their heterogeneous structure. Higher photocurrent response was obtained on HKUST-CuO/TiO2-modified ITO electrode (HKUST-CuO/TiO2/ITO), which could be attributed to the hollow structure with a thin shell of HKUST-CuO greatly enhancing visible spectra harvesting. The CuO component in HKUST-CuO not only could accelerate electron transfer on the heterojunction interface but also effectively separate the photo-generated charge carriers (e-1/h+). Based on the excellent PEC performance of prepared photoactive composite material, under visible-light excitation (λ ≥ 420 nm) and with a working potential of 0 V (vs. Ag/AgCl), the S1 (probe DNA)/HKUST-CuO/TiO2/ITO PEC platform was successfully fabricated for colitoxin DNA detection without using ascorbic acid (AA) as an electron donor. Compared with the analysis results on S1/HKUST-1/TiO2/ITO electrode, S1/HKUST-CuO/TiO2/ITO displayed a wider linear response range from 1.0 × 10-6 to 4.0 × 10-1 nM with a lower detection limit of 3.73 × 10-7 nM (S/N = 3), the linear regression equation was ΔI (10-6 A) =0.5549-0.1858 log (CS2/M), which confirmed the HKUST-CuO could improve sensitivity because of its prominent PEC property. The relative standard deviation (RSD) of the PEC sensor for target DNA detection of 2.0 × 10-4 nM was 7.4%. The proposed DNA biosensor also possessed good specificity and stability. Hence, this reported work was a promising strategy for molecular diagnosis in the bio-analysis field. (A) Schematic illustration of the preparation process of the proposed PEC biosensors for colitoxin DNA detection. (B) The preparation process of HKUST-1 and HKUST-CuO.

Electroinduced Reconfiguration of Complex Emulsions for Fabrication of Polymer Particles with Tunable Morphology.

Continuous morphological control of anisotropic particles is always an important challenge in the field of materials. In this study, a new strategy for continuous fabrication of polymer particles with various morphologies induced by electricity is reported using complex emulsions as template. A synthetic electro-responsive surfactant containing ferrocene group is used to prepare complex emulsions, which contain a polymerizable monomer as inner phase. With the increasing time of electrical stimulation on the complex emulsions, hollow, hemispherical, mushroom-like, and spherical particles are constructed successively after photopolymerization. The Marangoni effect caused by the heterogeneity in the interfacial tension at the droplet surface is the reason for the reconfigurable morphology of the complex emulsion. The controllable complex emulsions by electricity present a versatile platform for constructing fine control of the microstructure and shape anisotropy of particles having customized shapes and functionalities, opening a new possibility for designing sophisticated architectures.

Polypropylene Glycol-Polyoxytetramethylene Glycol Multiblock Copolymers with High Molecular Weight: Synthesis, Characterization, and Silanization.

The high crystallization at room temperature and high cost of polyoxytetramethylene glycol (PTMG) have become obstacles to its application. To overcome these problems, a segment of PTMG can be incorporated into a block copolymer. In this work, polypropylene (PPO) glycol-polyoxytetramethylene (PPO-PTMG) multiblock copolymers were designed and synthesized through a chain extension between hydroxyl (OH)-terminated PPO and PTMG oligomers. The chain extenders, feed ratios of the catalyst/chain extender/OH groups, reaction temperature, and time were optimized several times to obtain a PPO-PTMG with low crystallization and high molecular weight. Multiblock copolymers with low crystallization and high average molecular weight (Mn = 1.0-1.4 × 104 Dalton) were harvested using m-phthaloyl chloride as the chain extender. The OH-terminated PPO-PTMG multiblock copolymer with high Mn and a functionality near two was further siliconized by 3-isocyanatopropyltrimethoxysilane to synthesize a novel silyl-terminated polyether. This polyether has an appropriate vulcanizing property and potential applications in sealants/adhesive fields.