High-Performance One-Body Electrochemical Torsional Artificial Muscles Built Using Carbon Nanotubes and Ion-Exchange Polymers.

Electrochemical torsional artificial muscles have the potential to replace electric motors in the field of miniaturization. In particular, carbon nanotubes (CNTs) are some of the best materials for electrochemical torsional artificial muscles due to their remarkable mechanical strength and high electrical conductivity. However, previous studies on CNT torsional muscle utilize only half of the whole potential range for torsional actuation because the actuations in the positive and negative voltage ranges offset each other. Here, we used an ion-exchange polymer, poly(sodium 4-styrenesulfonate) (PSS), which leads to the participation of only positive ions in the actuation of CNT muscles so that the whole potential range can be used for torsional actuation. As a result, PSS-coated CNT muscle can provide 1.9 times higher torsional actuation compared to neat CNT torsional muscle. This PSS-coated CNT muscle not only provides high performance but also facilitates a one-body system for electrochemical torsional actuation. From these advantages, we implement a one-body torsional muscle for the realization of the forward motion of a model boat. This high performance and one-body structure for electrochemical torsional muscles can be used for further applications, such as soft robotics and implantable devices.

More Powerful Twistron Carbon Nanotube Yarn Mechanical Energy Harvesters.

Stretching a coiled carbon nanotube (CNT) yarn can provide large, reversible electrochemical capacitance changes, which convert mechanical energy to electricity. Here, it is shown that the performance of these "twistron" harvesters can be increased by optimizing the alignment of precursor CNT forests, plastically stretching the precursor twisted yarn, applying much higher tensile loads during precoiling twist than for coiling, using electrothermal pulse annealing under tension, and incorporating reduced graphene oxide nanoplates. The peak output power for a 1 and a 30 Hz sinusoidal deformation are 0.73 and 3.19 kW kg-1 , respectively, which are 24- and 13-fold that of previous twistron harvesters at these respective frequencies. This performance at 30 Hz is over 12-fold that of other prior-art mechanical energy harvesters for frequencies between 0.1 and 600 Hz. The maximum energy conversion efficiency is 7.2-fold that for previous twistrons. Twistron anode and cathode yarn arrays are stretched 180° out-of-phase by locating them in the negative and positive compressibility directions of hinged wine-rack frames, thereby doubling the output voltage and reducing the input mechanical energy.

Bidirectional Core Sandwich Structure of Reduced Graphene Oxide and Spinnable Multiwalled Carbon Nanotubes for Electromagnetic Interference Shielding Effectiveness.

Thin and flexible electromagnetic shielding materials have recently emerged because of their promising applications in drones, portable electronics, military defense facilities, etc. This research develops an electromagnetic interference (EMI) shielding material by a bidirectional lattice sandwich structure (BLSS), which is formed by liquid crystalline graphene oxide (LCGO) and an orthogonal pattern of spinnable multiwalled (OPSM) nanotubes in consideration of the movement of electromagnetic waves. The average EMI shielding effectiveness (SE) of the developed material with 0.5 wt % reduced LCGO (r-LCGO) and an OPSM nanotube composed of 64 layers was approximately 66.1 dB in the X-band frequency range (8.2-12.4 GHz, wavelength: 3.5-2.5 cm), which corresponds to a shielding efficiency of 99.9999%. Also, its absorption effectiveness is 99.7% of the total EMI SE, indicating that it has a remarkable ability to prevent secondary damage induced by EM reflection. The specific EMI SE (SSE/t) of the composite material considering the contribution of thickness (t) ranged from 21 953 to 2259 dB cm2/g.

Two-Ply Carbon Nanotube Fiber-Typed Enzymatic Biofuel Cell Implanted in Mice.

Implantable devices have emerged as a promising industry. It is inevitable that these devices will require a power source to operate in vivo. Thus, to power implantable medical devices, biofuel cells (BFCs) that generate electricity using glucose without an external power supply have been considered. Although implantable BFCs have been developed for application in vivo, they are limited by their bulky electrodes and low power density. In the present study, we attempted to apply to living mice an implantable enzymatic BFC (EBFC) that was previously reported to be a high-power EBFC comprising carbon nanotube yarn electrodes. To improve their mechanical properties and for convenient implantation, the electrodes were coated with Nafion and twisted into a micro-sized, two-ply, one-body system. When the two-ply EBFC system was implanted in the abdominal cavity of mice, it provided a high-power density of 0.3 mW/cm2. The two-ply EBFC system was injected through a needle using a syringe without surgery and the inflammatory response in vivo initially induced by the injection of the EBFC system was attenuated after 7 days, indicating the biocompatibility of the system in vivo.

Electrical energy harvesting from ferritin biscrolled carbon nanotube yarn.

Various studies about harvesting energy for future energy production have been conducted. In particular, replacing batteries in implantable medical devices with electrical harvesting is a great challenge. Here, we have improved the electrical harvesting performance of twisted carbon nanotube yarn, which was previously reported to be an electrical energy harvester, by biscrolling positively charged ferritin protein in a biofluid environment. The harvester electrodes are made by biscrolling ferritin (40 wt%) in carbon nanotube yarn and twisting it into a coiled structure, which provides stretchability. The coiled ferritin/carbon nanotube yarn generated a 2.8-fold higher peak-to-peak open circuit voltage (OCV) and a 1.5-fold higher peak power than that generated by bare carbon nanotube yarn in phosphate-buffered saline (PBS) buffer. The improved performance is the result of the increased capacitance change and the shifting of the potential of zero charges that are induced by the electrochemically capacitive, positively charged ferritin. As a result, we confirm that the electrical performance of the carbon nanotube harvester can be improved using biomaterials. This carbon nanotube yarn harvester, which contains protein, has the potential to replace batteries in implantable devices.

Enhancing the Work Capacity of Electrochemical Artificial Muscles by Coiling Plies of Twist-Released Carbon Nanotube Yarns.

Twisted-yarn-based artificial muscles can potentially be used in diverse applications, such as valves in microfluidic devices, smart textiles, air vehicles, and exoskeletons, because of their high torsional and tensile strokes, high work capacities, and long cycle life. Here, we demonstrate electrochemically powered, hierarchically twisted carbon nanotube yarn artificial muscles that have a contractile work capacity of 3.78 kJ/kg, which is 95 times the work capacity of mammalian skeletal muscles. This record work capacity and a tensile stroke of 15.1% were obtained by maximizing yarn capacitance by optimizing the degree of inserted twist in component yarns that are plied until fully coiled. These electrochemically driven artificial muscles can be operated in reverse as mechanical energy harvesters that need no externally applied bias. In aqueous sodium chloride electrolyte, a peak electrical output power of 0.65 W/kg of energy harvester was generated by 1 Hz sinusoidal elongation.

Harvesting electrical energy from torsional thermal actuation driven by natural convection.

The development of practical, cost-effective systems for the conversion of low-grade waste heat to electrical energy is an important area of renewable energy research. We here demonstrate a thermal energy harvester that is driven by the small temperature fluctuations provided by natural convection. This harvester uses coiled yarn artificial muscles, comprising well-aligned shape memory polyurethane (SMPU) microfibers, to convert thermal energy to torsional mechanical energy, which is then electromagnetically converted to electrical energy. Temperature fluctuations in a yarn muscle, having a maximum hot-to-cold temperature difference of about 13 °C, were used to spin a magnetic rotor to a peak torsional rotation speed of 3,000 rpm. The electromagnetic energy generator converted the torsional energy to electrical energy, thereby producing an oscillating output voltage of up to 0.81 V and peak power of 4 W/kg, based on SMPU mass.