Laser-cutting: A novel alternative approach for point-of-care manufacturing of bespoke tablets.

A novel subtractive manufacturing method to produce bespoke tablets with immediate and extended drug release is presented. This is the first report on applying fusion laser cutting to produce bespoke furosemide solid dosage forms based on pharmaceutical-grade polymeric carriers. Cylindric tablets of different sizes were produced by controlling the two-dimensional design of circles of the corresponding diameter. Immediate and extended drug release patterns were achieved by modifying the composition of the polymeric matrix. Thermal analysis and XRD indicated that furosemide was present in an amorphous form. The laser-cut tablets demonstrated no significant drug degradation (<2%) nor the formation of impurities were identified. Multi-linear regression was used to quantify the influences of laser-cutting process parameters (laser energy levels, scan speeds, and the number of laser applications) on the depth of the laser cut. The utility of this approach was exemplified by manufacturing tablets of accurate doses of furosemide. Unlike additive or formative manufacturing, the reported approach of subtractive manufacturing avoids the modification of the structure, e.g., the physical form of the drug or matrix density of the tablet during the production process. Hence, fusion laser cutting is less likely to modify critical quality attributes such as release patterns or drug contents. In a point-of-care manufacturing scenario, laser cutting offers a significant advantage of simplifying quality control and a real-time release of laser-cut products such as solid dosage forms and implants.

Towards point-of-care manufacturing and analysis of immediate-release 3D printed hydrocortisone tablets for the treatment of congenital adrenal hyperplasia.

Hydrocortisone (HC) is the preferred drug in children with congenital adrenal hyperplasia due to its lower potency as well as fewer reports of side effects. Fused deposition modelling (FDM) 3D printing holds the potential to produce low-cost personalised doses for children at the point of care. However, the compatibility of the thermal process to produce immediate-release bespoke tablets for this thermally labile active is yet to be established. This work aims to develop immediate-release HC tablets using FDM 3D printing and assess drug contents as a critical quality attribute (CQA) using a compact, low-cost near-infrared (NIR) spectroscopy as a process analytical technology (PAT). The FDM 3D printing temperature (140 °C) and drug concentration in the filament (10%-15% w/w) were critical parameters to meet the compendial criteria for drug contents and impurities. Using a compact low-cost NIR spectral device over a wavelength of 900-1700 nm, the drug contents of 3D printed tablets were assessed. Partial least squares (PLS) regression was used to develop individual calibration models to detect HC content in 3D printed tablets of lower drug contents, small caplet design, and relatively complex formula. The models demonstrated the ability to predict HC concentrations over a wide concentration range (0-15% w/w), which was confirmed by HPLC as a reference method. Ultimately, the capability of the NIR model had preceding dose verification performance on HC tablets, with linearity (R2 = 0.981) and accuracy (RMSECV = 0.46%). In the future, the integration of 3DP technology with non-destructive PAT techniques will accelerate the adoption of on-demand, individualised dosing in a clinical setting.

The use of near-infrared as process analytical technology (PAT) during 3D printing tablets at the point-of-care.

Fused deposition modelling (FDM) is one of the most researched 3D printing technologies that holds great potential for low-cost manufacturing of personalised medicine. To achieve real-time release, timely quality control is a major challenge for applying 3D printing technologies as a point-of-care (PoC) manufacturing approach. This work proposes the use of a low-cost and compact near-infrared (NIR) spectroscopy modality as a process analytical technology (PAT) to monitor a critical quality attribute (drug content) during and after FDM 3D printing process. 3D printed caffeine tablets were used to manifest the feasibility of the NIR model as a quantitative analytical procedure and dose verification method. Caffeine tablets (0-40 % w/w) were fabricated using polyvinyl alcohol and FDM 3D printing. The predictive performance of the NIR model was demonstrated in linearity (correlation coefficient, R2) and accuracy (root mean square error of prediction, RMSEP). The actual drug content values were determined using the reference high-performance liquid chromatography (HPLC) method. The model of full-completion caffeine tablets demonstrated linearity (R2 = 0.985) and accuracy (RMSEP = 1.4 %), indicated to be an alternative dose quantitation method for 3D printed products. The ability of the models to assess caffeine contents during the 3D printing process could not be accurately achieved using the model built with complete tablets. Instead, by building a predictive model for each completion stage of 20 %, 40 %, 60 % and 80 %, the model of different completion caffeine tablets displayed linearity (R2 of 0.991, 0.99, 0.987, and 0.983) and accuracy (RMSEP of 2.22 %, 1.65 %, 1.41 %, 0.83 %), respectively. Overall, this study demonstrated the feasibility of a low-cost NIR model as a non-destructive, compact, and rapid analysis dose verification method enabling the real-time release to facilitate 3D printing medicine production in the clinic.

Creating Acceptable Tablets 3D (CAT 3D): A Feasibility Study to Evaluate the Acceptability of 3D Printed Tablets in Children and Young People.

3D printing (3DP) has been proposed as a novel approach for personalising dosage forms for children and young people (CYP). Owing to its low cost and the lack of need for finishing steps, fused deposing modelling (FDM) 3DP has been heavily researched in solid dosage forms (SDFs) manufacturing. However, the swallowability and overall acceptability of 3D printed dosage forms are yet to be established. This work is the first to evaluate the acceptability of different sized 3D printed placebo SDFs in CYP (aged 4-12 years). All participants had previously participated in a feasibility study (CAT study) that assessed the swallowability and acceptability of different sized GMP manufactured placebo conventional film-coated tablets, and therefore only attempted to swallow one 3D printed tablet. The participants assessed the swallowability, acceptability, mouthfeel, volume of water consumed, and taste of the sample using a 5-point hedonic facial scale on a participant questionnaire. A total of 30 participants were recruited, 87% of whom successfully swallowed the 3D printed tablet that they attempted to take. Attributes of the 3D printed tablets were scored as acceptable by the following percentage of participants-swallowability (80%), mouthfeel/texture (87%), the volume of water consumed (80%), taste (93%), and overall acceptability (83%). Overall, 77% of children reported they would be happy to take the tablet every day if it was a medicine. Participants were also asked which tablets felt better in the mouth-the film-coated tablets or the 3D printed tablets, and the most popular response (43%) was that both were acceptable. This study shows that FDM-based 3D printed SDFs may be a suitable dosage form for children aged 4-12 years. The results from this feasibility study will be used to inform a larger, definitive study looking at the acceptability of 3D printed tablets in children.

A Novel Multilayer Natural Coating for Fed-State Gastric Protection.

Several nutraceutical products require gastric protection against the hostile environment in the stomach. Currently marketed synthetic and semi-synthetic coatings suffer from major shortcomings such as poor gastric protection, slow-release response to pH change, and the use of artificial ingredients. The challenge of coating natural products is further exacerbated by the relatively high gastric pH in the fed state. In this work, a novel natural enteric coating is presented as a breakthrough alternative to current solutions. Two coating systems were devised: (i) a triple-layer coating that comprises a wax layer embedded between two alginate-based coatings, and (ii) a double-layer coating, where an overcoat of organic acids (fumaric or citric acid) is applied to an alginate-based coating. The multi-layer architecture did not impact the pH-responsive nature of the coating even when more biologically relevant Krebs bicarbonate buffer of lower buffer capacity was used. Interestingly, the gastric protection barrier of organic acid-based coating remained resistant at elevated gastric pH 2, 3, or 4 for 2 h. This is the first report of using an alginate-based coating to provide gastric protection against fed-state stomach conditions (pH 2-4). Being biodegradable, naturally occurring, and with no limit on daily intake, the reported novel coating provides a superior platform to current coating solutions for pharmaceutical and nutraceutical products.

Impact of nanosizing on the formation and characteristics of polymethacrylate films: micro- versus nano-suspensions.

Aqueous-based film coating suspensions are associated with reliance on alkalinising reagents and poor film formation. The impact of particle size in this process and resultant film properties remains unclear. This study offers the first direct comparison of film formation properties between aqueous micro- and nano-suspensions of the enteric polymer Eudragit S100. High-pressure homogenisation was employed to produce nano-suspensions of the enteric polymer. Formed enteric suspensions (micro- and nano-) were evaluated in terms of size, morphology, and ability to form film; with resultant films analysed in terms of; film thickness, mechanical and thermoplastic properties, water uptake, weight loss, and drug permeability in acidic medium. High-pressure homogenisation yielded particles within a submicron range (150-200 nm). Produced nano-suspensions formed significantly thinner films (p < 0.01), at lower plasticiser concentrations, than films cast from micro-suspensions (differences in thickness up to 100 µm); however, exhibited comparative gastro-resistant properties (p > 0.05) in terms of water uptake (∼25% w/w), weight loss (<16% w/w) and drug permeability (<0.1%). Interestingly, nano-suspension-based films exhibited lower glass transition temperatures (Tg) (p < 0.01), when compared to films cast from micro-suspensions (∼7-20 °C difference), indicating enhanced plasticisation. This was reflected in film mechanical properties; where nano-suspension-based films demonstrated significantly lower tensile strength (p < 0.01) and higher percentage elongation (p < 0.05), suggesting high elasticity. Thinner, highly elastic films were formed from nano-suspensions, compared to films cast from micro-suspensions, exhibiting comparative properties; obviating the need for alkalinising agents and high concentrations of plasticiser.

Can filaments be stored as a shelf-item for on-demand manufacturing of oral 3D printed tablets? An initial stability assessment.

3D printing of oral solid dosage forms is a recently introduced approach for dose personalisation. Fused deposition modelling (FDM) is one of the promising and heavily researched 3D printing techniques in the pharmaceutical field. However, the successful application of this technique relies greatly on the mass manufacturing of physically and chemically stable filaments, that can be readily available as a shelf item to be 3D printed on-demand. In this work, the stability of methacrylate polymers (Eudragit EPO, RL, L100-55 and S100), hydroxypropyl cellulose (HPC SSL) and polyvinyl pyrrolidone (PVP)-based filaments over 6 months were investigated. Filaments manufactured by hot melt extrusion (HME) were stored at either 5 °C or 30 °C + 65 %RH with/without vacuuming. The effects of storage on their dimensions, visual appearance, thermal properties, and 'printability' were analysed. Theophylline content, as well as in vitro release from the 3D printed tablets were also investigated. The filaments were analysed before storage, then after 1, 3 and 6 months from the manufacturing date. Storing the filaments at these conditions had a significant effect on their physical properties, such as shape, dimensions, flexibility and hence compatibility with FDM 3D printing. In general, the methacrylate-based filaments were more physically stable and compatible with FDM 3D printing following storage. Owing to their hygroscopic nature, cellulose- and PVP-based filaments demonstrated a reduction in their glass transition temperature upon storage, leading to increased flexibility and incompatibility with FDM 3D printer. Theophylline contents was not significantly changed during the storage. This work provides preliminary data for the impact of polymer species on the long-term stability of filaments. In general, storage and packaging conditions have a major impact on the potential of on-demand manufacturing of 3D printed tablets using hot melt extruded filaments.

Solvent-free temperature-facilitated direct extrusion 3D printing for pharmaceuticals.

In an era moving towards digital health, 3D printing has successfully proven its applicability in providing personalised medicine through a technology-based approach. Among the different 3D printing techniques, direct extrusion 3D printing has been demonstrated as a promising approach for on demand manufacturing of solid dosage forms. However, it usually requires the use of elevated temperatures and/or the incorporation of an evaporable solvent (usually water). This can implicate the addition of a drying step, which may compromise the integrity of moisture- or temperature-sensitive drugs, and open the door for additional quality control challenges. Here, we demonstrate a new approach that simplifies direct extrusion 3D printing process with the elimination of the post-printing drying step, by merely adding a fatty glyceride, glyceryl monostearate (GMS), to a model drug (theophylline) and permeable water insoluble methacrylate polymers (Eudragit RL and RS). Indeed, rheological studies indicated that the addition of a combination of a plasticiser, (triethyl citrate), and GMS to theophylline: methacrylate polymer blends significantly reduced the extensional viscosity (to <2.5 kPa·Sec) at 90 °C. Interestingly, GMS demonstrated a dual temperature-dependant behaviour by acting both as a plasticiser and a lubricant at printing temperature (90-110 °C), while aiding solidification at room temperature. X-ray powder diffraction indicated incomplete miscibility of GMS within the polymeric matrix at room temperature with the presence of a subtle diffraction peak, at 2(Θ) = 20°. The 3D printed tablets showed acceptable compendial weight and content uniformity as well as sufficient mechanical resistance. In vitro theophylline release from 3D printed tablets was dependant on Eudragit RL:RS ratio. All in all, this work contributes to the efforts of developing a simplified, facile and low-cost 3D printing for small batch manufacturing of bespoke tablets that circumvents the use of high temperature and post-manufacturing drying step.

An innovative wax-based enteric coating for pharmaceutical and nutraceutical oral products.

In this work, a novel enteric coating based on natural waxes and alginate was reported. Initially, theophylline tablets were coated with emulsified ceresin wax in heated aqueous alginate solution using a fluidised bed coating technology. A coating level of 10% proved sufficient to prevent tablets from uptaking gastric medium (<5%) and produced a delayed release profile that complies to the pharmacopeial criteria of enteric coating release. Then, a wide range of emulsions based on other natural waxes (white beeswax, yellow beeswax, cetyl palmitate, carnauba wax or rice bran wax) yielded coatings with similar disintegration times and release profiles. Interestingly, the ceresin-based coating showed a superior performance at inhibiting acid uptake and enabling highly pH-responsive drug release in comparison to different commercially available GRAS enteric coating products (Eudraguard® Control, Swanlac® ASL10, and Aquateric™ N100). The coating was stable for 6 months at 30 °C and 65% RH. This innovative approach of applying hot O/W emulsion of natural waxes yielded an aesthetically attractive and stable coating with gastric protection and pH-sensitive release properties. The novel coating can be an efficient and promising alternative to overcome the shortcomings of current GRAS grade enteric coating products.

A Facile and Novel Approach to Manufacture Paclitaxel-Loaded Proliposome Tablet Formulations of Micro or Nano Vesicles for Nebulization.

PURPOSE: The aim of this study was to develop novel paclitaxel-loaded proliposome tablet formulations for pulmonary drug delivery. METHOD: Proliposome powder formulations (i.e. F1 - F27) were prepared employing Lactose monohydrate (LMH), Microcrystalline cellulose (MCC) or Starch as a carbohydrate carriers and Soya phosphatidylcholine (SPC), Hydrogenated soya phosphatidylcholine (HSPC) or Dimyristoly phosphatidylcholine (DMPC) as a phospholipid. Proliposome powder formulations were prepared in 1:5, 1:15 or 1:25 w/w lipid phase to carrier ratio (lipid phase; comprising of phospholipid and cholesterol in 1:1 M ratio) and Paclitaxel (PTX) was used as model anticancer drug. RESULTS: Based on flowability studies, out of 27 formulations; F3, F6, and F9 formulations were selected as they exhibited an excellent angle of repose (AOR) (17.24 ± 0.43, 16.41 ± 0.52 and 15.16 ± 0.72°), comparatively lower size of vesicles (i.e. 5.35 ± 0.76, 6.27 ± 0.59 and 5.43 ± 0.68 µm) and good compressibility index (14.81 ± 0.36, 15.01 ± 0.35 and 14.56 ± 0.14) via Carr's index. The selected formulations were reduced into Nano (N) vesicles via probe sonication, followed by spray drying (SD) to get a dry powder of these formulations as F3SDN, F6SDN and F9SDN, and gave high yield (>53%) and exhibited poor to very poor compressibility index values via Carr's Index. Post tablet manufacturing, F3 tablets formulation showed uniform weight uniformity (129.40 ± 3.85 mg), good crushing strength (14.08 ± 1.95 N), precise tablet thickness (2.33 ± 0.51 mm) and a short disintegration time of 14.35 ± 0.56 min, passing all quality control tests in accordance with British Pharmacopeia (BP). Upon nebulization of F3 tablets formulation, Ultrasonic nebulizer showed better nebulization time (8.75 ± 0.86 min) and high output rate (421.06 ± 7.19 mg/min) when compared to Vibrating mesh nebulizer. PTX-loaded F3 tablet formulations were identified as toxic (60% cell viability) to cancer MRC-5 SV2 cell lines while safe to normal MRC-5 cell lines. CONCLUSION: Overall, in this study LMH was identified as a superior carbohydrate carrier for proliposome tablet manufacturing in a 1:25 w/w lipid to carrier ratio for in-vitro nebulization via Ultrasonic nebulizer.

Additive Manufacturing of a Point-of-Care "Polypill:" Fabrication of Concept Capsules of Complex Geometry with Bespoke Release against Cardiovascular Disease.

Polypharmacy is often needed for the management of cardiovascular diseases and is associated with poor adherence to treatment. Hence, highly flexible and adaptable systems are in high demand to accommodate complex therapeutic regimens. A novel design approach is employed to fabricate highly modular 3D printed "polypill" capsules with bespoke release patterns for multiple drugs. Complex structures are devised using combined fused deposition modeling 3D printing aligned with hot-filling syringes. Two unibody highly modular capsule skeletons with four separate compartments are devised: i) concentric format: two external compartments for early release while two inner compartments for delayed release, or ii) parallel format: where nondissolving capsule shells with free-pass corridors and dissolution rate-limiting pores are used to achieve immediate and extended drug releases, respectively. Controlling drug release is achieved through digital manipulation of shell thickness in the concentric format or the size of the rate limiting pores in the parallel format. Target drug release profiles are achieved with variable orders and configurations, hence confirming the modular nature with capacity to accommodate therapeutics of different properties. Projection of the pharmacokinetic profile of this digital system capsules reveal how the developed approach can be applied in dose individualization and achieving multiple desired pharmacokinetic profiles.

Temperature and solvent facilitated extrusion based 3D printing for pharmaceuticals.

On demand manufacturing of patient-specific oral doses provides significant advantages to patients and healthcare staff. Several 3D printing (3DP) technologies have been proposed as a potential digital alternative to conventional manufacturing of oral tablets. For an additive manufacturing approach to be successful for on-demand preparation, a facile process with minimal preparation steps and training requirements is needed. A novel hybrid approach to the 3D printing process is demonstrated here based on combining both a solvent and heating to facilitate extrusion. The system employed a moderate elevated temperature range (65-100 °C), a brief drying period, and a simple set-up. In this approach, a compact material cylinder is used as a pharmaceutical ink to be extruded in a temperature-controlled metal syringe. The process proved compatible with hygroscopic polymers [Poly(vinyl alcohol (PVA) and polyvinylpyrrolidone (PVP)] and a number of pharmaceutical fillers (lactose, sorbitol and D-mannitol). The fabricated tablets demonstrated acceptable compendial weight and content uniformity as well as mechanical resistance. In vitro drug release of theophylline from 3D printed tablets was dependent on the nature of the polymer and its molecular weight. This reported approach offers significant advantages compared to other 3DP technologies: simplification of pre-product, the use of a moderate temperature range, a minimal drying period, and avoiding the use of mechanically complicated machinery. In the future, we envisage the use of this low-cost and facile approach to fabricate small batches of bespoke tablets.

Embedded 3D Printing of Novel Bespoke Soft Dosage Form Concept for Pediatrics.

Embedded three-dimensional printing (e-3DP) is an emerging method for additive manufacturing where semi-solid materials are extruded within a solidifying liquid matrix. Here, we present the first example of employing e-3DP in the pharmaceutical field and demonstrate the fabrication of bespoke chewable dosage forms with dual drug loading for potential use in pediatrics. LegoTM-like chewable bricks made of edible soft material (gelatin-based matrix) were produced by directly extruding novel printing patterns of model drug ink (embedded phase) into a liquid gelatin-based matrix (embedding phase) at an elevated temperature (70 °C) to then solidify at room temperature. Dose titration of the two model drugs (paracetamol and ibuprofen) was possible by using specially designed printing patterns of the embedded phase to produce varying doses. A linearity [R2 = 0.9804 (paracetamol) and 0.9976 (ibuprofen)] was achieved between percentage of completion of printing patterns and achieved doses using a multi-step method. The impact of embedded phase rheological behavior, the printing speed and the needle size of the embedded phase were examined. Owning to their appearance, modular nature, ease of personalizing dose and geometry, and tailoring and potential inclusion of various materials, this new dosage form concept holds a substantial promise for novel dosage forms in pediatrics.

3D printed oral theophylline doses with innovative 'radiator-like' design: Impact of polyethylene oxide (PEO) molecular weight.

Despite the abundant use of polyethylene oxides (PEOs) and their integration as an excipient in numerous pharmaceutical products, there have been no previous reports of applying this important thermoplastic polymer species alone to fused deposition modelling (FDM) 3D printing. In this work, we have investigated the manufacture of oral doses via FDM 3D printing by employing PEOs as a backbone polymer in combination with polyethylene glycol (PEG). Blends of PEO (molecular weight 100 K, 200 K, 300 K, 600 K or 900 K) with PEG 6 K (plasticiser) and a model drug (theophylline) were hot-melt extruded. The resultant filaments were used as a feed for FDM 3D printer to fabricate oral dosage forms (ODFs) with innovative designs. ODFs were designed in a radiator-like geometry with connected paralleled plates and inter-plate spacing of either 0.5, 1, 1.5 or 2 mm. X-ray diffraction patterns of the filaments revealed the presence of two distinctive peaks at 2θ = 7° and 12°, which can be correlated to the diffraction pattern of theophylline crystals. Blends of PEO and PEG yielded filaments of variable mechanically resistance (maximum load at break of 357, 608, 649, 882, 781 N for filament produced with PEO 100 K, 200 K, 300 K, 600 K or 900 K, respectively). Filaments of PEO at a molecular weight of 200-600 K were compatible with FDM 3D printing process. Further increase in PEO molecular weight resulted in elevated shear viscosity (>104 Pa.S) at the printing temperature and hindered material flow during FDM 3D printing process. A minimal spacing (1 mm) between parallel plates of the radiator-like design deemed essential to boost drug release from the structure. This is the first report of utilising this widely used biodegradable polymer species (PEOs and PEG) in FDM 3D printing.

'Temporary Plasticiser': A novel solution to fabricate 3D printed patient-centred cardiovascular 'Polypill' architectures.

Hypertension and dyslipidaemia are modifiable risk factors associated with cardiovascular diseases (CVDs) and often require a complex therapeutic regimen. The administration of several medicines is commonly associated with poor levels of adherence among patients, to which World Health Organisation (WHO) proposed a fixed-dose combination unit (polypill) as a strategy to improve adherence. In this work, we demonstrate the fabrication of patient-specific polypills for the treatment of CVDs by fused deposition modelling (FDM) 3D printing and introduce a novel solution to meet critical quality attributes. The construction of poly(vinyl alcohol) (PVA)-based polypills containing four model drugs (lisinopril dihydrate, indapamide, rosuvastatin calcium and amlodipine besylate) was revealed for the first time. The impact of tablet architecture was explored using multi-layered and unimatrix structures. The novel approach of using distilled water as a 'temporary co-plasticiser' is reported and was found to significantly lower the extruding (90 °C) and 3D printing (150 °C) temperatures from 170 °C and 210 °C respectively, with consequent reduction in thermal stress to the chemicals. XRD indicated that lisinopril dihydrate and amlodipine besylate maintained their crystalline form while indapamide and rosuvastatin calcium were essentially in amorphous form in the PVA tablets. From the multilayer polypills, the release profile of each drug was dependent on its position in the multilayer. In addition to the multilayer architecture offering a higher flexibility in dose titration and a more adaptive solution to meet the expectations of patient-centred therapy, we identify that it also allows orchestrating the release of drugs of different physicochemical characteristics. Adopting such an approach opens up a pathway towards low-cost multidrug delivery systems such as tablets, stents or implants for wider range of globally approved actives.

From 'fixed dose combinations' to 'a dynamic dose combiner': 3D printed bi-layer antihypertensive tablets.

There is an increased evidence for treating hypertension by a combination of two or more drugs. Increasing the number of daily intake of tablets has been reported to negatively affect the compliance of patients. Therefore, numerous fixed dose combinations (FDCs) have been introduced to the market. However, the inherent rigid nature of FDCs does not allow the titration of the dose of each single component for an individual patient's needs. In this work, flexible dose combinations of two anti-hypertensive drugs in a single bilayer tablet with a range of doses were fabricated using dual fused deposition modelling (FDM) 3D printer. Enalapril maleate (EM) and hydrochlorothiazide (HCT) loaded filaments were produced via hot-melt extrusion (HME). Computer software was utilised to design sets of oval bi-layer tablets of individualised doses. Thermal analysis and x-ray diffractometer (XRD) indicated that HCT remained crystalline in the polymeric matrix whilst EM appeared to be in an amorphous form. The interaction between anionic EM and cationic methacrylate polymer may have contributed to a drop in the glass transition temperature (Tg) of the filament and obviated the need for a plasticiser. Across all tablet sets, the methacrylate polymeric matrix provided immediate drug release profiles. This dynamic dosing system maintained the advantages of FDCs while providing a superior flexibility of dosing range, hence offering an optimal clinical solution to hypertension therapy in a patient-centric healthcare service.

Tablet fragmentation without a disintegrant: A novel design approach for accelerating disintegration and drug release from 3D printed cellulosic tablets.

Fused deposition modelling (FDM) 3D printing has shown the most immediate potential for on-demand dose personalisation to suit particular patient's needs. However, FDM 3D printing often involves employing a relatively large molecular weight thermoplastic polymer and results in extended release pattern. It is therefore essential to fast-track drug release from the 3D printed objects. This work employed an innovative design approach of tablets with unique built-in gaps (Gaplets) with the aim of accelerating drug release. The novel tablet design is composed of 9 repeating units (blocks) connected with 3 bridges to allow the generation of 8 gaps. The impact of size of the block, the number of bridges and the spacing between different blocks was investigated. Increasing the inter-block space reduced mechanical resistance of the unit, however, tablets continued to meet pharmacopeial standards for friability. Upon introduction into gastric medium, the 1 mm spaces gaplet broke into mini-structures within 4 min and met the USP criteria of immediate release products (86.7% drug release at 30 min). Real-time ultraviolet (UV) imaging indicated that the cellulosic matrix expanded due to swelling of hydroxypropyl cellulose (HPC) upon introduction to the dissolution medium. This was followed by a steady erosion of the polymeric matrix at a rate of 8 µm/min. The design approach was more efficient than a comparison conventional formulation approach of adding disintegrants to accelerate tablet disintegration and drug release. This work provides a novel example where computer-aided design was instrumental at modifying the performance of solid dosage forms. Such an example may serve as the foundation for a new generation of dosage forms with complicated geometric structures to achieve functionality that is usually achieved by a sophisticated formulation approach.

Fabricating a Shell-Core Delayed Release Tablet Using Dual FDM 3D Printing for Patient-Centred Therapy.

PURPOSE: Individualizing gastric-resistant tablets is associated with major challenges for clinical staff in hospitals and healthcare centres. This work aims to fabricate gastric-resistant 3D printed tablets using dual FDM 3D printing. METHODS: The gastric-resistant tablets were engineered by employing a range of shell-core designs using polyvinylpyrrolidone (PVP) and methacrylic acid co-polymer for core and shell structures respectively. Filaments for both core and shell were compounded using a twin-screw hot-melt extruder (HME). CAD software was utilized to design a capsule-shaped core with a complementary shell of increasing thicknesses (0.17, 0.35, 0.52, 0.70 or 0.87 mm). The physical form of the drug and its integrity following an FDM 3D printing were assessed using x-ray powder diffractometry (XRPD), thermal analysis and HPLC. RESULTS: A shell thickness ≥0.52 mm was deemed necessary in order to achieve sufficient core protection in the acid medium. The technology proved viable for incorporating different drug candidates; theophylline, budesonide and diclofenac sodium. XRPD indicated the presence of theophylline crystals whilst budesonide and diclofenac sodium remained amorphous in the PVP matrix of the filaments and 3D printed tablets. Fabricated tablets demonstrated gastric resistant properties and a pH responsive drug release pattern in both phosphate and bicarbonate buffers. CONCLUSIONS: Despite its relatively limited resolution, FDM 3D printing proved to be a suitable platform for a single-process fabrication of delayed release tablets. This work reveals the potential of dual FDM 3D printing as a unique platform for personalising delayed release tablets to suit an individual patient's needs.

Adaptation of pharmaceutical excipients to FDM 3D printing for the fabrication of patient-tailored immediate release tablets.

This work aims to employ fused deposition modelling 3D printing to fabricate immediate release pharmaceutical tablets with several model drugs. It investigates the addition of non-melting filler to methacrylic matrix to facilitate FDM 3D printing and explore the impact of (i) the nature of filler, (ii) compatibility with the gears of the 3D printer and iii) polymer: filler ratio on the 3D printing process. Amongst the investigated fillers in this work, directly compressible lactose, spray-dried lactose and microcrystalline cellulose showed a level of degradation at 135°C whilst talc and TCP allowed consistent flow of the filament and a successful 3D printing of the tablet. A specially developed universal filament based on pharmaceutically approved methacrylic polymer (Eudragit EPO) and thermally stable filler, TCP (tribasic calcium phosphate) was optimised. Four model drugs with different physicochemical properties were included into ready-to-use mechanically stable tablets with immediate release properties. Following the two thermal processes (hot melt extrusion (HME) and fused deposition modelling (FDM) 3D printing), drug contents were 94.22%, 88.53%, 96.51% and 93.04% for 5-ASA, captopril, theophylline and prednisolone respectively. XRPD indicated that a fraction of 5-ASA, theophylline and prednisolone remained crystalline whilst captopril was in amorphous form. By combining the advantages of thermally stable pharmaceutically approved polymers and fillers, this unique approach provides a low cost production method for on demand manufacturing of individualised dosage forms.

A Lower Temperature FDM 3D Printing for the Manufacture of Patient-Specific Immediate Release Tablets.

PURPOSE: The fabrication of ready-to-use immediate release tablets via 3D printing provides a powerful tool to on-demand individualization of dosage form. This work aims to adapt a widely used pharmaceutical grade polymer, polyvinylpyrrolidone (PVP), for instant on-demand production of immediate release tablets via FDM 3D printing. METHODS: Dipyridamole or theophylline loaded filaments were produced via processing a physical mixture of API (10%) and PVP in the presence of plasticizer through hot-melt extrusion (HME). Computer software was utilized to design a caplet-shaped tablet. The surface morphology of the printed tablet was assessed using scanning electron microscopy (SEM). The physical form of the drugs and its integrity following an FDM 3D printing were assessed using x-ray powder diffractometry (XRPD), thermal analysis and HPLC. In vitro drug release studies for all 3D printed tablets were conducted in a USP II dissolution apparatus. RESULTS: Bridging 3D printing process with HME in the presence of a thermostable filler, talc, enabled the fabrication of immediate release tablets at temperatures as low as 110°C. The integrity of two model drugs was maintained following HME and FDM 3D printing. XRPD indicated that a portion of the loaded theophylline remained crystalline in the tablet. The fabricated tablets demonstrated excellent mechanical properties, acceptable in-batch variability and an immediate in vitro release pattern. CONCLUSIONS: Combining the advantages of PVP as an impeding polymer with FDM 3D printing at low temperatures, this approach holds a potential in expanding the spectrum of drugs that could be used in FDM 3D printing for on demand manufacturing of individualised dosage forms.