Laser-Formed Sensors with Electrically Conductive MWCNT Networks for Gesture Recognition Applications.

Currently, an urgent need in the field of wearable electronics is the development of flexible sensors that can be attached to the human body to monitor various physiological indicators and movements. In this work, we propose a method for forming an electrically conductive network of multi-walled carbon nanotubes (MWCNT) in a matrix of silicone elastomer to make stretchable sensors sensitive to mechanical strain. The electrical conductivity and sensitivity characteristics of the sensor were improved by using laser exposure, through the effect of forming strong carbon nanotube (CNT) networks. The initial electrical resistance of the sensors obtained using laser technology was ~3 kOhm (in the absence of deformation) at a low concentration of nanotubes of 3 wt% in composition. For comparison, in a similar manufacturing process, but without laser exposure, the active material had significantly higher values of electrical resistance, which was ~19 kOhm in this case. The laser-fabricated sensors have a high tensile sensitivity (gauge factor ~10), linearity of >0.97, a low hysteresis of 2.4%, tensile strength of 963 kPa, and a fast strain response of 1 ms. The low Young's modulus values of ~47 kPa and the high electrical and sensitivity characteristics of the sensors made it possible to fabricate a smart gesture recognition sensor system based on them, with a recognition accuracy of ~94%. Data reading and visualization were performed using the developed electronic unit based on the ATXMEGA8E5-AU microcontroller and software. The obtained results open great prospects for the application of flexible CNT sensors in intelligent wearable devices (IWDs) for medical and industrial applications.

Flexible Strain-Sensitive Silicone-CNT Sensor for Human Motion Detection.

This article describes the manufacturing technology of biocompatible flexible strain-sensitive sensor based on Ecoflex silicone and multi-walled carbon nanotubes (MWCNT). The sensor demonstrates resistive behavior. Structural, electrical, and mechanical characteristics are compared. It is shown that laser radiation significantly reduces the resistance of the material. Through laser radiation, electrically conductive networks of MWCNT are formed in a silicone matrix. The developed sensor demonstrates highly sensitive characteristics: gauge factor at 100% elongation -4.9, gauge factor at 90° bending -0.9%/deg, stretchability up to 725%, tensile strength 0.7 MPa, modulus of elasticity at 100% 46 kPa, and the temperature coefficient of resistance in the range of 30-40 °C is -2 × 10-3. There is a linear sensor response (with 1 ms response time) with a low hysteresis of ≤3%. An electronic unit for reading and processing sensor signals based on the ATXMEGA8E5-AU microcontroller has been developed. The unit was set to operate the sensor in the range of electrical resistance 5-150 kOhm. The Bluetooth module made it possible to transfer the received data to a personal computer. Currently, in the field of wearable technologies and health monitoring, a vital need is the development of flexible sensors attached to the human body to track various indicators. By integrating the sensor with the joints of the human hand, effective movement sensing has been demonstrated.

The study of the interaction mechanism between bovine serum albumin and single-walled carbon nanotubes depending on their diameter and concentration in solid nanocomposites by vibrational spectroscopy.

The results of the study of composites based on bovine serum albumin (BSA) and single-walled carbon nanotubes (SWCNT) are presented. Nanocomposites were created by evaporation of the water-albumin dispersion with nanotubes using diode laser with temperature control. Two types of nanotubes were used. SWCNT I were synthesized using the electric arc method, SWCNT II were synthesized using the gas phase method. SWCNT I had a diameter and length less than SWCNT II. The mechanism of interaction between BSA and SWCNT in solid nanocomposites is considered. An experimental and theoretical studies of the interaction between aspartic (Asp) and glutamic (Glu) amino acids located on the outer surface of BSA and nanotubes using of vibrational spectroscopy (Fourier-transform infrared (FTIR) and Raman spectroscopy) was carried out. The possibility of nanotubes functionalization by oxygen atoms of negative amino acid residues Asp and Glu, which are on the outer surface of BSA, is shown by molecular modeling. The formation of covalent bonds between BSA and SWCNT in nanocomposites with different concentrations of nanotubes (0.01, 0.1 and 1 g/l) was confirmed by vibrational spectra. The covalent interaction between BSA with SWCNT under the laser irradiation leads to the conformational changes in the secondary and tertiary structures of albumin. This is confirmed by a significant decrease in the intensity of the absorption bands in the high-frequency region. The calculation of the vibrational spectra of the three Glycine:Glycine, Glutamic acid:Threonine and Aspartic acid:Lysine complexes, which take into account hydrogen, ion-dipole and ion-ion bonds, showed that a disturbance in the intermolecular interaction between amino acid residues led to significant decrease in the intensity of absorption bands in the region of stretching vibrations bonds OH and NH. From the Raman spectra, it was found that a significant number of defects in SWCNT is caused by the covalent attachment of oxygen atoms to the graphene surface of nanotubes. An increase in the diameter of nanotubes (4 nm) has practically no effect on the absorption spectrum of nanocomposite, while measuring the concentration of SWCNT affects the FTIR spectra. This confirmed the hydrophobic interaction between BSA and SWCNT. Thus, it was shown that BSA solid nanocomposites with CNTs can interact either with the help of hydrophobic forces or with the formation of covalent bonds, which depends on the diameter of the used nanotubes. The viability of connective fibroblast tissue cells on nanocomposites with both types of SWCNT was demonstrated. It was found that nanocomposites based on SWCNT I provide slightly better compatibility of their structure with fibroblasts. It allows to achieve better cell adhesion to the nanocomposite surface. These criteria make extensive use of scaffold nanocomposites in biomedicine, depending on the requirements for their quality and application.