Comparison of conventional and severe shot peening effects on the microstructure, texture, roughness, hardness, and electrochemical behavior of austenitic stainless steel.

In the present research, microstructure, texture, roughness, hardness, and electrochemical behavior of AISI 316L austenitic stainless steel before and after shot peening were studied to elucidate the effect of conventional and severe shot peening (CSP and SSP) processes. After the shot peening, the fraction of strain-induced martensite (SIM) and mechanical twins (MTs) in the sub-surface layer was increased. The fraction of SIM and MTs in the SSP sample was higher than in the CSP sample. The XRD patterns indicated that the SSP sample had a higher peak broadening compared to the CSP sample. In the CSP and SSP samples, a gradient microstructure was formed along the depth direction. The microstructure of the topmost layer of the CSP and SSP samples exhibited numerous ultrafine grains. The grain refining during severe shot peening was faster because of the accumulation of more strain. The CSP and SSP samples revealed a gradient distribution of elements. After the SSP, the intensity of ⟨110⟩‖ED fiber texture decreased from 12.7 to 11.6 × R and the average intensity of ⟨100⟩‖ED fiber texture increased from 1.7 to 2.0 × R, respectively, compared to the CSP sample. The surface roughness of the SSP sample (Rq = 73.6 nm and Ra = 45.2 nm) was lower than that of the CSP sample which represented the roughness decreased with surface coverage increasing from 100 % to 1500 %. Also, the wettability increased after the conventional and severe shot peening processes. In addition, the microhardness of the CSP and SSP samples showed a gradient distribution. The CSP sample had the lowest corrosion current density (0.13 µA/cm2) whereas the NP (non-peened) sample exhibited the highest current density (0.65 µA/cm2). The presence of ⟨100⟩-oriented grains in both CSP and SSP samples led to the higher corrosion resistance of shot-peened steels compared to the NP sample. The presence of favorable texture with higher intensity in the CSP sample was responsible for the higher corrosion resistance of the CSP sample compared to the SSP sample. Finally, the gradient distribution of elements along the depth direction in the CSP and SSP steels improved the corrosion resistance of the surface.

Evading the strength-ductility trade-off dilemma in AA2024 alloy by short-term natural re-aging after T351 temper.

In this research, the influence of short-term natural re-aging after T351 temper on the microstructural evolution and mechanical behavior of AA2024 aluminum alloy was investigated. Grain growth occurred in the microstructures of the natural re-aged sample and a large number of Al7Cu2Fe particles were located inside the alpha grains. At the re-aging time of 1440 min, the peaks of XRD were shifted strongly to the right due to the formation of θ'', S″, θ', and S'. The results revealed that the precipitation rate was high in the AA2024 alloy during natural aging. With increasing the re-aging time, texture parameters remained almost unchanged. The hardness increased slowly within the first 60 min, then enhanced rapidly between 60 and 2880 min, and finally became stable at around 139 HV between 2880 and 11520 min. When the natural re-aging time increased from 240 to 2880 min, the strengthening trended speed up, viz, the yield strength increased from 226.6 to 357.3 MPa, and the ultimate tensile strength enhanced from 452.2 to 535.5 MPa. Compared to the as-received sample (T351 temper), the ultimate tensile strength of the re-aged sheet improved from 455.5 to 535.5 MPa, the ductility remained unchanged, and the hardness increased from 128.8 to 138.2 HV, which was owing to the acceleration of the precipitation caused by the presence of high-content Al7Cu2Fe particles in the interior of the alpha-aluminum grains in the natural re-aged sample. It was found that the Portevin-Le Chatelier instability of AA2024 alloy was effectively postponed after natural re-aging. With increasing the natural re-aging time, the strain hardening rate of the AA2024 sheet increased. The strengthening of the natural re-aged sample for 1440 and 2880 min was a result of a synergistic effect of precipitation hardening due to the formation of θ'', S″, θ', and S' phases, elimination of Portevin Le-Chatelier instability, and highly efficient load transfer from alpha-aluminum to Al7Cu2Fe. Finally, to use the A2024 alloy produced by natural re-aging for 1440 or 2880 min, two methods were proposed.

Investigating the relationship between mechanical properties and residual stress in the laser cladding process of Inconel 625 superalloy.

In the present study, the tensile strength, fracture surface, hardness, and amount of residual stress in Inconel 625 super alloy cladded with direct metal deposition (DLD) process in the states before and after stress relief was studied. Residual stresses on the cladding layer surface were determined via XRD method. According to results, the yield strength of Am sample increased by 10% compared to thecast sample (reference sample). Although the yield strength experiebced an increase, the ductility followed an opposite trend falling from 42.5% to 26%. According to residual stress test outcomes, tensile residual stress of 361 MPa in the additive-manufactured sample. After stress relaxation heat treatment and almost complete removal of residual stress, the ductility reached 52.5%, the ultimate strength was also improved by 17% from cast sample. Also, after stress relaxation, the hardness of the sample and its fluctuations are reduced.

Investigation of microstructure, crystallographic texture, and mechanical behavior of magnesium-based nanocomposite fabricated via multi-pass FSP for biomedical applications.

In this work, the microstructure, crystallographic texture, hardness, and tensile behavior of AZ91/HA bio-nano composite manufactured by multi-pass friction stir processing (FSP) were investigated. With increasing the number of FSP passes, the average size of grains is reduced. The processed AZ91 and AZ91/HA nanocomposite after the third pass had the lowest grain size (4.5 and 2.6 µm, respectively). Also, the average grain size of composites was smaller than that of monolithic samples at the same pass number. The results showed that particle distribution in the AZ91/HA nanocomposite is significantly affected by the number of passes. The increment of the pass number led to a more uniform dispersion of HA nanoparticles in the matrix due to more plastic flow of materials. With increasing the pass number to three, the accumulated strain increased to 0.726 (monolithic) and 0.623 (composite) due to repeating mechanical stirring. There was a texture transition ({101‾1} to {0002}) via performing only one pass of FSP. Suppression of grain rotation by HA nanoparticles maintained the intensity of {101‾1} texture as a corrosion-resistant orientation after the third pass. With increasing the pass number of FSP, the hardness and strength of samples increased due to the grain size reduction and the more uniform dispersion of HA powder. The composite sample after the third pass exhibited the highest hardness of 117.0 HV and ultimate tensile strength of 306.6 MPa. The failure mode of processed samples was ductile. There were smaller dimples on the fracture surface of the composite samples due to their lower grain size and also the presence of HA nanoparticles. Considering the obtained results, the nanocomposite after the third pass can be a good load-bearing implant for biomedical applications.

Synergistic effects of hybrid (HA+Ag) particles and friction stir processing in the design of a high-strength magnesium matrix bio-nano composite with an appropriate texture for biomedical applications.

In this work, the effects of hybrid (HA + Ag) particles and triple-pass friction stir processing on the microstructure, texture, hardness, and tensile behavior of magnesium matrix bio-nano composite were investigated. The results showed that the mean grain size of samples was in the range of 1-5 µm owing to the occurrence of dynamic recrystallization and suppression of grain growth by second phase particles. All samples exhibited uniform dispersion of particles in the magnesium matrix caused by triple-pass FSP. However, some agglomerations were visible in the microstructure of AZ91/nHA nanocomposite. The average grain size of the AZ91/nHA/smAg sample (1.4 µm) was smaller than that of the AZ91/nHA/mAg sample (2.1 µm), which was attributed to the formation of higher content of MgxAgy precipitates in the AZ91/nHA/smAg composite. By performing the FSP, the content of Mg17Al12 was significantly decreased due to the dissolution of beta into the alpha caused by the breakup effect of mechanical stirring and temperature increase of samples. The AZ91/nHA/smAg sample had the highest texture parameter for the {101‾1} orientation as the high corrosion resistance texture. This was due to the promoting the non-basal slip caused by the dissolution of smAg particles in the magnesium matrix. After the FSP, the microhardness distribution of AZ91, AZ91/nHA, AZ91/nHA/mAg, and AZ91/nHA/smAg samples tended to be uniform and the average hardness was improved owing to the fragmentation of beta particles, grain refinement, and homogeneous dispersion of second phase particles. Compared with the AZ91/nHA/mAg sample, an increase in ultimate tensile strength (291.7 MPa), and a decrease in total elongation (5.6%) and energy absorption (12.3 J/cm3) were observed in the AZ91/nHA/smAg sample due to the formation of a higher content of the silver-rich precipitates in the AZ91/nHA/smAg sample during cooling caused by the higher solubility of silver submicron particles. The fracture surfaces of all processed samples consisted of a large number of fine equiaxed dimples (ductile fracture) owing to the grain refinement and the presence of fine second phase particles.