Correction: A wearable colorimetric sweat pH sensor-based smart textile for health state diagnosis.

Correction for 'A wearable colorimetric sweat pH sensor-based smart textile for health state diagnosis' by Ji-Hwan Ha et al., Mater. Horiz., 2023, 10, 4163-4171, https://doi.org/10.1039/d3mh00340j.

Wafer-scale, highly uniform, and well-arrayed suspended nanostructures for enhancing the performance of electronic devices.

Suspended nanostructures play an important role in enhancing the performance of a diverse group of nanodevices. However, realizing a good arrangement and suspension for nanostructures of various shapes remains a significant challenge. Herein, a rapid and simple method for fabricating wafer-scale, highly uniform, well-arrayed suspended nanostructures via nanowelding lithography is reported. Suspended nanostructures with various shapes (nanowires, nanoholes, nanomesh, and nanofilms) and materials (gold, silver, and palladium metals) were employed to demonstrate the applicability of our method. Moreover, gas sensors and thermoacoustic speakers with suspended nanowires outperformed those with unsuspended nanostructures. The proposed method is expected to help advance the development of future nanodevices based on suspended nanostructures.

Direct Chemisorption-Assisted Nanotransfer Printing with Wafer-Scale Uniformity and Controllability.

Nanotransfer printing techniques have attracted significant attention due to their outstanding simplicity, cost-effectiveness, and high throughput. However, conventional methods via a chemical medium hamper the efficient fabrication with large-area uniformity and rapid development of electronic and photonic devices. Herein, we report a direct chemisorption-assisted nanotransfer printing technique based on the nanoscale lower melting effect, which is an enabling technology for two- or three-dimensional nanostructures with feature sizes ranging from tens of nanometers up to a 6 in. wafer-scale. The method solves the major bottleneck (large-scale uniform metal catalysts with nanopatterns) encountered by metal-assisted chemical etching. It also achieves wafer-scale, uniform, and controllable nanostructures with extremely high aspect ratios. We further demonstrate excellent uniformity and high performance of the resultant devices by fabricating 100 photodetectors on a 6 in. Si wafer. Therefore, our method can create a viable route for next-generation, wafer-scale, uniformly ordered, and controllable nanofabrication, leading to significant advances in various applications, such as energy harvesting, quantum, electronic, and photonic devices.

Wide-viewing full-color depthmap computer-generated holograms.

An efficient synthesis algorithm for wide-viewing full-color depthmap computer-generated holograms is proposed. We develop a precise computational algorithm integrating wave-optic geometry-mapping, color-matching, and noise-filtering to multiplex multiview elementary computer-generated holograms (CGHs) into a single high-definition CGH without three-dimensional perspective distortion or color dispersion. Computational parallelism is exploited to achieve significant computational efficiency improvement in the production throughput of full-color wide-viewing angle CGHs. The proposed algorithm is verified through the full-color binary hologram reconstruction experiments utilizing an off-axis R·G·B simultaneous illumination method, which suggests the feasibility of the full-color sub-wavelength binary spatial light modulator technology.

Nanopattern-Embedded Micropillar Structures for Security Identification.

A novel method was developed for fabricating nanopatterns embedded on micropillar-structured surfaces using nanowelding technology for security identification. Commonly used substrates, that is, polyethylene films, glass wafers, Si wafers, and curved surfaces, were employed and their characteristics were evaluated. Cr was deposited onto the selected substrate to strengthen the adhesion force, and an adhesive layer of ultra-thin metal was deposited on top of the Cr layer. Lastly, nanopatterns were embedded on the substrates by nanowelding. The morphologies, cross sections, and three-dimensional (3D) images of the fabricated nanostructures were evaluated, and their crystalline structures and compositions were analyzed. Using the same method, nanopatterns embedded on micropillar-structured surfaces were fabricated for the first time as security patterns to improve security identification. The fabricated security patterns were characterized in three stages. First, micropillar structures and structural color were simply observed via optical microscopy to achieve a preliminary judgment. The appearance of structural color was due to the nanostructures fabricated on the micropillar surface. Next, the designed nanopatterns on the micropillar-structured surfaces were observed by scanning electron microscopy. Lastly, the changes in the spectral peaks were precisely observed using a spectrometer to achieve an enhanced security pattern. The fabricated security patterns can be suitable for valuable products, such as branded wines, watches, and bags. In addition, the proposed method offers a simple approach for transferring metal nanopatterns to common substrates. Moreover, the fabricated security patterns can have potential applications in semiconductor electrodes, transparent electrodes, and security identification codes.

Printed fabric heater based on Ag nanowire/carbon nanotube composites.

The increasing demand for smart fabrics has inspired extensive research in the field of nanomaterial-based wearable heaters. However, existing stretchable heaters employ polymer substrates, and hence require additional substrate-fabric bonding that can result in high thermal contact resistance. Moreover, currently used stretchable fabric heaters suffer from high sheet resistance and require complex fabrication processes. In addition, conventional fabrication methods do not allow for patternability, thus hindering the fabrication of wearable heaters with diverse designs. Herein, we propose an improved spray coating method well suited for the preparation of patternable heaters on commercial fabrics, combining the structural stability of carbon nanotubes with the high electrical conductivity of Ag nanowires to fabricate a stretchable fabric heater with excellent mechanical (stretchability ≈ 50%) and electrical (sheet resistance ≈ 22 Ω sq-1) properties. The fabricated wearable heater reaches typical operating temperatures of 35 °C-55 °C at a low driving voltage of 3-5 V with a proper surface power density of 26.6-72.2 [Formula: see text] (heater area: [Formula: see text]) and maintains a stable heating temperature for more than 30 h. This heater shows a stable performance even when folded or rolled, thus being well suited for the practical wearable applications.

Heterogeneous Nanostructures Fabricated via Binding Energy-Controlled Nanowelding.

A novel concept for fabricating heterogeneous nanostructures based on different melting temperatures is developed. Au-Ag composite cross-structures are fabricated by nanowelding technologies. During the fabrication of Au-Ag composite cross-structures, Ag nanowires transform into ordered particles decorating the Au nanowire surfaces with an increase in the welding temperature because of the different melting temperatures of Au and Ag. To compare and explain the melting temperatures, the thicknesses of Au and Ag nanowires as parameters are analyzed. Scanning electron microscopy and focused ion beam imaging are used to observe the morphologies and cross sections of the fabricated samples. The evolution of 3D nanostructures is observed by atomic force microscopy, whereas the compositions and binding energies of the nanostructures are determined by X-ray diffraction and X-ray photoelectron spectroscopies. In addition, the atomic structures are analyzed by transmission electron microscopy, and the optical properties of the fabricated nanostructures are evaluated by spectrometry. Furthermore, color filter electrodes are fabricated, and their polarization properties are evaluated by sheet resistance measurements and observing the color and brightness of light-emitting diodes. The proposed method is suitable for application in various fields such as biosensors, optics, and medicine.

Metasurface eyepiece for augmented reality.

Recently, metasurfaces composed of artificially fabricated subwavelength structures have shown remarkable potential for the manipulation of light with unprecedented functionality. Here, we first demonstrate a metasurface application to realize a compact near-eye display system for augmented reality with a wide field of view. A key component is a see-through metalens with an anisotropic response, a high numerical aperture with a large aperture, and broadband characteristics. By virtue of these high-performance features, the metalens can overcome the existing bottleneck imposed by the narrow field of view and bulkiness of current systems, which hinders their usability and further development. Experimental demonstrations with a nanoimprinted large-area see-through metalens are reported, showing full-color imaging with a wide field of view and feasibility of mass production. This work on novel metasurface applications shows great potential for the development of optical display systems for future consumer electronics and computer vision applications.

Plasmonic color filters fabricated via oxide-based nanotransfer printing.

Plasmonic filters have recently become a topic of significant interest because they are suitable for a wide range of applications. However, effective fabrication of plasmonic filters remains a challenge. In this paper, we demonstrate a simple method for fabricating plasmonic color filters based on nanotransfer printing (nTP) , using SiO2 as a hard mask for Al etching. nTP was performed on a 100 nm Al layer deposited on a glass wafer substrate with a 10 nm Al layer and a 20 nm SiO2 layer with a nanohole pattern. The 10 nm Al layer and 20 nm SiO2 layers were previously transferred from a polymer stamp prepared to create patterns of subwavelength-sized holes. The plasmonic filters were ultimately fabricated using the SiO2 layer as a hard mask to selectively etch the Al layer. The optical properties of the fabricated plasmonic filters were evaluated using experimental and simulation tools. In addition, we analyzed the results of nTP on the Al and SiO2 films by varying the temperature, pressure, and SiO2-film thickness. We believe that this technique is a promising method for fabricating nanostructures and for widening the scope of practical application of plasmonics because of its high efficiency and cost-effectiveness.

Eight Inch Wafer-Scale Flexible Polarization-Dependent Color Filters with Ag-TiO2 Composite Nanowires.

In this study, 8 in. wafer-scale flexible polarization-dependent color filters with Ag-TiO2 composite nanowires have been fabricated using nanoimprint and E-beam evaporation. The filters change their color via a simple rotation of the polarizer. In addition, the color of the filter can be controlled by altering the thickness of the Ag and TiO2 nanowires deposited on the polymer patterns. Polarization-dependent color filters were realized by selective inhibition of transmission using the plasmonic resonance at the insulator/metal/insulator nanostructure interface, which occurs at particular wavelengths for the transverse magnetic polarizations. Special colors, including purple, blue, green, yellow, and pink, could be obtained with high transmission beyond 65% by varying the thickness of the deposited Ag and TiO2 nanowires on the periodic polymer pattern under transverse magnetic polarization. In addition, a continuous color change was achieved by varying the polarization angle. Last, numerical simulations were implemented in comparison with the experimental results, and the mechanism was explained. We believe that this simple and cost-effective method can be applied to processes such as anticounterfeiting and holographic imaging as well as to color displays.

Flexible Plasmonic Color Filters Fabricated via Nanotransfer Printing with Nanoimprint-Based Planarization.

We investigated the preparation and performance of large-area transmission-type flexible plasmonic color filters (PCFs). These large-area PCFs were fabricated based on a nanotransfer printing (nTP) process that involves nanoimprint-based planarization. This process is a simple surface treatment for easy transfer of a metal to a flexible plastic substrate and formation of patterned aluminum nanodots and nanoholes on a substrate surface with poor roughness. Rabbit-ear structures can form during the nTP process, and this phenomenon was analyzed by numerical simulation. As defects were not detected in a 10 000-round bending test, the PCFs fabricated using this nTP process have excellent mechanical properties.