Multifunctional leather finishing vs. applications, through the addition of well-dispersed flower-like nanoparticles.

In the present paper, multifunctional flower-like nanoparticles were synthesized to be used in the leather finishing. They are capable of conferring simultaneously and synergistic antimicrobial, self-cleaning, light resistance, hydrophobic, mechanical, thermal, and fluorescent properties due to the presence of Ag, TiO2, and SiO2 NPs. These nanoparticles form a "flower-like" structure in which the "pistil" is made up of TiO2 and the "petals" that surround it of silver nanoparticles and silica nanoparticles, whose dimensions are of the order of ten nanometers. Their surfaces enjoy abundant hydrophilic functionalities to be dispersed within inks commonly used during the leather finishing process. Leathers functionalized with these nanomaterials showed significantly improved self-cleaning properties after 15 h of exposure to UV light, and antibacterial properties 10 times higher than that shown by the untreated samples. Aging tests were performed (ISO 105-B02, ISO 17228, SAEJ 2412). ΔE, color variation decreased by approximately 30%, if compared with samples not refined with flower-like NPs. Furthermore, the results of the mechanical tests (ISO 17076, FCA 50444) evidence amazing properties, e.g. abrasion resistance more than significantly improved, increase in resistance from 1500 cycles for the untreated samples to 3000 cycles for the leathers finished with flower-like NPs. The contact angle analysis, capturing the angle that traces the air-water to water-substrate interface from the origin of the air-water-substrate contact point at the edge, is practically unchanged after 10 s in the case of nanoparticles containing finishing.

Rough and Porous Micropebbles of CeCu2Si2 for Energy Storage Applications.

Supercapacitors have attracted considerable attention due to their advantages, including being lightweight and having rapid charge-discharge, a good rate capability, and high cyclic stability. Electrodes are one of the most important factors influencing the performance of supercapacitors. Herein, a three-dimensional network of rough and porous micropebbles of CeCu2Si2 has been prepared using a one-step procedure and tested for the first time as a supercapacitor electrode. The synthesized material was extensively characterized in a three-electrode configuration using different electrochemical techniques, such as cyclic voltammetry (CV), galvanostatic charge and discharge (GCD) tests, and electrochemical impedance spectroscopy (EIS). CeCu2Si2 shows rather high mass-capacitance values: 278 F/g at 1 A/g and 295 F/g at 10 mV/s. Moreover, the material exhibits remarkable long-term stability: 98% of the initial capacitance was retained after 20,000 cycles at 10 A/g and the Coulombic efficiency remains equal to 100% at the end of the cycles.

Iron Selenide Particles for High-Performance Supercapacitors.

Nowadays, iron (II) selenide (FeSe), which has been widely studied for years to unveil the high-temperature superconductivity in iron-based superconductors, is drawing increasing attention in the electrical energy storage (EES) field as a supercapacitor electrode because of its many advantages. In this study, very small FeSe particles were synthesized via a simple, low-cost, easily scalable, and reproducible solvothermal method. The FeSe particles were characterized using cyclic voltammetry (CV), galvanostatic charge/discharge (GCD) measurements, and electrochemical impedance spectroscopy (EIS), revealing enhanced electrochemical properties: a high capacitance of 280 F/g at 0.5 A/g, a rather high energy density of 39 Wh/kg and a corresponding power density of 306 W/kg at 0.5 A/g, an extremely high cycling stability (capacitance retention of 92% after 30,000 cycles at 1 A/g), and a rather low equivalent series resistance (RESR) of ~2 Ω.

A New Route for Low Pressure and Temperature CWAO: A PtRu/MoS2_Hyper-Crosslinked Nanocomposite.

PtRu/MoS2 nanoparticles (NPs) (PtRu alloy partially coated by one-layer MoS2 nanosheets) were prepared through a 'wet chemistry' approach. The obtained NPs were directly embedded, at 5 parts per hundred resin/rubber (phr) loading, in a poly (divinylbenzene-co-vinyl benzyl chloride) hyper-crosslinked (HCL) resin, synthesized via bulk polymerization of the resin precursors, followed by conventional FeCl3 post-crosslinking. The obtained HCL nanocomposites were characterized to evaluate the effect of the NPs. It shows a high degree of crosslinking, a good dispersion of NPs and a surface area up to 1870 ± 20 m2/g. The catalytic activity of the HCL nanocomposite on phenol wet air oxidation was tested at low air pressure (Pair = 0.3 MPa) and temperature (T = 95 °C), and at different phenol concentrations. At the lower phenol concentration, the nanocomposite gives a total organic carbon (TOC) conversion of 97.1%, with a mineralization degree of 96.8%. At higher phenol concentrations, a phenol removal of 99.9%, after 420 min, was achieved, indicating a quasi-complete depletion of phenol, with a TOC conversion of 86.5%, corresponding to a mineralization degree of 84.2%. Catalyst fouling was evaluated, showing good reusability of the obtained nanocomposite.

Self-Suspended Nanoparticles for N-Alkylation Reactions: A New Concept for Catalysis.

The catalytic activity of snowman-like and core-shell Fe3O4/Au nanoparticles (NPs), obtained through a "wet chemistry" approach which directly restitutes nanocatalysts stable and highly active in the reaction medium, was tested towards N-alkylation reactions. The nanocatalysts were tested for the synthesis of secondary amines. The core-shell NPs, thanks to the surface properties, homogeneous dispersion and intimate connection with reagents in the catalyst medium, exhibited an excellent catalytic activity (e. g. >99 % yield and conversion of aniline in very short time and mild conditions). Owing to the magnetic part, the nanoparticles can be easily separated and reused, showing an almost stable activity after 10 cycles.

Active biocatalyst for biodiesel production from spent coffee ground.

Physical adsorption preserving activity and support reusability was used to directly bond lipase from Thermomyces lanuginosus on citric acid (CA) modified Fe3O4/Au magnetic nanoparticles. A new faster approach has been used for CA ligand exchange, which ensures an high payload of stable enzyme. The immobilized lipase was tested for the biodiesel production from spent coffee ground in a solvent free system. It retains, after 60 days, more than 90% of its initial activity. Biodiesel yield of 51.7%, after 3 h of synthesis, which increases up to ∼100% after 24 h indicating an enzymatic fast kinetic, was measured. No significant decrease, during the first three cycles of use, of the lipase activity occurs. The biodiesel presents an ester content of 98.4 ±â€¯0.23 in agreement with the EN14214. The iodine value of 76.67 (g iodine/100 g) is in agreement with the European standard.