Flexible and wavelength-independent optical transmission for laser pointing stabilization and assembly error compensation.

A flexible light guide was developed for an ITER (International Thermonuclear Experimental Reactor) poloidal polarimeter which is a passive laser beam alignment and stabilization system for free-space propagation of a wide range of wavelengths. The advantages of using a flexible light guide are (1) to compensate the relative movement between the floor of a building and an optical table, (2) to negate assembly error of the optical transmission line, (3) to minimize the time required for assembly of the line and laser position alignment in a radiological environment, and (4) to transmit a wide wavelength range from visible to far-infrared. The authors fabricated a flexible light guide with an inner diameter of 120 mm and with a motion range of 10 cm. Pointing stability of the laser beam passing through the flexible light guide was less than 70 µrad when the support moved ±50 mm. A flexible light guide error of 70 µrad leads to a beam position displacement of 0.98 mm at a beam position steering mirror ITER poloidal polarimeter that is located 14 m from the flexible light guide. The achieved error is stable enough to guide the laser beam to its target in ITER.

Note: Lossless laser beam combiner employing a high-speed rotating half-wave plate.

We have developed a laser beam combiner employing a high-speed rotating half-wave plate based on the specific requirements of the Thomson scattering measurement systems in the ITER. The polarization extinction ratio of the output beam may exceed 1000 and was maintained for more than 1 h via feedback control of the half-wave plate rotation speed. The pointing fluctuations introduced by rotating the half-wave plate were in the order of microradians. The high-speed rotating half-wave plate provides a lossless means of combining laser beams together with stable beam pointing.

Note: Optimization of magnifying a polarization angle with Littrow layout blazed gratings.

Magnification of a polarization angle with Littrow layout gratings has been developed. High magnification with a factor of 7.7 using two gratings in Littrow layout was experimentally proved. The magnification range was investigated by calculation at a wavelength of 10.6 µm. The method can be applied for a high magnification factor >30. Larger groove numbers and smaller blaze angles are suitable for the large magnification. Statistical fluctuation of the diffracted polarization angle is compared with that of the incident polarization angle.

Validations of calibration-free measurements of electron temperature using double-pass Thomson scattering diagnostics from theoretical and experimental aspects.

This paper evaluates the accuracy of electron temperature measurements and relative transmissivities of double-pass Thomson scattering diagnostics. The electron temperature (Te) is obtained from the ratio of signals from a double-pass scattering system, then relative transmissivities are calculated from the measured Te and intensity of the signals. How accurate the values are depends on the electron temperature (Te) and scattering angle (θ), and therefore the accuracy of the values was evaluated experimentally using the Large Helical Device (LHD) and the Tokyo spherical tokamak-2 (TST-2). Analyzing the data from the TST-2 indicates that a high Te and a large scattering angle (θ) yield accurate values. Indeed, the errors for scattering angle θ = 135° are approximately half of those for θ = 115°. The method of determining the Te in a wide Te range spanning over two orders of magnitude (0.01-1.5 keV) was validated using the experimental results of the LHD and TST-2. A simple method to provide relative transmissivities, which include inputs from collection optics, vacuum window, optical fibers, and polychromators, is also presented. The relative errors were less than approximately 10%. Numerical simulations also indicate that the Te measurements are valid under harsh radiation conditions. This method to obtain Te can be considered for the design of Thomson scattering systems where there is high-performance plasma that generates harsh radiation environments.

Development of real-time rotating waveplate Stokes polarimeter using multi-order retardation for ITER poloidal polarimeter.

The rotating waveplate Stokes polarimeter was developed for ITER (International Thermonuclear Experimental Reactor) poloidal polarimeter. The generalized model of the rotating waveplate Stokes polarimeter and the algorithm suitable for real-time field-programmable gate array (FPGA) processing were proposed. Since the generalized model takes into account each component associated with the rotation of the waveplate, the Stokes parameters can be accurately measured even in unideal condition such as non-uniformity of the waveplate retardation. Experiments using a He-Ne laser showed that the maximum error and the precision of the Stokes parameter were 3.5% and 1.2%, respectively. The rotation speed of waveplate was 20 000 rpm and time resolution of measuring the Stokes parameter was 3.3 ms. Software emulation showed that the real-time measurement of the Stokes parameter with time resolution of less than 10 ms is possible by using several FPGA boards. Evaluation of measurement capability using a far-infrared laser which ITER poloidal polarimeter will use concluded that measurement error will be reduced by a factor of nine.

Signal evaluations using singular value decomposition for Thomson scattering diagnostics.

This paper provides a novel method for evaluating signal intensities in incoherent Thomson scattering diagnostics. A double-pass Thomson scattering system, where a laser passes through the plasma twice, generates two scattering pulses from the plasma. Evaluations of the signal intensities in the spectrometer are sometimes difficult due to noise and stray light. We apply the singular value decomposition method to Thomson scattering data with strong noise components. Results show that the average accuracy of the measured electron temperature (Te) is superior to that of temperature obtained using a low-pass filter (<20 MHz) or without any filters.

Note: Magnification of a polarization angle with a Littrow layout brazed grating.

A new method to magnify a small polarization angle with brazed gratings has been developed. In the method, difference in diffraction efficiency for S and P polarization components is used. The magnification dependence on the incident angle can be small by arranging the grating in Littrow layout. A magnification with a factor ~2.7 has been demonstrated for a 10.6 µm CO2 laser beam as expected from a calculation. The method is applicable in many polarimetry fields.

Chevron beam dump for ITER edge Thomson scattering system.

This paper contains the design of the beam dump for the ITER edge Thomson scattering system and mainly concerns its lifetime under the harsh thermal and electromagnetic loads as well as tight space allocation. The lifetime was estimated from the multi-pulse laser-induced damage threshold. In order to extend its lifetime, the structure of the beam dump was optimized. A number of bent sheets aligned parallel in the beam dump form a shape called a chevron which enables it to avoid the concentration of the incident laser pulse energy. The chevron beam dump is expected to withstand thermal loads due to nuclear heating, radiation from the plasma, and numerous incident laser pulses throughout the entire ITER project with a reasonable margin for the peak factor of the beam profile. Structural analysis was also carried out in case of electromagnetic loads during a disruption. Moreover, detailed issues for more accurate assessments of the beam dump's lifetime are clarified. Variation of the bi-directional reflection distribution function (BRDF) due to erosion by or contamination of neutral particles derived from the plasma is one of the most critical issues that needs to be resolved. In this paper, the BRDF was assumed, and the total amount of stray light and the absorbed laser energy profile on the beam dump were evaluated.

Optical designs of reflection and refraction collection optics for a JT-60SA core Thomson scattering system.

Collection optics for core measurements in a JT-60SA Thomson scattering system were designed. The collection optics will be installed in a limited space and have a wide field of view and wide wavelength range. Two types of the optics are therefore suggested: refraction and reflection types. The reflection system, with a large primary mirror, avoids large chromatic aberrations. Because the size limit of the primary mirror and vignetting due to the secondary mirror affect the total collection throughput, conditions that provide the high throughput are found through an optimization. A refraction system with four lenses forming an Ernostar system is also employed. The use of high-refractive-index glass materials enhances the freedom of the lens curvatures, resulting in suppression of the spherical and coma aberration. Moreover, sufficient throughput can be achieved, even with smaller lenses than that of a previous design given in [H. Tojo, T. Hatae, T. Sakuma, T. Hamano, K. Itami, Y. Aida, S. Suitoh, and D. Fujie, Rev. Sci. Instrum. 81, 10D539 (2010)]. The optical resolutions of the reflection and refraction systems are both sufficient for understanding the spatial structures in plasma. In particular, the spot sizes at the image of the optics are evaluated as ~0.3 mm and ~0.4 mm, respectively. The throughput for the two systems, including the pupil size and transmissivity, are also compared. The results show that good measurement accuracy (<10%) even at high electron temperatures (<30 keV) can be expected in the refraction system.

Identification of errors in the electron density measurements of a tangential interferometer∕polarimeter system during a tokamak discharge.

A new method for the comparative verification of electron density measurements obtained with a tangential interferometer and a polarimeter during a discharge is proposed. The possible errors associated with the interferometer and polarimeter are classified by the time required for their identification. Based on the characteristics of the errors, the fringe shift error of the interferometer and the low-frequency noise of the polarimeter were identified and corrected for the JT-60U tangential interferometer∕polarimeter system.

Anisotropic electron temperature measurements without knowing the spectral transmissivity for a JT-60SA Thomson scattering diagnostic.

This paper focuses on a method for measuring the electron temperature (T(e)) without knowing the transmissivity using Thomson scattering diagnostic with a double-pass scattering system. Application of this method for measuring the anisotropic T(e), i.e., the T(e) in the directions parallel (T(eparallel)) and perpendicular (T(eperpendicular)) to the magnetic field, is proposed. Simulations based on the designed parameters for a JT-60SA indicate the feasibility of the measurements except in certain T(e) ranges, e.g., T(eparallel) ~ 3.5T(eperpendicular) at 120° of the scattering angle.

First measurement of electron temperature from signal ratios in a double-pass Thomson scattering system.

This paper presents an experimental demonstration to determine electron temperature (T(e)) with unknown spectral sensitivity (transmissivity) in a Thomson scattering system. In this method, a double-pass scattering configuration is used and the scattered lights from each pass (with different scattering angles) are measured separately. T(e) can be determined from the ratio of the signal intensities without knowing a real chromatic dependence in the sensitivity. Note that the wavelength range for each spectral channel must be known. This method was applied to the TST-2 Thomson scattering system. As a result, T(e) measured from the ratio (T(e,r)) and T(e) measured from a standard method (T(e,s)) showed a good agreement with <∣T(e,r) - T(e,s)∣∕T(e,s)> = 7.3%.

Design of collection optics and polychromators for a JT-60SA Thomson scattering system.

This paper presents designs of collection optics for a JT-60SA Thomson scattering system. By using tangential (to the toroidal direction) YAG laser injection, three collection optics without strong chromatic aberration generated by the wide viewing angle and small design volume were found to measure almost all the radial space. For edge plasma measurements, the authors optimized the channel number and wavelength ranges of band-pass filters in a polychromator to reduce the relative error in T(e) by considering all spatial channels and a double-pass laser system with different geometric parameters.

Diversity-oriented synthesis of multisubstituted olefins through the sequential integration of palladium-catalyzed cross-coupling reactions. 2-pyridyldimethyl(vinyl)silane as a versatile platform for olefin synthesis.

A novel strategy for the diversity-oriented synthesis of multisubstituted olefins, where 2-pyridyldimethyl(vinyl)silane functions as a versatile platform for olefin synthesis, is described. The palladium-catalyzed Heck-type coupling of 2-pyridyldimethyl(vinyl)silanes with organic iodides took place in the presence of Pd2(dba)3/tri-2-furylphosphine catalyst to give beta-substituted vinylsilanes in excellent yields. The Heck-type coupling occurred even with alpha- and beta-substituted 2-pyridyldimethyl(vinyl)silanes. The one-pot double Heck coupling of 2-pyridyldimethyl(vinyl)silane took place with two different aryl iodides to afford beta,beta-diarylated vinylsilanes in good yields. The palladium-catalyzed Hiyama-type coupling of 2-pyridyldimethyl(vinyl)silane with organic halides took place in the presence of tetrabutylammonium fluoride to give di- and trisubstituted olefins in high yields. The sequential integration of Heck-type (or double Heck) coupling and Hiyama-type coupling produced the multisubstituted olefins in regioselective, stereoselective, and diversity-oriented fashions. Especially, the one-pot sequential Heck/Hiyama coupling reaction provides an extremely facile entry into a diverse range of stereodefined multisubstituted olefins. Mechanistic considerations of both Heck-type and Hiyama-type coupling reactions are also described.

Unusually accelerated silylmethyl transfer from tin in stille coupling: implication of coordination-driven transmetalation.

The palladium-catalyzed cross-coupling reaction of 2-PyMe2SiCH2SnBu3 with aryl iodide (Ar-I) exclusively produced the 2-PyMe2SiCH2 transferred product 2-PyMe2SiCH2Ar. The relative transfer ability of organic group from tin was found to be 2-PyMe2SiCH2 >> Ph > Me > Bu >> PhMe2SiCH2, which implies the beneficial pyridyl-to-palladium coordination effect. Thus, the transfer of the silylmethyl group from tin to palladium was remarkably accelerated by simply appending the 2-pyridyl group on silicon. The pyridyl-to-palladium coordination was validated in the palladium(II) complex 2-PyMe2SiCH2PdClPPh3 by 1H NMR and X-ray crystal structure analysis. The cross-coupling product was used for further transformations. The C-Si oxidation of the cross-coupling product 2-PyMe2SiCH2Ar afforded ArCH2OH in high yield. The fluoride ion-catalyzed 1,2-addition of 2-PyMe2SiCH2Ar to carbonyl compound (RR'C=O) gave ArCH2C(OH)RR' in high yield.

Pyridyl group assisted deprotonation of a methyl group on silicon: complex induced proximity effect and novel hydroxymethylation.

A novel methodology for the deprotonation of a methyl group on silicon has been developed. This newly developed alpha-lithiation protocol is based on the intramolecular pyridyl group coordination to stabilize the alpha-silyl carbanion together with the inherent silicon alpha effect. It was found that the deprotonation (t-BuLi/Et(2)O/-78 degrees C) occurs with 2-pyridyltrimethylsilane but not with other related silanes such as phenyltrimethylsilane, 3-pyridyltrimethylsilane, and 4-pyridyltrimethylsilane. It seems that this deprotonation proceeded through the agency of the complex-induced proximity effect (CIPE) of a 2-pyridyl group on silicon. (1)H NMR analysis of (2-pyridyldimethylsilyl)methyllithium revealed the intramolecular coordination of a pyridyl group to lithium. (2-Pyridyldimethylsilyl)methyllithium was found to react with chlorosilanes, hydrosilanes, chlorostannanes, bromine, iodine, organic bromides, aldehydes, and ketones in good to excellent yields. The resultant adducts were further oxidized with H(2)O(2)/KF to give the corresponding alcohols in excellent yields. Thus, this two-step transformation provides an efficient method for the nucleophilic hydroxymethylation.

Measurement of natural plasma flow along the field lines in the scrape-Off layer on the JT-60U divertor tokamak

The plasma profile and parallel plasma flow in the scrape-off layer (SOL) were systematically measured using reciprocating Mach probes installed at the outer midplane and near the divertor magnetic null (x point) in the JT-60U tokamak with a single null divertor. For the ion vertical drift due to the toroidal magnetic field gradient (ion nablaB drift) directed towards the divertor, SOL plasma flow along the magnetic field lines away from the divertor ("flow reversal") was discovered at the midplane far from the divertor. A quantitative evaluation of the ion "Pfirsch-Schluter flow," wherein the parallel flow is naturally produced in a toroidal plasma, was consistent with the measurement.

[Bis]

[formula: see text] The generation of (2-PyMe2Si)2CHLi was easily accomplished by the deprotonation of (2-PyMe2Si)2CH2 using n-BuLi in Et2O. Thus generated (2-PyMe2Si)2CHLi was found to react with a variety of aldehydes and ketones to give the corresponding vinylsilanes in extremely high yields with complete stereoselectivities.