In vitro evaluation of cytomegalovirus-specific hyperimmune globulins vs. standard intravenous immunoglobulins.

BACKGROUND AND OBJECTIVES: To evaluate standard intravenous immunoglobulin (IVIG) as an alternative to intravenous cytomegalovirus hyperimmune immunoglobulin (CMVIG) for prophylaxis and therapy of cytomegalovirus (CMV) disease, we measured the ELISA and neutralizing titres of CMV-specific antibodies in CMVIG and IVIG preparations. MATERIALS AND METHODS: Anti-CMV-IgG ELISA and neutralizing titres (fibroblast-based test) in CMVIG CG (Cytogam®, n = 20), CMVIG CT (Cytotect® CP, n = 3), IVIG P (Privigen®, n = 32) and IVIG K/G (Kiovig®/Gammagard®, n = 5) were compared, and IgG subclasses 1-4 were determined by nephelometry. RESULTS: Cytomegalovirus hyperimmune immunoglobulins contained more than fourfold higher CMV ELISA and CMV-neutralizing activity per gram of IgG than the standard IVIGs. Pooled data for all four products showed a significant correlation between anti-CMV-IgG ELISA and neutralizing titres (r = 0·93, P < 0·001). There was a good correlation between the IgG3 content and CMV-neutralizing antibodies amongst lots of CMVIGs (r = 0·91, P = 0·01), but this did not extend to the IVIGs. CMVIG CG contained the highest CMV-neutralizing activity (3497 ± 395 PEIU/g IgG) of any product tested. CONCLUSION: The higher anti-CMV neutralization capacity of CMVIG per gram of IgG vs. standard IVIG suggests that standard IVIGs are not equivalent to or interchangeable with CMVIG.

Oxygen reduction via grain boundary transport in thin film platinum electrodes on yttria stabilized zirconia.

Model-type sputter deposited platinum microelectrodes with different grain sizes were investigated on single crystalline yttria stabilized zirconia (YSZ) by means of impedance spectroscopy. Measurements on single platinum microelectrodes could be continuously performed for > 100 h and from 250 to 800 °C without losing contact. From the temperature dependence, two parallel reaction pathways for oxygen reduction could be identified. Above 450 °C, a surface path with a rate determining step located at the three phase boundary is predominant. Its polarization resistance is independent of the Pt grain size and exhibits an activation energy of ca. 1.8 eV. In the low temperature regime (< 450 °C) a bulk path through Pt was verified, with an electrode polarization resistance depending on the Pt grain size. This resistance is only slightly thermally activated and the rate limiting step is most probably oxygen diffusion along Pt grain boundaries.

A novel approach for analyzing electrochemical properties of mixed conducting solid oxide fuel cell anode materials by impedance spectroscopy.

For application of acceptor-doped mixed conducting oxides as solid oxide fuel cell (SOFC) anodes, high electrochemical surface activity as well as acceptable electronic and ionic conductivity are crucial. In a reducing atmosphere, particularly the electronic conductivity of acceptor-doped oxides can become rather low and the resulting complex interplay of electrochemical reactions and charge transport processes makes a mechanistic interpretation of impedance measurements very complicated. In order to determine all relevant resistive and capacitive contributions of mixed conducting electrodes in a reducing atmosphere, a novel electrode design and impedance-based analysis technique is therefore introduced. Two interdigitating metallic current collectors are placed in a microelectrode, which allows in-plane measurements within the electrode as well as electrochemical measurements versus a counter electrode. Equivalent circuit models for quantifying the spectra of both measurement modes are developed and applied to simultaneously fit both spectra, using the same parameter set. In this manner, the electronic and ionic conductivity of the material as well as the area-specific resistance of the surface reaction and the chemical capacitance can be determined on a single microelectrode in a H2-H2O atmosphere. The applicability of this new tool was demonstrated in SrTi0.7Fe0.3O(3-δ) (STFO) thin film microelectrodes, deposited on single-crystalline yttria-stabilized zirconia (YSZ) substrates. All materials parameters that contribute to the polarization resistance of STFO electrodes in a reducing atmosphere could thus be quantified.

Continuous melting and ion chromatographic analyses of ice cores.

A new method for determining concentrations of organic and inorganic ions in ice cores by continuous melting and contemporaneous ion chromatographic analyses was developed. A subcore is melted on a melting device and the meltwater produced is collected in two parallel sample loops and then analyzed simultaneously by two ion chromatographs, one for anions and one for cations. For most of the analyzed species, lower or equal blank values were achieved with the continuous melting and analysis technique compared to the conventional analysis. Comparison of the continuous melting and ion chromatographic analysis with the conventional analysis of a real ice core segment showed good agreement in concentration profiles and total amounts of ionic species. Thus, the newly developed method is well suited for ice core analysis and has the advantages of lower ice consumption, less time-consuming sample preparation and lower risk of contamination.

Measurement of the resonant d(mu)t molecular formation rate in solid HD.

Measurements of muon-catalyzed dt fusion ( d(mu)t-->4He + n + mu(-)) in solid HD have been performed. The theory describing the energy dependent resonant molecular formation rate for the reaction (mu)t + HD-->[(d(mu)t)pee](*) is compared to experimental results in a pure solid HD target. Constraints on the rates are inferred through the use of a Monte Carlo model developed specifically for the experiment. From the time-of-flight analysis of fusion events in 16 and 37 microg x cm(-2) targets, an average formation rate consistent with 0.897+/-(0.046)(stat)+/-(0.166)(syst) times the theoretical prediction was obtained.