Optimization of a Mucoadhesive Vaginal Gel Containing Clotrimazole Using a D-Optimal Experimental Design and Multivariate Analysis.

The aim of this study was to develop a suitable clotrimazole (CLT)-loaded mucoadhesive vaginal gel (CLT-MVG) for topical applications in vaginal candidiasis. Ten CLT-MVG formulations were prepared, consisting of mixtures of acid polyacrylic (Carbopol 940) and polyethene oxides, Sentry Polyox WSRN 1105 or 750, according to an experimental D-optimal design, and CLT was suspended at a ratio of 1%. The prepared CLT-MVG formulations were studied in vitro, and the formulation containing Carbopol 940 0.89% combined with PEO 1105 1.39% was identified with the optimal rheological and in vitro bioadhesion properties, ensuring the prolonged release of CLT, with a similarity factor greater than 50, indicating dissolution profile similarity for three batches of the optimized formulation. This optimized formulation showed a pH in the tolerance range, and an adequate ex vivo mucoadhesion time, while the FT-IR studies revealed no interactions between the excipients and CLT. The microscopic analysis identified a mean particle size of suspended CLT of 5.24 ± 0.57 µm. The in vitro antifungal activity of the optimized formulation was tested on twenty strains of Candida albicans and proved to be better compared to a marketed clotrimazole preparation, showing a greater inhibition effect (p < 0.05). The optimized formulation could be a good candidate for the local treatment of vaginal mycosis.

Formulation, preparation and in vitro - in vivo evaluation of compression-coated tablets for the colonic-specific release of ketoprofen

ABSTRACT The aim of this study was to formulate and prepare compression-coated tablets for colonic release (CR-tablets), and to evaluate the bioavailability of ketoprofen following the administration of a single dose from mini-tablets with immediate release (IR-tablets) compared to CR-tablets. CR-tablets were prepared based on time-controlled hydroxypropylmethylcellulose K100M inner compression-coating and pH-sensitive Eudragit® L 30D-55 outer film-coating. The clinical bioavailability study consisted of two periods, in which two formulations were administered to 6 volunteers, according to a randomized cross-over design. The apparent cumulative absorption amount of ketoprofen was estimated by plasma profile deconvolution. CR-tablets were able to delay ketoprofen's release. Compared to IR-tablets used as reference, for the CR-tablets the maximum plasma concentration (Cmax) was lower (4920.33±1626.71 ng/mL vs. 9549.50±2156.12 ng/mL for IR-tablets) and the time needed to reach Cmax (tmax) was 5.33±1.63 h for CR-tablets vs. 1.33±0.88 h for IR-tablets. In vitro-in vivo comparison of the apparent cumulative absorption amount of ketoprofen showed similar values for the two formulations. Therefore, the obtained pharmacokinetic parameters and the in vitro-in vivo comparison demonstrated the reliability of the developed pharmaceutical system and the fact that it is able to avoid the release of ketoprofen in the first part of the digestive tract.

Development of a reservoir type prolonged release system with felodipine via simplex methodology.

BACKGROUND AND AIMS: Felodipine is a dihydropyridine calcium antagonist that presents good characteristics to be formulated as prolonged release preparations. The aim of the study was the formulation and in vitro characterization of a reservoir type prolonged release system with felodipine, over a 12 hours period using the Simplex method. METHODS: The first step of the Simplex method was to study the influence of the granules coating method on the felodipine release. Furthermore the influence of the coating polymer type, the percent of the coating polymer and the percent of pore forming agent in the coating on the felodipine release were studied. Afterwards these two steps of the experimental design the percent of Surelease applied on the felodipine loaded granules and the percent of pore former in the polymeric coating formulation variables were studied. The in vitro dissolution of model drug was performed in phosphate buffer solution (pH 6.5) with 1% sodium lauryl sulfate. The released drug quantification was done using an HPLC method. The release kinetics of felodipine from the final granules was assessed using different mathematical models. RESULTS: A 12 hours release was achieved using granules with the size between 315-500 µm coated with 45% Surelease with different pore former ratios in the coating via the top-spray method. CONCLUSION: We have prepared prolonged release coated granules with felodipine using a fluid bed system based on the Simplex method. The API from the studied final formulations was released over a 12 hours period and the release kinetics of the model drug substance from the optimized preparations fitted best the Higuchi and Peppas kinetic models.