Catalytic Ozonation of Reactive Black 5 in Aqueous Solution Using Iron-Loaded Dead Leaf Ash for Wastewater Remediation.

In the current study, iron-loaded dead leaf ash (Fe-DLA) was used as a novel catalyst in the heterogeneous catalytic ozonation process (HCOP) for textile wastewater containing Reactive Black 5 (RB-5). The research demonstrates a significant boost in removal efficiency, reaching 98.76% with 1.0 g/min O3 and 0.5 g/L catalyst dose, by investigating key variables such as pH, ozone and catalyst doses, initial concentration, and the presence of scavengers in 1 L wastewater. The addition of tert-butyl alcohol (TBA) reduced RB-5 elimination, indicating the involvement of OH radicals. Catalyst reusability decreased slightly (2.05% in the second run; 4.35% in the third), which was attributed to iron leaching. A comparison of single ozonation (Fe-DLA) adsorption and catalytic ozonation processes (Fe-DLA/O3) revealed that the combined process improved dye degradation by 25%, with removal rates ranking as Fe-DLA adsorption O3 Fe-DLA/O3, with an impressive 76.44% COD removal. These results strongly support RB-5 removal using Fe-DLA and HCOP at a basic pH, highlighting the catalyst's utility in practical wastewater treatment.

Graphene-grafted bimetallic MOF membranes for hazardous & toxic contaminants treatment.

Development of membrane with improved carbon dioxide (CO2) gas separation capability is a significant challenge. However, the fabrication of membrane that efficiently separate and purification CO2-containing gases has been the focus of global attention. Cellulose Acetate (CA) has robust reinforcing characteristics when incorporated within a suitable polymer matrix. This work focus on the synthesis of novel mixed matrix membranes (MMMs) by introducing Graphene-grafted bimetallic MOFs in Cellulose Acetate polymer. The graphene-grafted bimetallic MOF (GG-BM MOFs) was prepared by a hydrothermal technique. Whereas, the solution casting approach used to fabricate membranes. The 1-5 wt% of GG-BM MOFs incorporated into the CA matrix. The mechanical, hydrophilicity and adsorption characteristics of fabricated MMMs were investigated. The crystallinity of MMM enhanced after the addition of GG-BM MOFs. In addition, the mechanical characteristics of MMMs were improved with the incorporation of GG-BM MOFs inside the polymer matrix. Maximum stress and strain was obtained for 2 wt% MMM (36.4 N/mm2 and 11% respectively). The CO2 adsorption performance was evaluated at 10 bar and 45 °C. The FTIR results represent insignificant bond shifting with the addition GG-BM MOFs at these conditions. The overall results showed that MMMs containing 2 wt% GG-BM MOFs have good adsorption properties for CO2 i.e 3.15 wt% of CO2. The MMMs have shown a decrease in the mechanical properties and CO2 adsorption at the higher GG-BM MOFs loading due to the presence of agglomeration which was confirmed through SEM. Thus, the addition of GG-BM MOFs in the CA matrix positively altered the physicochemical characteristics of the resulting MMMs, which could assist them in achieving remarkable CO2 adsorption at 2 wt%.

A Novel Energy-Efficient Reservation System for Edge Computing in 6G Vehicular Ad Hoc Network.

The roadside unit (RSU) is one of the fundamental components in a vehicular ad hoc network (VANET), where a vehicle communicates in infrastructure mode. The RSU has multiple functions, including the sharing of emergency messages and the updating of vehicles about the traffic situation. Deploying and managing a static RSU (sRSU) requires considerable capital and operating expenditures (CAPEX and OPEX), leading to RSUs that are sparsely distributed, continuous handovers amongst RSUs, and, more importantly, frequent RSU interruptions. At present, researchers remain focused on multiple parameters in the sRSU to improve the vehicle-to-infrastructure (V2I) communication; however, in this research, the mobile RSU (mRSU), an emerging concept for sixth-generation (6G) edge computing vehicular ad hoc networks (VANETs), is proposed to improve the connectivity and efficiency of communication among V2I. In addition to this, the mRSU can serve as a computing resource for edge computing applications. This paper proposes a novel energy-efficient reservation technique for edge computing in 6G VANETs that provides an energy-efficient, reservation-based, cost-effective solution by introducing the concept of the mRSU. The simulation outcomes demonstrate that the mRSU exhibits superior performance compared to the sRSU in multiple aspects. The mRSU surpasses the sRSU with a packet delivery ratio improvement of 7.7%, a throughput increase of 5.1%, a reduction in end-to-end delay by 4.4%, and a decrease in hop count by 8.7%. The results are generated across diverse propagation models, employing realistic urban scenarios with varying packet sizes and numbers of vehicles. However, it is important to note that the enhanced performance parameters and improved connectivity with more nodes lead to a significant increase in energy consumption by 2%.

Factors leading to delayed and challenging presentation of benign breast lumps in young females.

Background and Objective: A delayed presentation of benign breast diseases may lead to a therapeutic challenge when they enlarge enormously or become multiple. Aim of this study was to evaluate the factors leading to delayed presentation of benign breast lumps. Methods: This cross-sectional study was conducted at Madinah Teaching Hospital and Allied Hospital, Faisalabad from January 2019 to October 2021. One hundred and forty five female patients were selected by non-probability purposive sampling. Patients with large size (>5cm) or multiple benign breast lumps were included. An interview was conducted using structured questionnaire translated in Urdu. Factors leading to delayed presentation and social impact scale for stigma were evaluated. Results: Patients had a mean age of 26.52 ± 6.90 years. The average delay of seeking medical care was 8.48 ± 8.41 months. Factors leading to delayed presentation were; lack of knowledge n=112 (77.2%) and parda (religious issues) n=112 (77.2%), followed by poverty n=109 (75.2%), and fear of cancer n=90 (62.1%). All the sub-scales of stigma, i.e., social rejection, financial insecurity, internalized shame and social isolation were high in late presenters, though, only financial insecurity was significantly high in late presenters (p=0.03). Conclusion: Lack of awareness, socioeconomic factors and disease related stigma were the main factors related to delayed presentation in young females with benign breast diseases. Addressing these factors may improve timely diagnosis and management of delayed and challenging cases.

Catalytic ozonation for the removal of reactive black 5 (RB-5) dye using zeolites modified with CuMn2O4/gC3N4 in a synergic electro flocculation-catalytic ozonation process.

This study aims to investigate the decolourization efficiency of reactive black 5 (RB-5) dye by using CuMn2O4/gC3N4 coated zeolites (zeolite 4A) for the first time in a hybrid electro-flocculation-catalytic ozonation process. A comparison between various treatment options such as electro-flocculation, electro-flocculation in the presence of a catalyst, and catalytic ozonation in combination with electro-flocculation was explored. Moreover, the effect of different factors such as pH, time, catalyst dose, ozone dose, radical scavenger, and voltage has been studied in each treatment option mentioned earlier. The results indicated that the best treatment option was found to be catalytic ozonation in combination with electro-flocculation with removal efficiency (RE) of 90.31% at pH 10 after 30 min of the treatment process. The hydroxyl radical scavenger effect indicated that the synergistic catalytic process follows a radical mechanism. It is therefore concluded that CuMn2O4/gC3N4-zeolite catalysts in synergic electro-flocculation-catalytic ozonation process may be effectively used for the treatment of textile wastewaters.

A study on the influence of pH changes during catalytic ozonation process on alumina, zeolites and activated carbons for the decolorization of Reactive Red-241.

The current study focuses on a prime effect of pH changes in the catalytic ozonation process (COP) by using three main classes of catalysts such as zeolites (alumina-silicates), alumina (metal oxides), and activated carbons for decolorization of Reactive Red 241 (RR-241). The role of pH changes, point of zero charges and the effect of catalyst dose on pH change was studied. The results reveal that the overall removal efficiency of RR-241 in the case of COPs was the highest compared with single ozonation process (at pH = 7 the efficiency was 80, 65 65.5 and 60% for AC/O3, Al2O3/O3, Zeolite/O3 and O3 respectively). At initial acidic pH 4, the highest pH variations in COPs and ozonation processes were observed. Moreover, the pH changes were not found to be significant near the point of zero charges of materials (pHpzc = 6.8, 8.4 and 8.8 for zeolite, activated carbons and Al2O3, respectively. The COP in the presence of activated carbon shows the highest removal efficiency (82%) at pH 7. The material dose effect indicates that increasing the amount of catalyst (from 1 gm to 2 gm) significantly leads to a change in the pH of the solution. Results reveal the prominent effect and significance of pH changes on the efficiency of COP to determine true catalytic efficiency.

Removal of toluene as a toxic VOC from methane gas using a non-thermal plasma dielectric barrier discharge reactor.

Methane is the main component of biogas, which could be used as a renewable energy source for electricity, source of heat, and biofuel production after upgrading from biogas. It also contains toxic compounds which cause environmental and human health problems. Therefore, in this work, the removal of a toxic compound (toluene) from methane gas was studied using a dielectric barrier discharge (DBD) reactor. It was observed that the removal of the toxic compound could be achieved from methane carrier gas using a dielectric barrier discharge reactor, and it depends on plasma input power. The maximum removal of the toxic compound was 85.9% at 40 W and 2.86 s. The major gaseous products were H2 and lower hydrocarbons (LHC) and the yield of these products also increases with input power. In the current study, the yield of gaseous products depends on the decomposition of toxic compounds and methane, because the decomposition of methane also produces H2 and lower hydrocarbons. The percentage yield of H2 increases from 0.43-4.74%. Similarly, the yield of LHC increases from 0.56-7.54% under the same reaction conditions. Hence, input power promoted the decomposition of the toxic compound and enhanced the yield of gaseous products.

Elimination of basic blue 9 by electrocoagulation coupled with pelletized natural dead leaves (Sapindus mukorossi) biosorption.

Elimination of basic blue 9 (BB-9), a cationic textile dye, by electrocoagulation coupled with biosorption exploiting pelletized natural dead leaves (PNDL) of Sapindus mukorossi, an economic alternative biosorbent, was investigated. The experimental runs were conducted in a laboratory-scale hybrid reactor loaded with Al electrodes, aeration spargers and PNDL packed twin suspended buckets. The pelletized adsorbents offer key advantages of good mechanical stability, lesser clogging risk, and easy disengagement as compared to powdered adsorbents. The parameters of current density, pH, PNDL dose, and initial dye concentration were studied for the decolorization and COD removal efficiency. The experimental results revealed that up to 99.9% decolorization and 90.01% COD removal efficiency achieved after 8 min at optimum condition of current density (j)=20.27 mA/cm2, pH = 9, PNDL dose = 6 g/L, and initial dye concentration = 50 mg/L. The BB-9 elimination followed the first-order kinetics with K1=0.318 min-1 and R2=0.997. The results revealed the potential of PNDL as a feasible biosorbent with the effective performance of the coupled process.

Treatment of leachate through constructed wetlands using Typha angustifolia in combination with catalytic ozonation on Fe-zeolite A.

Leachate control and management is a major challenge faced during solid waste management as it may pollute surface and groundwaters. In the current research, constructed wetlands (CWs) vegetated with Typha angustifolia plant in combination with catalytic ozonation by ferrous (Fe)-coated zeolite A was studied for the treatment of leachate. The CWs treatment with 9 days detention reduced the chemical oxygen demand (COD) and biochemical oxygen demand (BOD) up to 75.81% and 69.84%, respectively. Moreover, total suspended solids (TSS), total dissolved solids (TDS), and total kjeldahl nitrogen (TKN) removal of 91.16%, 33.33%, and 25.22% were achieved, respectively. The Fe-coated zeolite A catalytic ozonation further reduced the COD up to 90.7%. Comparison of the processes showed the effective performance of the combined process (CW/O3/Fe-zeolite) with 97.76% COD reduction of leachate. It is, therefore, concluded that the studied combined process (CW/O3/Fe-zeolite A) was more efficient as compared with single ozonation and CW alone, hence it can be implied for the leachate treatment in real conditions.

Degradation of safranin by heterogeneous Fenton processes using peanut shell ash based catalyst.

Today, dyes are one of the major problematic pollutants in the environment and are broadly used in several industrial sectors. In the current research work, decolorization of safranin (basic dye) from aqueous solution was investigated using iron-impregnated peanut shell ash (Fe-PSA) as a catalyst in the UV-assisted heterogeneous Fenton process (Fe-PSA/H2O2/UV). The effect of parameters such as H2O2 concentration, catalyst dose, pH, initial dye concentration, temperature, and agitation speed was studied. The maximum decolorization of safranin was achieved at optimum parametric values of reagent dose = 8 mM, catalyst dose = 0.5 g, pH = 3, initial concentration of safranin = 50 ppm, temperature = 25 °C, and agitation speed = 200 rpm. The results revealed the efficient performance of Fe-PSA as catalyst in the Fe-PSA/H2O2/UV process for safranin treatment.

Knowledge of Medical Practitioners about Periodontal Diseases and Its Impact on Overall Health: A Cross-sectional Study.

INTRODUCTION: Periodontal disease is defined as an inflammation of the gums that may result in loss of the tissues holding the teeth in its place. The signs and symptoms include red and/or swollen gums, bleeding gums, halitosis or in severe cases, loosening of teeth. Periodontal diseases act as a risk factor for several health conditions including diabetes and cardiovascular diseases and it can even result in adverse pregnancy outcomes. Therefore, in this study, we aim to assess the knowledge of medical practitioners regarding periodontal diseases and its impact on overall health. METHODS: We conducted a cross-sectional, questionnaire-based study that included 100 medical practitioners working in the Combined Military Hospital Lahore, Pakistan. RESULTS: In our study, 83.0% participants knew the definition of periodontal disease; 7.0% of the participants responded that they take their patient's periodontal history; 26.0% screened their patients for gums related problems while 87.0% reported that they are comfortable in performing an oral examination. 80.0% of the participants agreed that periodontal disease can be a risk factor for diabetes; 73.0% said they believe that it can lead to adverse pregnancy outcomes; 62.0% thought that it can result in cardiovascular diseases. CONCLUSION: Most of the participants in our study had a considerable amount of knowledge about periodontal diseases. However, it is important to stress the value of taking a detailed periodontal history and screening patients for periodontal problems.

Heritability of carotid intima-media thickness: a twin study.

OBJECTIVE: To estimate the heritability of carotid intima-media thickness (IMT), a surrogate marker for atherosclerosis, independent of traditional coronary risk factors. METHODS AND RESULTS: We performed a classical twin study of carotid IMT using 98 middle-aged male twin pairs, 58 monozygotic (MZ) and 40 dizygotic (DZ) pairs, from the Vietnam Era Twin Registry. All twins were free of overt cardiovascular disease. Carotid IMT was measured by ultrasound. Bivariate and multivariate analyses were used to determine the association between traditional cardiovascular risk factors and carotid IMT. Intraclass correlation coefficients and genetic modeling techniques were used to determine the relative contributions of genes and environment to the variation in carotid IMT. In our sample, the mean of the maximum carotid IMT was 0.75+/-0.11. Age, systolic blood pressure and HDL were significantly associated with carotid IMT. The intraclass correlation coefficient for carotid IMT was larger in MZ (0.66; 95% confidence interval [CI], 0.62-0.69) than in DZ twins (0.37; 95% CI, 0.29-0.44), and the unadjusted heritability was 0.69 (95% CI, 0.54-0.79). After adjusting for traditional coronary risk factors, the heritability of carotid IMT was slightly reduced but still of considerable magnitude (0.59; 95% CI, 0.39-0.73). CONCLUSION: Genetic factors have a substantial influence on the variation of carotid IMT. Most of this genetic effect occurs through pathways independent of traditional coronary risk factors.