Life Cycle Assessment of Rare Earth Elements-Free Permanent Magnet Alternatives: Sintered Ferrite and Mn-Al-C.

Permanent magnets are fundamental constituents in key sectors such as energy and transport, but also robotics, automatization, medicine, etc. High-performance magnets are based on rare earth elements (RE), included in the European list of critical raw materials list. The volatility of their market increased the research over the past decade to develop RE-free magnets to fill the large performance/cost gap existing between ferrites and RE-based magnets. The improvement of hard ferrites and Mn-Al-C permanent magnets plays into this important technological role in the near future. The possible substitution advantage was widely discussed in the literature considering both magnetic properties and economic aspects. To evaluate further sustainability aspects, the present paper gives a life cycle assessment quantifying the environmental gain resulting from the production of RE-free magnets based on traditional hexaferrite and Mn-Al-C. The analysis quantified an advantage of both magnets that overcomes the 95% in all the considered impact categories (such as climate change, ozone depletion, human toxicity) compared to RE-based technologies. The benefit also includes the health and safety of working time aspects, proving possible reduction of worker risks by 3-12 times. The results represent the fundamentals for the development of green magnets that are able to significantly contribute to an effective sustainable transition.

A review of the existing and emerging technologies for wastewaters containing tetramethyl ammonium hydroxide (TMAH) and waste management systems in micro-chip microelectronic industries.

The present work aims to describe and review the available technologies and the recent advancements in treating industrial wastewater containing tetramethylammonium hydroxide (TMAH). It is a quaternary ammonium salt and widely used in the microelectronics industry; this kind of company produces large quantities of wastewater containing TMAH. The exhausted solutions must be treated appropriately since TMAH is corrosive, toxic to human health, and ecotoxic. Regarding the concentration at discharge, currently there are no European regulations. Still, it has been indicated that the substance has a negative influence on the oxygen balance and cause eutrophication, and fall into the relevant categories. In the first part of the work, the available technologies and the recent advancements for the treatment of TMAH contained in industrial wastewater are reviewed. Separation methods as such adsorption, ion exchange, membrane processes, and destruction technologies classified as advanced oxidation processes and biological processes have been considered. In the second part of the manuscript, industrial patented wastewater treatments have been described. Biological processes are those more used, being more economically feasible, require very long times not always sustainable.

Technical feasibility of biodiesel production from virgin oil and waste cooking oil: Comparison between traditional and innovative process based on hydrodynamic cavitation.

Biodiesel production calls for innovative solutions to turn into a competitive process with a reduced environmental impact. One of the process bottlenecks stands in the immiscibility of oil and alcohol as raw materials, so mixing process largely impacts the overall process cost. This process step, if carried out by using hydrodynamic cavitation, has the possibility to become a benchmark for large scale applications. In this paper a process analysis of biodiesel production scheme is developed starting from two different feedstocks, virgin oil and waste cooking oil. At the first the traditional process scheme has been simulated, in a second simulation, the reactor for the biodiesel production is interchanged with a hydrodynamic cavitation reactor. In the paper, the comparison between the traditional and innovative process by using life cycle costing approach has been presented, thus providing indications for industrial technological implementation coming from a professional tool for process analysis. It is worth noting that the introduction of hydrodynamic cavitation reduces of about 40% the energy consumption with respect to the traditional process. As regards the total treatment costs, when using virgin oil as feedstock, they were in the range 820-830 €/t (innovative and traditional process, respectively); while starting from waste cooking oil the costs decreased of about 60%, down to 290-300 €/t (innovative and traditional process, respectively).

Purification of residual leach liquors from hydrometallurgical process of NiMH spent batteries through micellar enhanced ultra filtration.

Hydrometallurgical processes for the treatment and recovery of metals from waste electrical and electronic equipment produce wastewaters containing heavy metals. These residual solutions cannot be discharged into the sewer without an appropriate treatment. Specific wastewater treatments integrated with the hydrometallurgical processes ensure a sustainable recycling loops of the electrical wastes to maximize the metals recovery and minimize the amount of wastes and wastewaters produced. In this research activity the efficiency of ultrafiltration combined with surfactant micelles (micellar-enhanced ultrafiltration) was tested to remove metals form leach liquors obtained after leaching of NiMH spent batteries. In the micellar-enhanced ultrafiltration, a surfactant is added into the aqueous stream containing contaminants or solute above its critical micelle concentration. When the surfactant concentration exceeding this critical value, the surfactant monomers will assemble and aggregate to form micelles having diameter larger than the pore diameter of ultrafiltration membrane. Micelles containing contaminants whose diameter is larger than membrane pore size will be rejected during ultrafiltration process, leaving only water, unsolubilized contaminants and surfactant monomers in permeate stream. The experiments are carried out in a lab-scale plant, where a tubular ceramic ultrafiltration membrane is used with adding a surfactant to concentrate heavy metals in the retentate stream, producing a permeate of purified water that can be reused inside the process, thus minimizing the fresh water consumption.

Treatment of WEEE industrial wastewaters: Removal of yttrium and zinc by means of micellar enhanced ultra filtration.

In this paper, the efficiency of micellar enhanced ultrafiltration technique (MEUF) was tested for the removal of yttrium and zinc ions from synthetic industrial liquid wastes. UF membranes (monotubular ceramic membranes of 210 kDa and 1 kDa molecular weight cut-off) were used with adding an anionic surfactant, sodium dodecyl sulfate (SDS). A two - level full factorial design was performed in order to evaluate the effect of molecular weight cut-off, sodium dodecyl sulfate concentration and pressure on the permeate flux and rejection yields. It was found that the single factors presented the largest influence on the permeate flux: the membrane pore size and the pressure had positive effect, instead the SDS had negative effect. Regarding the metal rejection yields the main relevant factors were the membrane pore size with a negative effect, followed by the surfactant concentration with a positive effect. The effect of the pressure seemed to be almost negligible, for zinc removal experiments had a positive effect in the interactions with the surfactant and membrane pore size. The results showed that very good removal percentages up to 99% were achieved for both metals under the following conditions: 1 kDa membrane MWCO, in the presence of the surfactant at a concentration above CMC independently of the investigated pressure.

A hydrometallurgical process for the recovery of terbium from fluorescent lamps: Experimental design, optimization of acid leaching process and process analysis.

Terbium and rare earths recovery from fluorescent powders of exhausted lamps by acid leaching with hydrochloric acid was the objective of this study. In order to investigate the factors affecting leaching a series of experiments was performed in according to a full factorial plan with four variables and two levels (42). The factors studied were temperature, concentration of acid, pulp density and leaching time. Experimental conditions of terbium dissolution were optimized by statistical analysis. The results showed that temperature and pulp density were significant with a positive and negative effect, respectively. The empirical mathematical model deducted by experimental data demonstrated that terbium content was completely dissolved under the following conditions: 90 °C, 2 M hydrochloric acid and 5% of pulp density; while when the pulp density was 15% an extraction of 83% could be obtained at 90 °C and 5 M hydrochloric acid. Finally a flow sheet for the recovery of rare earth elements was proposed. The process was tested and simulated by commercial software for the chemical processes. The mass balance of the process was calculated: from 1 ton of initial powder it was possible to obtain around 160 kg of a concentrate of rare earths having a purity of 99%. The main rare earths elements in the final product was yttrium oxide (86.43%) following by cerium oxide (4.11%), lanthanum oxide (3.18%), europium oxide (3.08%) and terbium oxide (2.20%). The estimated total recovery of the rare earths elements was around 70% for yttrium and europium and 80% for the other rare earths.

Yttrium recovery from primary and secondary sources: a review of main hydrometallurgical processes.

Yttrium is important rare earths (REs) used in numerous fields, mainly in the phosphor powders for low-energy lighting. The uses of these elements, especially for high-tech products are increased in recent years and combined with the scarcity of the resources and the environmental impact of the technologies to extract them from ores make the recycling waste, that contain Y and other RE, a priority. The present review summarized the main hydrometallurgical technologies to extract Y from ores, contaminated solutions, WEEE and generic wastes. Before to discuss the works about the treatment of wastes, the processes to retrieval Y from ores are discussed, since the processes are similar and derived from those already developed for the extraction from primary sources. Particular attention was given to the recovery of Y from WEEE because the recycle of them is important not only for economical point of view, considering its value, but also for environmental impact that this could be generated if not properly disposal.

Recovery of yttrium from fluorescent powder of cathode ray tube, CRT: Zn removal by sulphide precipitation.

This work is focused on the recovery of yttrium and zinc from fluorescent powder of cathode ray tube (CRT). Metals are extracted by sulphuric acid in the presence of hydrogen peroxide. Leaching tests are carried out according to a 2(2) full factorial plan and the highest extraction yields for yttrium and zinc equal to 100% are observed under the following conditions: 3M of sulphuric acid, 10% v/v of H2O2 concentrated solution at 30% v/v, 10% w/w pulp density, 70°C and 3h of reaction. Two series of precipitation tests for zinc are carried out: a 2(2) full factorial design and a completely randomized factorial design. In these series the factors investigated are pH of solution during the precipitation and the amount of sodium sulphide added to precipitate zinc sulphide. The data of these tests are used to describe two empirical mathematical models for zinc and yttrium precipitation yields by regression analysis. The highest precipitation yields for zinc are obtained under the following conditions: pH equal to 2-2.5% and 10-12%v/v of Na2S concentrated solution at 10%w/v. In these conditions the coprecipitation of yttrium is of 15-20%. Finally further yttrium precipitation experiments by oxalic acid on the residual solutions, after removing of zinc, show that yttrium could be recovered and calcined to obtain the final product as yttrium oxide. The achieved results allow to propose a CRT recycling process based on leaching of fluorescent powder from cathode ray tube and recovery of yttrium oxide after removing of zinc by precipitation. The final recovery of yttrium is 75-80%.