Dynamic potential and surface morphology study of sertraline membrane sensors.

New rapid, sensitive and simple electrometric method was developed to determine sertraline hydrochloride (Ser-Cl) in its pure raw material and pharmaceutical formulations. Membrane sensors based on heteropolyacids as ion associating material were prepared. Silicomolybdic acid (SMA), silicotungstic acid (STA) and phosphomolybdic acid (PMA) were used. The slope and limit of detection are 50.00, 60.00 and 53.24 mV/decade and 2.51, 5.62 and 4.85 µmol L(-1) for Ser-ST, Ser-PM and Ser-SM membrane sensors, respectively. Linear range is 0.01-10.00 for the three sensors. These new sensors were used for the potentiometric titration of Ser-Cl using sodium tetraphenylborate as titrant. The surface morphologies of the prepared membranes with and without the modifier (ion-associate) were studied using scanning and atomic force microscopes.

Surface morphology changes of polymer membrane and carbon paste sertraline sensors.

Polymer membrane and chemically modified carbon paste (CMCP) sensors for determination of sertraline HCl (Ser-Cl) incorporating sertraline tetraphenylborate (Ser-TPB) as an electro-active material were constructed. They showed a rapid and linear response for Ser-ion over the concentration range 0.01-10.00 mmol L(-1). The limits of detection were 2.80 and 9.55 µmol L(-1), and Nernastian slopes were 56.60, 59.60 mV decade(-1) for membrane and CMCP sensors for batch method. In flow injection analysis (FIA), the electrodes revealed comparatively good selectivity for Ser-ion with regard to a wide variety of different cations, sugars, and amino acids. The addition of different anionic additives, namely sodium tetraphenylborate (NaTPB), potassium tetraphenylborate (KTPB), potassium tetrakis[3,5-bis-(triflouromethyl)phenyl]borate (KTFMPB), and sodium tetrakis[3,5-bis(trifluoro-methyl)phenyl]borate (NaTFMPB), to the prepared mixture improved their response characteristics. The surface morphologies of membrane films containing PVC only (blank), plasticizer+PVC, Ser-TPB+plasticizer+PVC, and Ser-TPB +plasticizer+PVC+additive were studied using scanning and atomic force electron microscopes. These sensors had been used in the potentiometric titration of Ser-ion against NaTPB. Standard addition method for the pure raw material and some of its pharmaceutical tablets was used for Ser-Cl determination. The obtained results were tested for their repeatability and reproducibility and were statistically treated by F- and t- tests.

Modified carbon paste sensor for the potentiometric determination of neostigmine bromide in pharmaceutical formulations, human plasma and urine.

A novel, simple, rapid, selective and sensitive method for the determination of neostigmine (Ns) ion in its bulk powder, different pharmaceutical dosage forms, and biological fluids (plasma and urine) using four modified carbon paste electrodes was developed. Sensor 1 is based on ion-association Ns-TPB, sensor 2 used Ns-PT, sensor 3 comprises a mixture of (Ns-PT+Ns-TPB) and sensor 4 was constructed using (Ns-PT+ß-CD). Solvent mediator 2-NPPE exhibited a proper behavior including Nernstian slope ranging from 61.5±0.5 to 64.5±0.5 mV per decade over the pH range of 3.8-10 for the four sensors. Linear responses of Ns within the concentration range 1.0×10(-7)-1.0×10(-2) mol/L were obtained. The response time is very short (≤10s) with a detection limit 6.3×10(-8) M. In flow injection analysis (FIA), sensor 3 shows a Nernstian slope value 75.5±0.5 mV per decade within the concentration range of 1×10(-6)-1×10(-2) mol/L and with a detection limit 7.5×10(-7) mol/L. The utility of mixed or additives of ß-CD had a significant influence on increasing the sensitivity of sensors 3 and 4 compared to sensors 1 and 2. The sensors were applied for the determination of neostigmine (Ns) ion in its bulk powder, different pharmaceutical dosage forms, and biological fluids (plasma and urine). The results obtained were satisfactory with excellent percentage recovery comparable with official method for the assay based on non-aqueous titration using perchloric acid as a titrant.

Single and mixed chemically modified carbon paste ion-selective electrodes for determination of ketotifen fumarate.

New modified carbon paste electrodes for determination of ketotifen fumarate in its pure and pharmaceutical preparations were constructed. The used modifiers are ketotifen phosphotungestate (Keto(3) PT), and ketotifen tetraphenylborate (Keto-TPB). Single and mixed ion-associate electrodes were prepared. Both Keto-TPB and mixed (Keto-TPB and Keto(3) PT) electrodes have a linearity range of 1.00 × 10(-5) -1.00 × 10(-2) mol L(-1) . The slopes were 58.30 and 54.20 mV/decade for Keto-TPB and mixed chemically modified carbon paste electrodes (CMCPE), respectively. The limits of detection were 1.42 × 10(-6) and 1.00 × 10(-5) mol L(-1) for Keto-TPB and mixed CMCPEs, respectively. The potential variation due to pH change is considered acceptable in the pH ranges 4.44-9.11 and 2.50-9.00 for Keto-TPB and mixed ion-exchanger CMCPE, respectively. The response time was ≤10 s for both electrodes. Selectivity coefficients values towards different inorganic cations, sugars, and amino acids reflect high selectivity of the prepared electrodes. Potentiometric titrations and standard addition methods were applied for the determination of ketotifen ion in its pure samples and pharmaceutical formulations (Zaditen tablet and syrup) using proposed electrodes. The electrodes were also tested in flow injection analysis (FIA). The results obtained from both methods were statistically treated by F- and t-tests. The carbon paste electrodes have the advantages of being more easily prepared and longer life span compared to the plastic membrane electrodes previously reported.

Spectral investigation of the intramolecular charge-transfer in some aminotriazole Schiff bases.

3-Amino-1,2,4-triazole Schiff bases were reported to contain intramolecular charge-transfer. The enhancing and depressing effects were remarkable as the substituent was changed from electron-donating to electron-withdrawing groups. The path of the resonating delocalization was reversed in the case of the p-NO2 group. To validate these results we effectively used Weinhold et al's natural bond orbital analysis to assess the UV and FT-IR spectrophotometric monitoring of the change reflected in this phenomenon when the substituent in the benzene ring is altered. The NBO analysis was simulated by ab inito computations at the HF/6-31G(d) level of theory, in order to properly detect any possible presence of a hydrogen bond association. The changes occurring in electron occupancies of double-centered bonds, antibonding orbitals and in lone-pair orbitals appraised the results, as did the s and p character listings of the two-centered bonds and the simultaneous changes occurring in the geometric parameters of the molecules in question. Contrary to its normal preference, in these molecules the nitrogen used sp2 hybrid orbitals for its interaction, housing its electron lone-pair in the third p hybrid orbital. Furthermore, NBO analysis reflected the presence of a very soft intramolecular hydrogen association (C-H⋯π), labelled by UV and FT-IR assignments, between the benzene and triazole rings in all Schiff bases but p-N(Me)2. The n-π* stabilization energy decreased in the order: p-OH>p-OCH3>p-Cl>p-CH3>H>p-NO2>o-OH. The relation between the band position and Hammett substitution constant is interpreted in relation to the molecular structure.

New selenite ion-selective electrodes based on 5,10,15,20-tetrakis-(4-methoxyphenyl)-21H,23H-porphyrin-Co(II).

New polymeric membrane (PME), modified carbon paste (MCPE), and coated wire (CWE) selenite ion-selective electrodes based on 5,10,15,20-tetrakis-(4-methoxyphenyl)-21H,23H-porphyrin-Co(II) (CoTMeOPP) are reported. The best composition was the electrode containing 2% CoTMeOPP as the active material and 49% TCP as plasticizer. The electrodes reveal a Nernstian behavior over a concentration range of 5.5x10(-5) to 1.1x10(-2) M for PME, 5.2x10(-5) to 1.2x10(-2) M for MCPE and 1.2x10(-4) to 4.4x10(-3) M for CWE. The potentiometric response is pH dependent, since selenous acid is a diprotic acid. The slope of the selenite PVC electrode was -57.0 mV for the monovalent anion at pH 6.47, and -26.0 mV for the divalent anion at pH 11.00. The detection limits were 3.4x10(-5) and 4.7x10(-5) M at pH values 6.47 and 11.00, respectively. The electrodes manifest advantages of low resistance, very short response time (15 s), and most importantly good selectivities relative to a wide variety of other anions. In fact, the proposed selenite ion-selective electrodes show a great improvement compared to previously reported electrodes for selenite ion. The electrode was used for the determination of selenite in selenite/selenate mixture, in sodium selenite raw material powder, and in VitaFit Selenium ACE antioxidant tablets with recovery ranges of 90.0-103.3%.

Spectrophotometric determination of sildenafil citrate in pure form and in pharmaceutical formulation using some chromotropic acid azo dyes.

Two simple and highly sensitive spectrophotometric methods were developed for the quantitative determination of the drug sildenafil citrate (SC), Viagra, in pure form and in pharmaceutical formulations, through ion-associate formation reactions (method A) with mono-chromotropic acid azo dyes, chromotrope 2B (I) and chromotrope 2R (II) and ion-pair reactions (method B) with bi-chromotropic acid azo dyes, 3-phenylazo-6-o-carboxyphenylazo-chromotropic acid (III), bis-3,6-(o-hydroxyphenylazo)-chromotropic acid (IV), bis-3,6-(p-N,N-dimethylphenylazo)-chromotropic acid (V) and 3-phenylazo-6-o-hydroxyphenylazo-chromotorpic acid (VI). The reaction products, extractable in methylene chloride, were quantitatively measured at 540, 520, 540, 570, 600 and 575 nm using reagents, I-VI, respectively. The reaction conditions were studied and optimized. Beer's plots were linear in the concentration ranges 3.3-87.0, 3.3-96.0, 5.0-115.0, 2.5-125.0, 8.3-166.7 and 0.8-15.0 microg mL(-1) with corresponding molar absorptivities 1.02 x 10(4), 8.34 x 10(3), 6.86 x 10(3), 5.42 x 10(3), 3.35 x 10(3) and 2.32 x 10(4)Lmol(-1) cm(-1) using reagents I-VI, respectively. The limits of detection and Sandell's sensitivities were calculated. The methods were successfully applied to the analysis of commercial tablets (Vigoran) and the recovery study reveals that there is no interference from the common excipients that are present in tablets. Statistical comparison of the results was performed with regard to accuracy and precision using Student's t- and F-tests at 95% confidence level. There is no significant difference between the reported and proposed methods with regard to accuracy and precision.

Sibutramine selective electrodes for batch and flow injection determinations in pharmaceutical preparations.

The construction and electrochemical response characteristics of two new polyvinyl chloride (PVC) membrane sensors for the determination of sibutramine hydrochloride were described. The sensors are based on the ion association complexes of sibutramine with sodium tetraphenylborate (NaTPB) or phosphotungstic acid (PTA) using dibutyl phthalate as plasticizing solvent. The sensors display a fast, stable response over the concentration range 3.84 x 10(-5)-1.00 x 10(-2) M sibutramine hydrochloride monohydrate (SibuCl), with cationic slopes of 57.7 +/- 0.57 and 59.7 +/- 1.79 mV concentration decade(-1) and detection limits of 8.91 x 10(-6) and 1.47 x 10(-5) M in case of sibutramine-tetraphenylborate (Sibu-TPB) and sibutramine-phosphotungstate ((Sibu)(3)-PT), respectively. The proposed sensors have been successfully applied for the determination of sibutramine hydrochloride in Regitrim capsules in batch and flow injection (FI) conditions.

1H NMR, 13C NMR and mass spectral studies of some Schiff bases derived from 3-amino-1,2,4-triazole.

Heterocyclic Schiff bases derived from 3-amino-1,2,4-triazole and different substituted aromatic aldehydes are prepared and subjected to (1)H NMR, (13)C NMR and mass spectral analyses. (1)H NMR spectra in DMSO exhibit a sharp singlet within the 9.35-8.90ppm region which corresponds to the azomethine proton. The position of this signal is largely dependent on the nature of the substituents on the benzal moiety. It is observed that the shape, position and the integration value of the signal of the aromatic proton of the triazole ring ((5)C) are clearly affected by the rate of exchange, relaxation time, concentration of solution as well as the solvent used. (13)C NMR is taken as substantial support for the results reached from (1)H NMR studies. The mass spectral results are taken as a tool to confirm the structure of the investigated compounds. The base peak (100%), mostly the M-1 peak, indicates the facile loss of hydrogen radical. The fragmentation pattern of the unsubstituted Schiff base is taken as the general scheme. Differences in the other schemes result from the effect of the electronegativity of the substituents attached to the aromatic ring.

Flow injection determination of ketotifen fumarate using PVC membrane selective electrodes.

In this study a PVC membrane electrode for determination of ketotifen fumarate is reported, where ketotifen tetraphenylborate (Keto-TPB) was used as ion exchanger. The electrode has linear range of 5.6x10(-6)-1.0x10(-2) and 1.0x10(-5)-1.0x10(-2) mol/L, with detection limits 2.37x10(-6)and 4.60x10(-6) mol/L in batch and flow injection analysis (FIA), respectively. The electrodes show a Nernstian slope value (58.40 and 61.50 mV/decade in batch and FIA, respectively), and the response time is very short (

Cathodic adsorptive stripping voltammetry of drotaverine hydrochloride and its determination in tablets and human urine by differential pulse voltammetry.

The stripping voltammetric behaviour of drotaverine hydrochloride (DvCl) was studied using a hanging mercury drop electrode (HMDE). The adsorptive stripping response has been evaluated with respect to pH, accumulation time, accumulation potential, scan rate and other variables. Differential pulse DP mode; over the potential range -400 to -1200 mV, is used in the presence of 0.04 M Britton-Robinson buffer pH 2. Cyclic voltammetric study indicates that the reduction process is irreversible and controlled by adsorption. The response of DP technique is linear over the concentration range 21.70-257.34 ng/ml. Limit of detection and limit of quantification were 3.15 and 10.50 ng/ml, respectively. The proposed method was successfully applied for the determination of the drug in commercial tablets and spiked human urine samples.

Improving the detection limits of antispasmodic drugs electrodes by using modified membrane sensors with inner solid contact.

Three coated wire electrodes (CWEs) for the antispasmodic drugs; dicyclomine (Dc), mebeverine (Mv) and drotaverine (Dv) hydrochlorides were developed. Each electrode based on ion-associate of a heteropoly anion with the drug cation incorporated in membrane sensor modified with graphite and deposited on silver internal solid contact. The influence of addition of graphite to the membranes and the type of the internal solid contact on the potentiometric responses of the electrodes was investigated. The characteristics of the new electrodes were compared to the characteristics of previously reported traditional liquid inner contact electrodes of the same drugs. The lower detection limits of the proposed electrodes were somewhat better than those observed with the corresponding liquid contact ISEs and reached (1.2-2.0)x10(-7)M. The potentiometric selectivity of the CWEs revealed a significant improvement and much faster response times compared to the liquid contact ISEs. The practical utility of each electrode has been demonstrated by using it successfully in potentiometric determination of its respective drug in pharmaceutical preparations both in batch and flow injection conditions. Each electrode was also used as an indicator electrode in the potentiometric titration of the drug against standard silicotungstic acid and in potentiometric determination of the drug concentration in urine samples.

Spectrophotometric Determination of Diazepam in Pure form, Tablets and Ampoules.

The interaction of diazepam with picric acid (I), 3,5-dinitrobenzoic acid (II) and 2,4-dinitrobenzoic acid (III) was found to be useful for its spectrophotometric determination. The quantitation was carried out at 475, 500, and 500 nm for the reaction with (I), (II) and (III), respectively. The effect of several variables on the coloring process was studied. The proposed methods have been applied successfully for the determination of diazepam in pure samples and in its pharmaceutical preparations with good accuracy and precision. The results were compared to those obtained by the pharmacopoeial methods. The linear ranges for obedience of Beer's law are up to 85.6, 180.2, and 128.6 µg/ml, Ringbom ranges are 10.0-79.0, 15.2-177.8, 17.0-83.0 µg/ml, and RSD 0.048, 0.028, and 0.026% for reaction of diazepam with I, II, and III, respectively.

Studies on some salicylaldehyde Schiff base derivatives and their complexes with Cr(III), Mn(II), Fe(III), Ni(II) and Cu(II).

The formation constants of some transition metal ions Cr(III), Mn(II), Fe(III), Ni(II) and Cu(II) binary complexes containing Schiff bases resulting from condensation of salicylaldehyde with aniline (I), 2-aminopyridine (II), 4-aminopyridine (III) and 2-aminopyrimidine (IV) were determined pH-metrically in ethanolic medium (80%, v/v). The formation constants were determined for all binary complexes. The important infrared (IR) spectral bands corresponding to the active groups in the four ligands and the solid complexes under investigation were studied. The solid complexes have been synthesized and studied by thermogravimetric analysis. The thermal dehydration and decomposition of these complexes were studied kinetically using the integral method applying the Coats-Redfern equation. It was found that the thermal decomposition of the complexes follow second order kinetics. The thermodynamic parameters of the decomposition are also reported. The electronic absorption spectra of the investigated ligands were carried out to determine the pK(a) values spectrophotometrically.

The surfactant sensitized analytical reaction of cerium(IV) with some triphenylformazan derivatives.

Cationic surfactant, cetylpyridinium bromide (CPB), sensitizes the colour reaction of cerium(IV) with 1,3-o-hydroxyphenyl-5-phenylformazan(I), 1-m-hydroxyphenyl-3-o-hydroxyphenyl-5-phenylformazan(II) and 1-m-carboxyphenyl-3-o-hydroxyphenyl-5-phenylformazan(III). The formation of a soluble ternary complex of stoichiometric ratio 1:1:1 (Ce(IV)-R-CPB) is responsible for the observed enhancement in the molar absorptivity and Sandell sensitivity of the formed complex, when a surfactant is present. The ternary complex exhibits absorption maxima at 596, 571 and 607 nm (epsilon=6.05 x 10(4), 6.28 x 10(4) and 8.06 x 10(4)L mol(-1)cm(-1)) using triphenylformazan derivatives I, II and III, respectively. Beer's law is obeyed between 0.15 and 2.5 microg ml(-1), whereas, optimum concentration range applying Ringbom method is in the range 0.30-2.25 microg ml(-1). Conditional formation constants in the presence and absence of CPB for Ce(IV) complexes have been calculated. The proposed method has been successfully applied to the analysis of magnesium-base cerium alloys and synthetic mixtures corresponding to various cerium alloys.

Flow injection potentiometric determination of clobutinol hydrochloride.

New clobutinol (Clob) ion-selective polyvinyl chloride (PVC) membrane electrodes, based on the ion-associates of Clob with phosphotungstic acid or phosphomolybdic acid were prepared using dibutyl phthalate as plasticizing solvent. The electrodes were characterized in terms of membrane composition, temperature and pH. The sensors showed a near-Nernstian response over the concentration ranges (6.31 x 10(-6))-(1.00 x 10(-2)) and (5.01 x 10(-5))-(1.00 x 10(-2))M in the case of clobutinol-phosphotungstate ((Clob)(3)-PT) applying batch and flow injection (FI) analysis, respectively, and (1.58 x 10(-5))-(1.00 x 10(-2)) and (5.01 x 10(-5))-(1.00 x 10(-2))M in case of clobutinol-phosphomolybdate ((Clob)(3)-PM) for batch and FI analysis systems, respectively. The electrodes were successfully applied for the potentiometric determination of ClobCl in pharmaceutical preparation and urine in steady state and flow injection conditions. The electrodes exhibit good selectivity for Clob with respect to a large number of inorganic cations, sugars and amino acids.

New conventional coated-wire ion-selective electrodes for flow-injection potentiometric determination of chlordiazepoxide.

New chlordiazepoxide hydrochloride (Ch-Cl) ion-selective electrodes (conventional type) based on ion associates, chlordiazepoxidium-phosphomolybdate (I) and chlordiazepoxidium-phosphotungstate (II), were prepared. The electrodes exhibited mean slopes of calibration graphs of 59.4 mV and 60.8 mV per decade of (Ch-Cl) concentration at 25 degrees C for electrodes (I) and (II), respectively. Both electrodes could be used within the concentration range 3.16 x 10(-6)-1 x 10(-2) M (Ch-Cl) within the pH range 2.0-4.5. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficients of the electrodes, which were 0.00139 and 0.00093 V degrees C(-1) for electrodes (I) and (II), respectively. The electrodes showed a very good selectivity for Ch-Cl with respect to the number of inorganic cations, amino acids and sugars. The electrodes were applied to the potentiometric determination of the chlordiazepoxide ion and its pharmaceutical preparation under batch and flow injection conditions. Also, chlordiazepoxide was determined by conductimetric titrations. Graphite, copper and silver coated wires were prepared and characterized as sensors for the drug under investigation.

Chemically modified carbon paste electrode for the potentiometric determination of dicylomine hydrochloride in batch and in FIA conditions.

A carbon-paste electrode for dicyclomine hydrochloride (DcCl) was prepared and fully characterized in terms of composition, life span, usable pH range and temperature. The electrode was applied to the potentiometric determination of dicylominium ion in its pure state and in pharmaceutical preparations in batch and flow injection conditions and in biological fluids using standard additions method. The electrode is based on a mixture of two ion-exchangers, namely, dicyclominium-phosphomolybdate and dicylominium-tetraphenylborate, dissolved in dioctyl phthalate as pasting liquid. The modified electrode showed a near-Nernstian slope of 58 +/- 2 mV over the concentration range of 1.2 x 10(-5)-1.6 x 10(-2) M with an average recovery of 97-102% and a RSD of 0.090-1.00. The electrode exhibits good selectivity for DcCl with respect to a large number of inorganic cations, sugars, amino acids and organic substances of biological fluids. Potentiometric titrations of DcCl with several titrants have been monitored using this modified carbon paste electrode as an end-point indicator electrode.

Construction and analytical applications of plastic membrane electrode for oxymetazoline hydrochloride.

A new oxymetazoline (OM) ion-selective PVC membrane electrode based on the ion associate of OM with phosphotungstic acid was prepared. The electrode exhibits a linear response with a mean calibration graph slope of 57.16 mV decade(-1) at 25 degrees C within the concentration range of 1.96 x 10(-5) - 1 x 10(-2) M OMCl. The change in the pH within the range of 1.0 - 9.4 did not affect the electrode performance. The standard electrode potentials were determined at different temperatures and used to calculate the isothermal coefficient of the electrode (-0.001233 V). The electrode showed a very good selectivity for OM with respect to a large number of inorganic cations and compounds. The standard addition method and potentiometric titration were applied to the determination of (OM) with RSD not exceeding 1.19%.

Quantitative determination of some pharmaceutical piperazine derivatives through complexation with iron(III) chloride.

A simple, accurate and sensitive spectrophotometric method has been developed for the determination of three pharmaceutical piperazine derivatives, namely ketoconazole (KC), trimetazidine hydrochloride (TMH) and piribedil (PD). This method is based on the formation of yellow orange complexes between iron(III) chloride and the investigated drugs. The optimum reaction conditions, spectral characteristics, conditional stability constants and composition of the water soluble complexes have been established. The method permits the determination of KC, TMH and PD over a concentration range 1-15, 1-12 and 1-12 microg ml(-1), respectively. Sandell sensitivity is found to be 0.016, 0.013 and 0.013 microg cm(-2) for KC, TMH and PD, respectively. The method was sensitive, simple, reproducible and accurate within +/-1.5%. The method is applicable to the assay of the three drugs under investigation in different dosage forms and the results are in good agreement with those obtained by the official methods (USP and JP).