Investigation on the Interface Modification of TiO2 Surfaces by Functional Co-Adsorbents for High-Efficiency Dye-Sensitized Solar Cells.

The influence of interface modification of sensitized TiO2 surfaces by co-adsorbents on photovoltaic performance is detailed. We investigated different functional groups of co-adsorbents, such as carboxylic (4-guanidino butyric acid, chenodeoxycholic acid), phosphinic (dineohexyl phosphinic acid), and phosphonic (dodecyl phosphonic acid), to better highlight their influence on the device performance and accurately classify them into de-aggregating agents or agents with both de-aggregating and co-adsorbing properties. By optimizing the type of co-adsorbent and its concentration in the dye solution, we reached an efficiency of 11.0 % using 4-guanidino butyric acid or dineohexyl phosphinic acid, compared to 10.6 % when the benchmark chenodeoxycholic acid was used. The presence of co-adsorbents on the TiO2 surface was studied using ATR-FTIR spectroscopy. The role of these co-adsorbents on the band edge shift versus the recombination resistance is discussed.

Light Harvesting and Charge Recombination in CH3NH3PbI3 Perovskite Solar Cells Studied by Hole Transport Layer Thickness Variation.

A tailored optimization of perovskite solar cells requires a detailed understanding of the processes limiting the device efficiency. Here, we study the role of the hole transport layer (HTL) spiro-MeOTAD and its thickness in a mesoscopic TiO2-based solar cell architecture. We find that a sufficiently thick (200 nm) HTL not only increases the charge carrier collection efficiency but also the light harvesting efficiency. This is due to an enhanced reflection of a smooth HTL/Au-electrode interface. The rough CH3NH3PbI3 perovskite surface requires an HTL thickness of >400 nm to avoid surface recombination and guarantee a high open-circuit voltage. Analyses of the electroluminescence efficiency and the diode ideality factor show that the open-circuit voltage becomes completely limited by trap-assisted recombination in the perovskite for a thick HTL. Thus, spiro-MeOTAD is a very good HTL choice from the device physics' point of view. The fill factor analyzed by the Suns-Voc method is not transport limited, but trap-recombination limited as well. Consequently, a further optimization of the device has to focus on defects in the polycrystalline perovskite film.

Rediscovering a key interface in dye-sensitized solar cells: guanidinium and iodine competition for binding sites at the dye/electrolyte surface.

We propose a new mechanism by which the common electrolyte additive guanidinium thiocyanate (GdmSCN) improves efficiency in dye-sensitized solar cells (DSSCs). We demonstrate that binding of Gdm(+) to TiO2 is weak and does not passivate recombination sites on the TiO2 surface as has been previously claimed. Instead, we show that Gdm(+) binds strongly to the N719 and D131 dyes and probably to many similar compounds. The binding of Gdm(+) competes with iodine binding to the same molecule, reducing the surface concentration of dye-I2 complexes. This in turn reduces the electron/iodine recombination rate constant, which increases the collection efficiency and thus the photocurrent. We further observe that GdmNO3 can increase efficiency more than the current Gdm(+) source, GdmSCN, at least in some DSSCs. Overall, the results point to an improved paradigm for DSSC operation and development. The TiO2/electrolyte surface has long been held to be the key interface in DSSCs. We now assert that the dye layer/electrolyte interaction is at least, and probably more, important.

Dye-sensitized solar cells with 13% efficiency achieved through the molecular engineering of porphyrin sensitizers.

Dye-sensitized solar cells have gained widespread attention in recent years because of their low production costs, ease of fabrication and tunable optical properties, such as colour and transparency. Here, we report a molecularly engineered porphyrin dye, coded SM315, which features the prototypical structure of a donor-π-bridge-acceptor and both maximizes electrolyte compatibility and improves light-harvesting properties. Linear-response, time-dependent density functional theory was used to investigate the perturbations in the electronic structure that lead to improved light harvesting. Using SM315 with the cobalt(II/III) redox shuttle resulted in dye-sensitized solar cells that exhibit a high open-circuit voltage VOC of 0.91 V, short-circuit current density JSC of 18.1 mA cm(-2), fill factor of 0.78 and a power conversion efficiency of 13%.

4,9-Dihydro-4,4,9,9-tetrahexyl-s-indaceno[1,2-b:5,6-b']dithiophene as a π-spacer of donor-π-acceptor dye and its photovoltaic performance with liquid and solid-state dye-sensitized solar cells.

A new D-π-A organic dye, LC-5, containing 4,9-dihydro-4,4,9,9-tetrahexyl-s-indaceno[1,2-b:5,6-b']-dithiophene as a novel π-conjugated spacer has been synthesized and tested as a sensitizer in dye-sensitized solar cells (DSC). Volatile and ionic liquid electrolytes have been used in conjunction with the synthesized dye, and the electrolyte influence on the photovoltaic performance of DSCs was investigated. A detailed investigation, including transient photocurrent/photovoltage decay measurements and electrochemical impedance spectroscopy data, provide important conclusions about the influence of electrolytes on the photovoltaic parameters.

Sequential deposition as a route to high-performance perovskite-sensitized solar cells.

Following pioneering work, solution-processable organic-inorganic hybrid perovskites-such as CH3NH3PbX3 (X = Cl, Br, I)-have attracted attention as light-harvesting materials for mesoscopic solar cells. So far, the perovskite pigment has been deposited in a single step onto mesoporous metal oxide films using a mixture of PbX2 and CH3NH3X in a common solvent. However, the uncontrolled precipitation of the perovskite produces large morphological variations, resulting in a wide spread of photovoltaic performance in the resulting devices, which hampers the prospects for practical applications. Here we describe a sequential deposition method for the formation of the perovskite pigment within the porous metal oxide film. PbI2 is first introduced from solution into a nanoporous titanium dioxide film and subsequently transformed into the perovskite by exposing it to a solution of CH3NH3I. We find that the conversion occurs within the nanoporous host as soon as the two components come into contact, permitting much better control over the perovskite morphology than is possible with the previously employed route. Using this technique for the fabrication of solid-state mesoscopic solar cells greatly increases the reproducibility of their performance and allows us to achieve a power conversion efficiency of approximately 15 per cent (measured under standard AM1.5G test conditions on solar zenith angle, solar light intensity and cell temperature). This two-step method should provide new opportunities for the fabrication of solution-processed photovoltaic cells with unprecedented power conversion efficiencies and high stability equal to or even greater than those of today's best thin-film photovoltaic devices.

Measured binding coefficients for iodine and ruthenium dyes; implications for recombination in dye sensitised solar cells.

We have measured the binding coefficients of iodine to three dyes used in Dye Sensitised Solar Cells (DSSCs). Binding coefficients are quantified via the effect of iodine binding on the UV-vis spectrum of the dye. From iodine titration curves of dye sensitised TiO(2) films we find that the binding coefficients of iodine to the dyes C101, N719 and AR24 (vide infra) are in the range of 2000-4000 M(-1). From FTIR results and molecular modelling we show the iodine binds to the thiocyanate group in all these dyes. For the AR24 dye we present evidence that iodine also binds to the amine moiety on this dye. With these binding coefficients we show that the dye-iodine complex will be present at much higher concentrations than free iodine in the pore structure of a DSSC. As we have recently shown that iodine (rather than tri-iodide) is the dominant acceptor in electron recombination, the concentration dye-iodine complexes could influence recombination rates and thus V(oc). By comparison of recombination data on full cells, we show that AR24 accelerates recombination by a factor of 7 over N719, presumably due to the iodine binding to the amine group. We leave open the question why iodine binding to the amine group seems to have a stronger effect on the recombination than does binding to the thiocyanate.

Donor-π-acceptors containing the 10-(1,3-dithiol-2-ylidene)anthracene unit for dye-sensitized solar cells.

Two donor-acceptor molecular tweezers incorporating the 10-(1,3-dithiol-2-ylidene)anthracene unit as donor group and two cyanoacrylic units as accepting/anchoring groups are reported as metal-free sensitizers for dye-sensitized solar cells. By changing the phenyl spacer with 3,4-ethylenedioxythiophene (EDOT) units, the absorption spectrum of the sensitizer is red-shifted with a corresponding increase in the molar absorptivity. Density functional calculations confirmed the intramolecular charge-transfer nature of the lowest-energy absorption bands. The new dyes are highly distorted from planarity and are bound to the TiO(2) surface through the two anchoring groups in a unidentate binding form. A power-conversion efficiency of 3.7% was obtained with a volatile CH(3)CN-based electrolyte, under air mass 1.5 global sunlight. Photovoltage decay transients and ATR-FTIR measurements allowed us to understand the photovoltaic performance, as well as the surface binding, of these new sensitizers.

Lead iodide perovskite sensitized all-solid-state submicron thin film mesoscopic solar cell with efficiency exceeding 9%.

We report on solid-state mesoscopic heterojunction solar cells employing nanoparticles (NPs) of methyl ammonium lead iodide (CH(3)NH(3))PbI(3) as light harvesters. The perovskite NPs were produced by reaction of methylammonium iodide with PbI(2) and deposited onto a submicron-thick mesoscopic TiO(2) film, whose pores were infiltrated with the hole-conductor spiro-MeOTAD. Illumination with standard AM-1.5 sunlight generated large photocurrents (J(SC)) exceeding 17 mA/cm(2), an open circuit photovoltage (V(OC)) of 0.888 V and a fill factor (FF) of 0.62 yielding a power conversion efficiency (PCE) of 9.7%, the highest reported to date for such cells. Femto second laser studies combined with photo-induced absorption measurements showed charge separation to proceed via hole injection from the excited (CH(3)NH(3))PbI(3) NPs into the spiro-MeOTAD followed by electron transfer to the mesoscopic TiO(2) film. The use of a solid hole conductor dramatically improved the device stability compared to (CH(3)NH(3))PbI(3) -sensitized liquid junction cells.

Subnanometer Ga2O3 tunnelling layer by atomic layer deposition to achieve 1.1 V open-circuit potential in dye-sensitized solar cells.

Herein, we present the first use of a gallium oxide tunnelling layer to significantly reduce electron recombination in dye-sensitized solar cells (DSC). The subnanometer coating is achieved using atomic layer deposition (ALD) and leading to a new DSC record open-circuit potential of 1.1 V with state-of-the-art organic D-π-A sensitizer and cobalt redox mediator. After ALD of only a few angstroms of Ga(2)O(3), the electron back reaction is reduced by more than an order of magnitude, while charge collection efficiency and fill factor are increased by 30% and 15%, respectively. The photogenerated exciton separation processes of electron injection into the TiO(2) conduction band and the hole injection into the electrolyte are characterized in detail.

Molecular-scale interface engineering of nanocrystalline titania by co-adsorbents for solar energy conversion.

The use of mixed self-assembled monolayers, combining hydrophobic co-adsorbents with the sensitizer, has been demonstrated to enhance the efficiency of dye-sensitized solar cells (DSCs). Herein, the influence of the anchoring groups of the co-adsorbents on the performance of the DSCs is carefully examined by selecting two model molecules: neohexyl phosphonic acid (NHOOP) and bis-(3,3-dimethyl-butyl)-phosphinic acid (DINHOP). The effect of these co-adsorbents on the photovoltaic performance (J-V curves, incident photon-to-electron conversion efficiency) is investigated. Photoelectron spectroscopy and electrochemical impedance spectroscopy are performed to assess the spatial configuration of adsorbed dye and co-adsorbent molecules. The photoelectron spectroscopy studies indicate that the ligands of the ruthenium complex, containing thiophene groups, point out away from the surface of TiO(2) in comparison with the NCS group.

D-π-A dye system containing cyano-benzoic acid as anchoring group for dye-sensitized solar cells.

A D-π-A dye (KM-1) incorporating cyano-benzoic acid as a new acceptor/anchoring group has been synthesized for dye-sensitized solar cells (DSCs) with a high molar extinction coefficient of 66,700 M(-1) cm(-1) at 437 nm. Theoretical calculations show that the hydrogen bond between -CN and surface hydroxyl leads to the most stable configuration on the surface of TiO(2). In addition, the adsorption of the dye on TiO(2) follows a Brunauer-Emmett-Teller (BET) isotherm. Multilayer adsorption of KM-1 on TiO(2) seems to take place particularly at higher dye concentrations. DSC device using KM-1 reached a maximum incident photon-to-current conversion efficiency (IPCE) of 84%, with a solar to electric power conversion efficiency (PCE) of 3.3% at AM1.5 G illumination (100 mW cm(-2)). This new type of anchoring group paves a way to design new dyes that combine good visible light harvesting with strong binding to the metal oxide surface.

Energy and hole transfer between dyes attached to titania in cosensitized dye-sensitized solar cells.

Cosensitization of broadly absorbing ruthenium metal complex dyes with highly absorptive near-infrared (NIR) organic dyes is a clear pathway to increase near-infrared light harvesting in liquid-based dye-sensitized solar cells (DSCs). In cosensitized DSCs, dyes are intimately mixed, and intermolecular charge and energy transfer processes play an important role in device performance. Here, we demonstrate that an organic NIR dye incapable of hole regeneration is able to produce photocurrent via intermolecular energy transfer with an average excitation transfer efficiency of over 25% when cosensitized with a metal complex sensitizing dye (SD). We also show that intermolecular hole transfer from the SD to NIR dye is a competitive process with dye regeneration, reducing the internal quantum efficiency and the electron lifetime of the DSC. This work demonstrates the general feasibility of using energy transfer to boost light harvesting from 700 to 800 nm and also highlights a key challenge for developing highly efficient cosensitized dye-sensitized solar cells.

An organic D-π-A dye for record efficiency solid-state sensitized heterojunction solar cells.

The high molar absorption coefficient organic D-π-A dye C220 exhibits more than 6% certified electric power conversion efficiency at AM 1.5G solar irradiation (100 mW cm(-2)) in a solid-state dye-sensitized solar cell using 2,2',7,7'-tetrakis(N,N-dimethoxyphenylamine)-9,9'-spirobifluorene (spiro-MeOTAD) as the organic hole-transporting material. This contributes to a new record (6.08% by NREL) for this type of sensitized heterojunction photovoltaic device. Efficient charge generation is proved by incident photon-to-current conversion efficiency spectra. Transient photovoltage and photocurrent decay measurements showed that the enhanced performance achieved with C220 partially stems from the high charge collection efficiency over a wide potential range.

An organic redox electrolyte to rival triiodide/iodide in dye-sensitized solar cells.

Dye-sensitized solar cells (DSCs) have achieved impressive conversion efficiencies for solar energy of over 11% with an electrolyte that contains triiodide/iodide as a redox couple. Although triiodide/iodide redox couples work efficiently in DSCs, they suffer from two major disadvantages: electrolytes that contain triiodide/iodide corrode electrical contacts made of silver (which reduces the options for the scale up of DSCs to module size) and triiodide partially absorbs visible light. Here, we present a new disulfide/thiolate redox couple that has negligible absorption in the visible spectral range, a very attractive feature for flexible DSCs that use transparent conductors as current collectors. Using this novel, iodide-free redox electrolyte in conjunction with a sensitized heterojunction, we achieved an unprecedented efficiency of 6.4% under standard illumination test conditions. This novel redox couple offers a viable pathway to develop efficient DSCs with attractive properties for scale up and practical applications.

Efficient electron transfer and sensitizer regeneration in stable pi-extended tetrathiafulvalene-sensitized solar cells.

The development of metal-free organic sensitizers is a key issue in dye-sensitized solar cell research. We report successful photovoltaic conversion with a new class of stable tetrathiafulvalene derivatives, showing surprising electrochemical and kinetic properties. With time-resolved spectroscopy we could observe highly efficient regeneration of the photo-oxidized tetrathiafulvalene sensitizers, which were attached to a mesoporous TiO(2) film, by a redox mediator in the pores (iodide/tri-iodide), even though the measured driving force for regeneration was only approximately 150 mV. This important proof-of-concept shows that sensitizers with a small driving force, i.e. the oxidation potential of the sensitizer is separated from the redox potenial of the mediator by as little as 150 mV, can operate functionally in dye-sensitized solar cells and eventually aid to reduce photovoltage losses due to poor energetic alignment of the materials.

Efficient and stable solid-state dye-sensitized solar cells based on a high-molar-extinction-coefficient sensitizer.

The high-molar-extinction-coefficient heteroleptic ruthenium dye, cis-Ru (4,4'-bis(5-octylthieno[3,2-b] thiophen-2-yl)-2,2'-bipyridine) (4,4'-dicarboxyl-2,2'-bipyridine) (NCS)(2), exhibits an AM 1.5 solar (100 mW cm(-2))-to-electric power-conversion efficiency of 4.6% in a solid-state dye-sensitized solar cell (SSDSC) with 2,2', 7,7'-tetrakis-(N,N-di-p-methoxyphenylamine)9,9'-spirobifluorene (spiro-MeOTAD) as the organic hole-transporting material. These SSDSC devices exhibit good durability during accelerated tests under visible-light soaking for 1000 h at 60 degrees C. This demonstration elucidates a class of photovoltaic devices with potential for stable and low-cost power generation. The electron recombination dynamics and charge collection that take place at the dye-sensitized heterojunction are studied by means of impedance and transient photovoltage decay techniques.

The influence of charge transport and recombination on the performance of dye-sensitized solar cells.

Electrochemical impedance spectroscopy (EIS) and transient voltage decay measurements are applied to compare the performance of dye sensitized solar cells (DSCs) using organic electrolytes, ionic liquids and organic-hole conductors as hole transport materials (HTM). Nano-crystalline titania films sensitized by the same heteroleptic ruthenium complex NaRu(4-carboxylic acid-4'-carboxylate) (4,4'-dinonyl-2,2'-bipyridyl)(NCS)(2) , coded Z-907Na are employed as working electrodes. The influence of the nature of the HTM on the photovoltaic figures of merit, that is, the open circuit voltage, short circuit photocurrent and fill factor is evaluated. In order to derive the electron lifetime, as well as the electron diffusion coefficient and charge collection efficiency, EIS measurements are performed in the dark and under illumination corresponding to realistic photovoltaic operating conditions of these mesoscopic solar cells. A theoretical model is established to interpret the frequency response off the impedance under open circuit conditions, which is conceptually similar to photovoltage transient decay measurements. Important information on factors that govern the dynamics of electron transport within the nanocrystalline TiO(2) film and charge recombination across the dye sensitized heterojunction is obtained.

Enhance the optical absorptivity of nanocrystalline TiO2 film with high molar extinction coefficient ruthenium sensitizers for high performance dye-sensitized solar cells.

We report two new heteroleptic polypyridyl ruthenium complexes, coded C101 and C102, with high molar extinction coefficients by extending the pi-conjugation of spectator ligands, with a motivation to enhance the optical absorptivity of mesoporous titania film and charge collection yield in a dye-sensitized solar cell. On the basis of this C101 sensitizer, several DSC benchmarks measured under the air mass 1.5 global sunlight have been reached. Along with an acetonitrile-based electrolyte, the C101 sensitizer has already achieved a strikingly high efficiency of 11.0-11.3%, even under a preliminary testing. More importantly, based on a low volatility 3-methoxypropionitrile electrolyte and a solvent-free ionic liquid electrolyte, cells have corresponding >9.0% and approximately 7.4% efficiencies retained over 95% of their initial performances after 1000 h full sunlight soaking at 60 degrees C. With the aid of electrical impedance measurements, we further disclose that, compared to the cell with an acetonitrile-based electrolyte, a dye-sensitized solar cell with an ionic liquid electrolyte shows a feature of much shorter effective electron diffusion lengths due to the lower electron diffusion coefficients and shorter electron lifetimes in the mesoporous titania film, explaining the photocurrent difference between these two type devices. This highlights the next necessary efforts to further improve the efficiency of cells with ionic liquid electrolytes, facilitating the large-scale production and application of flexible thin film mesoscopic solar cells.