Selection of quorum quenching (QQ) bacteria for membrane biofouling control: effect of different Gram-staining QQ bacteria, Bacillus sp. T5 and Delftia sp. T6, on microbial population in membrane bioreactors.

This study aimed to address the gap in understanding how the microbial community present within quorum quenching-membrane bioreactor (QQ-MBRs) changes during the operations by investigating the behavior of two different types of QQ bacteria, Bacillus sp. T5 and Delftia sp. T6. The anti-biofouling effects of T5 and T6 in the QQ-MBR were 85% and 76%, respectively. According to the Illumina HiSeq results, when the QQ-MBR was operated with Gram-positive bacteria, T5, in the mixed liquor a reduction was observed in Gram-positive bacteria and Gram-negative bacteria population increased. In contrast, when the QQ-MBR was operated with Gram-negative bacteria, T6, Gram-negative bacteria population reduced and an increase in Gram-positive bacteria observed. As such, the outputs of the Illumina analysis revealed that use of Gram-negative QQ bacteria in the reactor induced a Gram-positive microbial community and vice versa. This indicates that a close interaction occurs between indigenous Gram-negative and positive bacterial phyla, and Bacillus sp. T5/Delftia sp. T6 is fundamental to the performance of MBRs. This is the first study demonstrating such a relationship and assistance selecting QQ bacteria/strategy in an effective way.

Evaluation of a novel anti-biofouling microorganism (Bacillus sp. T5) for control of membrane biofouling and its effect on bacterial community structure in membrane bioreactors.

The effects of a newly isolated quorum quenching (QQ) bacteria (Bacillus sp. T5) on the microbial community has been evaluated via the Illumina sequencing method. Membrane bioreactors (MBRs) operated with this novel QQ bacterium to evaluate the improvement in the performance of MBR. Anti-biofouling effect of T5 was enhanced as 71% compared to the control reactor. Also, QQ bacteria did not have any negative effect on the removal of organics during the process. Gram-negative bacteria were found to be dominant over Gram-positive bacteria. Proteobacteria, Actinobacteria, Bacteroidetes, Acidobacteria, Firmicutes, and Chloroflexi were dominant phyla in the control and QQ reactors. The proportion of Alphaproteobacteria was most significant among Proteobacteria. The relative abundances of Actinobacteria, Acidobacteria, and Firmicutes were significantly affected by Quorum quenching mechanism. On the other hand, QQ activity of Bacillus sp. T5 significantly influenced the relative abundance of Proteobacteria, Bacteroidetes, and Chloroflexi. The QQ process appeared to generate variations in the structure of the microbial community. According to the results of the molecular analyses, the syntrophic interaction of Bacillus sp. T5 and indigenous Gram-negative and Gram-positive bacterial community is critical to the performance of MBRs.

Membrane properties and anti-bacterial/anti-biofouling activity of polysulfone-graphene oxide composite membranes phase inversed in graphene oxide non-solvent.

A new and facile method for the fabrication of polysulfone-graphene oxide composite membranes is reported, where after casting, phase inversion is carried out with graphene oxide flakes (GO) in a coagulation bath. The membranes were characterized and the morphology was analysed using scanning electron microscopy. A bacterial inhibition ratio of 74.5% was observed with membranes fabricated from a very low concentration of di-water-GO non-solvent (0.048% of GO). The membranes were successfully tested for permeate flux and fouling resistance using activated sludge filtration from an MBR system. The observed trend shows that GO can operate as a protective barrier for membrane pores against the bacterial community. To our knowledge this is the first time where the immersion precipitation mechanism was carried out in a coagulation bath with GO flakes under continuous stirring. Using this method, a very low concentration of GO is required to fabricate membranes with conventional GO composite membrane properties and better selectivity.

Immobilization of Acidithiobacillus ferrooxidans on sulfonated microporous poly(styrene-divinylbenzene) copolymer with granulated activated carbon and its use in bio-oxidation of ferrous iron.

The immobilization efficiencies of Acidithiobacillus ferrooxidans cells on different immobilization matrices were investigated for biooxidation of ferrous iron (Fe(2+)) to ferric iron (Fe(3+)). Six different matrices were used such as the polyurethane foam (PUF), granular activated carbon (GAC), raw poly(styrene-divinylbenzene) copolymer (rawSDVB), raw poly(styrene-divinylbenzene) copolymer with granular activated carbon (rawSDVB-GAC), sulfonated poly(styrene-divinylbenzene) copolymer (sulfSDVB) and sulfonated poly(styrene-divinylbenzene) copolymer with granular activated carbon (sulfSDVB-GAC). The sulfSDVB-GAC polymer showed the best performance for Fe(2+) biooxidation. It was used at packed-bed bioreactor and the kinetic parameters were obtained. The highest Fe(2+) biooxidation rate (R) was found to be 4.02 g/L h at the true dilution rate (Dt) of 2.47 1/h and hydraulic retention time (τ) of 0.4 h. The sulfSDVB-GAC polymer was used for the first time as immobilization material for A. ferrooxidans for Fe(2+) biooxidation.

Influence of membrane fouling reducers (MFRs) on filterability of disperse mixed liquor of jet loop bioreactors.

The effects of membrane fouling reducers (MFRs) (the cationic polyelectrolyte (CPE) and FeCI(3)) on membrane fouling were studied in a lab-scale jet loop submerged membrane bioreactor (JL-SMBR) system. The optimum dosages of MFRs (CPE dosage=20 mg g(-1)MLSS, FeCI(3) dosage=14 mg g(-1)MLSS) were continuously fed to JL-SMBR system. The soluble and bound EPS concentrations as well as MLSS concentration in the mixed liquor of JL-SMBR were not changed substantially by the addition of MFRs. However, significant differences were observed in particle size and relative hydrophobicity. Filtration tests were performed by using different membrane types (polycarbonate (PC) and nitrocellulose mixed ester (ME)) and various pore sizes (0.45-0.22-0.1 µm). The steady state fluxes (J(ss)) of membranes increased at all membranes after MFRs addition to JL-SMBR. The filtration results showed that MFRs addition was an effective approach in terms of improvement in filtration performance for both membrane types.