Pedestrian Safety in Frontal Tram Collision, Part 1: Historical Overview and Experimental-Data-Based Biomechanical Study of Head Clashing in Frontal and Side Impacts.

This article represents the first paper in a two-part series dealing with safety during tram-pedestrian collisions. This research is dedicated to the safety of trams for pedestrians during collisions and is motivated by the increased number of lethal cases. The first part of this paper includes an overview of tram face development from the earliest designs to the current ones in use and, at the same time, provides a synopsis and explanation of the technical context, including a link to current and forthcoming legislation. The historical design development can be characterised by three steps, from an almost vertical front face, to leaned and pointed shapes, to the current inclined low-edged windshield without a protruding coupler. However, since most major manufacturers now export their products worldwide and customisation is only of a technically insignificant nature, our conclusions are generalisable (supported by the example of Berlin). The most advantageous shape of the tram's front, minimising the effects on pedestrians in all collision phases, has evolved rather spontaneously and was unprompted, and it is now being built into the European Commission regulations. The goal of the second part of this paper is to conduct a series of tram-pedestrian collisions with a focus on the frontal and side impacts using a crash test dummy (anthropomorphic test device-ATD). Four tram types approaching the collision at four different impact speeds (5 km/h, 10 km/h, 15 km/h, and 20 km/h) were used. The primary outcome variable was the resultant head acceleration. The risk and severity of possible head injuries were assessed using the head injury criterion (HIC15) and its linkage to the injury level on the Abbreviated Injury Scale (AIS). The results showed increasing head impacts with an increasing speed for all tram types and collision scenarios. Higher values of head acceleration were reached during the frontal impact (17-124 g) compared to the side one (2-84 g). The HIC15 values did not exceed the value of 300 for any experimental setting, and the probability of AIS4+ injuries did not exceed 10%. The outcomes of tram-pedestrian collisions can be influenced by the ATD's position and orientation, the impact speed and front-end design of trams, and the site of initial contact.

Pedestrian Safety in Frontal Tram Collision, Part 2: Laminated Glass as a Crucial Part of the Absorption and Deformation Zone-Its Impact Test and Analysis.

As was shown in the previous part of the study, windshields are an important part of the passive safety means of modern low-floor trams with an extraordinary effect on pedestrian safety in a pedestrian-tram collisions. Therefore, maximum attention must be paid to the definition of tram windshield characteristics. This article describes a windshield crash test, from which data are obtained to verify the feasibility of the applied computational approaches. A developed analytical model is utilised for a simple description of the energy balance during collision with an illustrative definition of the important parameters of laminated glass as well as their clear physical interpretations. The finite element analysis (FEA) performed in Ansys software using two versions of material definition, namely a simpler (*MAT_ELASTIC with nonlocal failure criterion) and a more complex (*MAT_GLASS with brittle stress-state-dependent failure) material model, which are presented as suitable for obtaining a detailed description of the shattering process of laminated glass, which can also be used effectively in windshield engineering.

Intervertebral (lumbar) disc replacement:the current state and future perspectives.

PURPOSE: Low back pain is a significant socio-economic problem which is expected to deepen. Degenerative disc disease is considered to be one of its main causes. Unsuccessful conservative treatments usually lead to surgical treatments, including methods providing pain relief by vertebral fusion in the affected segment. However, this leads to changes in biomechanics, which is why approximately 30 years ago total disc replacements appeared. This work aims at determining the current state of treatments with this kind of replacement, comparing the results with those of fusion methods and assessing why fusion continues to dominate. Current treatments of degenerative disc disease by advanced procedures (regenerative and gene therapy, 3D printing) is also examined and evaluated, and future developments are considered. METHODS: A critical review based on available scientific articles from online databases. The main keywords used were "lumbar", "total", "disc" and "replacement", supplemented according to the individual, monitored areas ("follow-up", "fusion", "future" etc.). For the articles found through database search (n = 895), narrower selection was made and the result was 33 articles included in review. REVIEW: Total disc replacements have not yet satisfactorily demonstrated that they are superior to fusion methods in long term follow-up. Advanced methods are in their infancy. CONCLUSIONS: Additional research and development of total disc replacements is still necessary. For implants, the 3D scan - 3D model - 3D printing chain and its related technologies are increasingly important. The development of regenerative procedures using induced pluripotent stem cells and gene therapies is important, but conservative treatments and primary prevention should also be developed because regenerative procedures and gene therapies apparently will not be used routinely until the future.

Objective Methods of Muscle Tone Diagnosis and Their Application-A Critical Review.

"Muscle tone" is a clinically important and widely used term and palpation is a crucial skill for its diagnosis. However, the term is defined rather vaguely, and palpation is not measurable objectively. Therefore, several methods have been developed to measure muscle tone objectively, in terms of biomechanical properties of the muscle. This article aims to summarize these approaches. Through database searches, we identified those studies related to objective muscle tone measurement in vivo, in situ. Based on them, we described existing methods and devices and compared their reliability. Furthermore, we presented an extensive list of the use of these methods in different fields of research. Although it is believed by some authors that palpation cannot be replaced by a mechanical device, several methods have already proved their utility in muscle biomechanical property diagnosis. There appear to be two issues preventing wider usage of these objective methods in clinical practice. Firstly, a high variability of their reliability, and secondly, a lack of valid mathematical models that would provide the observed mechanical characteristics with a clear physical significance and allow the results to be compared with each other.

Low Concentrated Fractionalized Nanofibers as Suitable Fillers for Optimization of Structural-Functional Parameters of Dead Space Gel Implants after Rectal Extirpation.

Dead space after rectal resection in colorectal surgery is an area with a high risk of complications. In this study, our goal was to develop a novel 3D implant based on composite hydrogels enriched with fractionalized nanofibers. We employed, as a novel approach in abdominal surgery, the application of agarose gels functionalized with fractionalized nanofibers on pieces dozens of microns large with a well-preserved nano-substructure. This retained excellent cell accommodation and proliferation, while nanofiber structures in separated islets allowed cells a free migration throughout the gel. We found these low-concentrated fractionalized nanofibers to be a good tool for structural and biomechanical optimization of the 3D hydrogel implants. In addition, this nano-structuralized system can serve as a convenient drug delivery system for a controlled release of encapsulated bioactive substances from the nanofiber core. Thus, we present novel 3D nanofiber-based gels for controlled release, with a possibility to modify both their biomechanical properties and drug release intended for 3D lesions healing after a rectal extirpation, hysterectomy, or pelvic exenteration.

Selected biomechanical aspects of the asymmetrical loading of the human postural system when riding the C1 speed canoe and their influence on the development of muscular imbalances.

OBJECTIVES: The main aim of this study was to analyse selected biomechanical aspects of the asymmetrical loading of the human postural system when riding the C1 speed canoe and their influence on the development of muscular imbalances. METHODS: 3D kinematic analysis of a simulated forward stroke of the canoeist in a pool with a counter-current (N = 9) and analysis of MRI data with selected individuals (N = 5), videoanalysis of actual paddling top athletes (N = 12), the kinesiological analysis of movement. RESULTS: Can be stated that when riding a C1 speed canoe the postural system is exposed to two types of asymmetric loading. In the first place, there is lateral asymmetry, which stems from the very nature of the one-sided paddling on this type of vessel. The canoeist has to compensate for the consequent instability by shifting the body's centre of gravity higher above the kneeling lower limb. This effect is achieved by the so-called pelvic lateralisation from the paddling side and by this side's skewing to the kneeling lower limb. Another asymmetry is connected to the forward-backward body movement and its time-dependent deviation from the neutral posture. A significant disproportion between generally fixation movements of the lower part of the body and phasic movements of the upper part of the body has been confirmed. These asymmetrical positions result in a significant unilateral overloading of the quadratus lumborum on the side of the supporting lower limb (side without the paddle), as well as an overloading of the spine straighteners in the lumbar area, in particular on the part of a supporting lower limb, and bilateral yet asymmetric overloading of m. iliopsoas, which in addition takes place in different isometries. The analysis of MRI data indicates that, during longitudinal training, lateral disproportion in the volume and intensity of postural system loading is the cause of different cross sections of the iliopsoas muscle and quadratus lumborum muscle on the side of the kneeling and supporting lower limbs. With both muscles, larger cross sections with a statistical significance level α = 0.05 and thus also strength on the side of the supporting lower limb can be expected. CONCLUSION: When canoeing on the C1, a significant unilateral overloading occurs with m. quadratus lumborum on the part of the supporting lower limb (side without paddle). Furthermore, spine straighteners in the lumbar area are overloaded, in particular in the part of the supporting lower limb. Last but not least however, the bilateral asymmetric overloading of m. iliopsoas occurs.

Peripartum rupture of renal artery aneurysm - case report.

We present a case of silent rupture of the renal artery aneurysm in a pregnant woman brought to the maternity hospital in shock. Renal artery aneurysms (RAA) are rare and account for 0.01-0.5% of all aneurysms with an incidence of approximately 0.09%. Rupture of the renal artery aneurysm is a rare and severe complication associated with extremely high morbidity and mortality in both mother and fetus. Thanks to the improvement and effectiveness of medical care in the 21st century, fetal mortality decreased by 70-80%, and 60-70 % for the mother. The essence of a successful management of this serious, life-threatening condition is a close cooperation between obstetricians, midwives, anesthesiologists, general surgeons, and vascular surgeons.

Load Measurement of the Cervical Vertebra C7 and the Head of Passengers of a Car While Driving across Uneven Terrain.

The article deals with the measurement of dynamic effects that are transmitted to the driver (passenger) when driving in a car over obstacles. The measurements were performed in a real environment on a defined track at different driving speeds and different distributions of obstacles on the road. The reaction of the human organism, respectively the load of the cervical vertebrae and the heads of the driver and passenger, was measured. Experimental measurements were performed for different variants of driving conditions on a 28-year-old and healthy man. The measurement's main objective was to determine the acceleration values of the seats in the vehicle in the vertical movement of parts of the vehicle cabin and to determine the dynamic effects that are transmitted to the driver and passenger in a car when driving over obstacles. The measurements were performed in a real environment on a defined track at various driving speeds and diverse distributions of obstacles on the road. The acceleration values on the vehicle's axles and the structure of the driver's and front passenger's seats, under the buttocks, at the top of the head (Vertex Parietal Bone) and the C7 cervical vertebra (Vertebra Cervicales), were measured. The result of the experiment was to determine the maximum magnitudes of acceleration in the vertical direction on the body of the driver and the passenger of the vehicle when passing a passenger vehicle over obstacles. The analysis of the experiment's results is the basis for determining the future direction of the research.

Poly-ε-caprolactone and polyvinyl alcohol electrospun wound dressings: adhesion properties and wound management of skin defects in rabbits.

Aim: This study evaluates the effect of electrospun dressings in critical sized full-thickness skin defects in rabbits. Materials & methods: Electrospun poly-ε-caprolactone (PCL) and polyvinyl alcohol (PVA) nanofibers were tested in vitro and in vivo. Results: The PCL scaffold supported the proliferation of mesenchymal stem cells, fibroblasts and keratinocytes. The PVA scaffold showed significant swelling, high elongation capacity, limited protein adsorption and stimulation of cells. Nanofibrous dressings improved wound healing compared with the control group in vivo. A change of the PCL dressing every 7 days resulted in a decreased epithelial thickness and type I collagen level in the adhesive group, indicating peeling off of the newly formed tissue. In the PVA dressings, the exchange did not affect healing. Conclusion: The results demonstrate the importance of proper dressing exchange.

In vivo assessment of time dependent changes of T2* in medial meniscus under loading at 3T: A preliminary study.

Due to the internal structure of the knee joint, the ability to characterize and quantify the dynamic response of the meniscal tissue directly in vivo is highly problematic. The main purpose of this study was to investigate the behaviour of the meniscus under loading conditions. Four healthy young females were included. To obtain T2* values in the meniscus, the vTE sequence was used with 10 echoes ranging from 0.8 to 10.1 ms. Submilisecond first echo time is a great advantage of vTE sequence allowing for precise mapping of relatively short T2*. The two-parametric least squares fitting procedure was used to calculate T2* pixel-wise. A custom-made diamagnetic apparatus was developed to simulate stress conditions on the lower limb in a conventional MR scanner. vTE T2* was performed in five consecutive scans, 6:10 min apart. Three different compartments of the medial and lateral meniscus were segmented. The differences at the different time-points were calculated. A constant increase of T2* times after compression was statistically significant in the anterior horn of the medial meniscus. T2* mapping with variable echo time sequence might be a satisfactorily sensitive technique to detect the changes of meniscus physiology under loading conditions in vivo.

Physiological responses to different neuromuscular movement task during eccentric bench press.

OBJECTIVES: Increasing muscular hypertrophy is one of the main reasons for participating in a resistance training program, where different movement task such as eccentric cadences may serve as a potent hypertrophic stimulus and improve movement stability. Aim of this study was to investigate the physiological responses between slow 6/0/2/0 (SLOW) and moderate 2/0/2/0 (REG) eccentric cadences during five sets of bench press to failure using 70% 1 repetition maximum (1RM). MATERIALS AND METHODS: Blood samples from sixteen men (21-29y, 85.9±7.7kg, 130±17.5kg bench press 1RM) with at least five years of resistance training experience were taken before, immediately after, 30 min after, and 60 min after both protocols in a randomized cross over study design. RESULTS: ANOVA showed that more repetitions were performed during each set in REG and for the entire REG protocol (p<0.001), but total time under tension was greater during SLOW in each set and for the entire protocol (p<0.001). The post-exercise levels of lactate (p=0.02), creatine kinase (p=0.04), and testosterone (p=0.01) were greater after SLOW. Post-exercise cortisol levels decreased in both protocols (p<0.001), but these decreases were not significantly different between protocols. CONCLUSIONS: Therefore, intentionally slow eccentric speeds and increased eccentric time under tension seem to be effective for increasing acute hormonal responses after exercise. As such, although a SLOW tempo may decrease the amount of total work (i.e. fewer repetitions with the same load), the increased time under tension seems to drive hormonal responses and neurological response, which may play a large role in stimulating muscle growth, coordination and movement stability.

Possibilities of objective identification of meniscoids in joint blocks of the axial system, by MRI and Transfer Vibration through the Spine.

OBJECTIVE: The aim of the study was to identify the meniscoids of the cervical spine using in-vivo MRI imaging and to determine their potential role in the development of functional joint blocks of the axial system (AS). Another objective was to find out how the articular blocks affect the rheological properties of the spine by the Transfer Vibration through the Spine (TVS) method. METHOD: In this study were used methods TVS and MRI. The study was conducted on a research file of 12 subjects and was conceived as a pilot one. RESULTS: It has been shown that the MRI method, in appropriate circumstances, enables the detection of changes in the size and shape of meniscoids in-vivo. On the basis of the investigations carried out, it can be assumed that several mechanisms are involved in the formation of functional joint blocks, and are not primarily caused by the incarceration of meniscoidal tissue. Using the TVS method, it has also been found that a functional articular blockade affects the rheological properties of the axial system, specifically reducing the damping capabilities of the particular spine segment. CONCLUSION: In the follow-up studies, it will be necessary to verify the theoretical interpretations on a larger statistical set.

Calcaneal Tendon Collagen Fiber Morphometry and Aging.

Fibrillar collagen in tendons and its natural development in rabbits are discussed in this paper. Achilles tendons from newborn (~7 days) to elderly (~38 months) rabbits were monitored in intact (n tendons=24) and microtome sectioned (n tendons=11) states with label-free second harmonic generation microscopy. After sectioning, the collagen fiber pattern was irregular for the younger animals and remained oriented parallel to the load axis of the tendon for the older animals. In contrast, the collagen fiber pattern in the intact samples followed the load axis for all the age groups. However, there was a significant difference in the tendon crimp pattern appearance between the age groups. The crimp amplitude (A) and wavelength (Λ) started at very low values (A=2.0±0.6 µm, Λ=19±4 µm) for the newborn animals. Both parameters increased for the sexually mature animals (>5 months old). When the animals were fully mature the amplitude decreased but the wavelength kept increasing. The results revealed that the microtome sectioning artifacts depend on the age of animals and that the collagen crimp pattern reflects the physical growth and development.

Selected mechanical paremeters of women's hair in the Caucasian population.

OBJECTIVE: More parameters have been used for more detailed description of mechanical properties of human hair as a fibre than in analogous studies. All measured samples were taken from five different locations on the heads of 60 women of varied age. METHODS: For each hair, the diameter was determined optically and then the test in the Deform Type 2 testing machine was carried out. Deformation curves were obtained by testing 10 mm long samples up to the rupture point at constant temperature, humidity and constant crossbar speed of 2 mm/min. The curves were processed with software for the calculation of mechanical parameters of the hairs. This specialized software has been designed by us for that purpose. Resulting values were arranged into tables and figures. RESULTS: As far as hair cross-section is concerned, it has been found that for the European population it appears to be rather higher - 86 µm - than indicated in formerly published texts. The 56 µm mentioned in the work of other authors has been observed only utterly exceptionally, in 0.3 % of the population. All quantities studied (except extensibility) display moderate to strong positive skewness in comparison to Gauss distribution. The most marked skewness is seen in the resilience. At the same time, this quantity displays the highest value of non-Gaussian distribution. The elasticity module of 2.3±0.6 GPa is three times lower than the one reported by other authors, yet according to the fact published in our work - which shows unambiguously that the thinner the hair, the higher elasticity module it displays - the value of 7.2 GPa for the 56 µm thick hairs is comparable and it confirms the hypothesis that the cortex, which is responsible for the mechanical strength of the hair, is contained in a higher ratio in thinner hairs. This similarly applies to the ultimate strength; the linearity limit is hard to compare with literature, as it almost does not appear there. CONCLUSION: By measuring 886 samples from the heads of 60 adult women of European type, it was possible to ascertain the current norm for a larger number of mechanical parameters of the hairs. Further merit of this work is the fact that the hairs were taken systematically from five well-defined places of the studied heads in equal count, which is an aspect formerly published works do not respect and they do not present the location of sampling.

Valve interstitial cell culture: Production of mature type I collagen and precise detection.

Collagen often acts as an extracellular and intracellular marker for in vitro experiments, and its quality defines tissue constructs. To validate collagen detection techniques, cardiac valve interstitial cells were isolated from pigs and cultured under two different conditions; with and without ascorbic acid. The culture with ascorbic acid reached higher cell growth and collagen deposition, although the expression levels of collagen gene stayed similar to the culture without ascorbic acid. The fluorescent microscopy was positive for collagen fibers in both the cultures. Visualization of only extracellular collagen returned a higher correlation coefficient when comparing the immunolabeling and second harmonic generation microscopy images in the culture with ascorbic acid. Lastly, it was proved that the hydroxyproline strongly contributes to the second-order susceptibility tensor of collagen molecules, and therefore the second harmonic generation signal is impaired in the culture without ascorbic acid.

Evaluation of rheological parameters of the axial system using the Transfer Vibration through Spine (TVS) method.

OBJECTIVE: The human motion system reacts to both hypo and hyperactivity loads by changes to the rheological properties of tissues. This study deals with changes to the axial system (AS) compartment. Using the appropriate methodologies and mathematical-physical methods, these changes can be identified and quantified. METHODS: This study describes the noninvasive TVS (Transfer Vibration through Spine) method, which was applied to assess the AS selected mechanical properties in various modes. A pilot study was conducted on a top-level twelve-year-old girl-gymnast. The data detection was carried out in three cycles, before and after a peak 3.5 hour training session and the next day, after resting, just before the next training. RESULTS: Specifically, the values of selected rheological parameters, the AS damping coefficient b and viscosity µ, were obtained. The dynamics of their changes, in the stated load cycles, has also been shown. The damping coefficient b fell from the value of 0.626 to 0.324 before training and increased to 0.394 after resting. The viscosity coefficient µ showed a similar trend, namely falling from the value of 9.85 [Pa.s] to 2.15 [Pa.s] and then increasing to 3.8 [Pa.s] . CONCLUSIONS: With its computational solution, the TVS method,is a diagnostic apparatus making it possible to classify AS properties, both quantitatively and qualitatively, or its chosen segments and their changes, respectively. It can be used in classifying, preventing and treating the consequences of extreme motion and relaxing modes. The TVS application also makes it possible to control AS states over therapeutic, recovery, ergonomic and other loading modes of the human locomotion system.

Effect of repeated therapeutic horse riding sessions on the trunk movement of the rider.

OBJECTIVE: To assess the rider's movement during walking the horse in repeated therapeutic horse riding sessions and to determine the relationship between movements of the horse's back and the rider's trunk. METHOD: A total of 12 healthy females (age: 23.3±2.8 years; height: 167.3±4.2 cm; weight: 59.2±5.3 kg) participated in 10 therapeutic horse riding sessions. Two English Thoroughbreds with similar body constitution (aged 19 and 14 years) were used in the experiment. Nine markers were placed on the rider's body and the horse's back, and four video cameras with a 25 Hz frequency were used. Collected data were processed with APAS software. RESULTS: The mediolateral displacements of C7, Th12, and L5 were gradually decreasing in each of the first three sessions. Statistically significant differences (p<0.05) were found between individual sessions in the displacement of C7, Th12 and L5 in the mediolateral and vertical directions as well as in the shoulder and pelvic lateral tilt and rotation. These differences did not show any general tendencies regarding the riders' increasing experiences with riding. The relationships between the displacement of C7, Th12, and L5 and the sacral tuber on the horse's back in the vertical direction were statistically significant (p<0.01) during all sessions. CONCLUSIONS: The displacement of C7, Th12 and L5 in the mediolateral direction decreased during riding sessions. A significant relationship was found between the vertical movement of the horse's back and the rider's trunk. These relationships differed between the horses.

The role of lateral preference of lower limbs in a postural stabilization task.

OBJECTIVE: Postural control is a complex skill based on the interaction of dynamic sensorimotor processes. This study assessed the effect of lateral perturbations on postural re-stabilization regarding lower limb preference. METHODS: A group of 14 physically active individuals (9 male, 5 female) randomly underwent postural perturbations in lateral-left and lateral-right directions at a velocity of 0.2 m.s-1 and a platform shift of 6 cm. Perturbation to the preferred limb side (PS) was noted when the contralateral body movement was primarily controlled by the preferred limb and perturbation to the non-preferred limb side (NS) was noted when the contralateral body movement was primarily controlled by the non-preferred (stabilizing) limb. Prior to, during and after the perturbation centre of pressure (CoP) was registered using a computerized motor driven FiTRO Dynamic Posturography System based on force plate (Fitro Sway Check) with a sampling rate of 100 Hz. The basic stabilographic parameters of peak displacement (Peak 1), peak-to-peak displacement (Peak 2), time to peak displacement (Time 1), time to peak-to-peak displacement (Time 2) and re-stabilization time (Time 3) were analyzed. RESULTS: Results showed significantly larger Time 3 on PS than on NS (2.81 ± 1.32 s and 1.73 ± 1.10 s; p=0.02). However, there were no significant differences in other parameters between PS and NS. CONCLUSION: It may be concluded that the observed shorter re-stabilization time at NS was due to the stabilization role of the non-preferred limb.

Executions and scientific anatomy.

The very word "anatomy" tells us about this branch's connection with dissection. Studies of anatomy have taken place for approximately 2.300 years already. Anatomy's birthplace lies in Greece and Egypt. Knowledge in this specific field of science was necessary during surgical procedures in ophthalmology and obstetrics. Embalming took place without public disapproval just like autopsies and manipulation with relics. Thus, anatomical dissection became part of later forensic sciences. Anatomical studies on humans themselves, which needed to be compared with the knowledge gained through studying procedures performed on animals, elicited public disapprobation and prohibition. When faced with a shortage of cadavers, anatomists resorted to obtaining bodies of the executed and suicide victims - since torture, public display of the mutilated body, (including anatomical autopsy), were perceived as an intensification of the death penalty. Decapitation and hanging were the main execution methods meted out for death sentences. Anatomists preferred intact bodies for dissection; hence, convicts could thus avoid torture. This paper lists examples of how this process was resolved. It concerns the manners of killing, vivisection on people in the antiquity and middle-ages, experiments before the execution and after, vivifying from seeming death, experiments with galvanizing electricity on fresh cadavers, evaluating of sensibility after guillotine execution, and making perfect anatomical preparations and publications during Nazism from fresh bodies of the executed.

Changes in the mechanical parameters of hair in a group of women in reproductive age.

OBJECTIVE: Hair quality and scalp characteristics are considered to be a significant marker of health. This marker is reflected in mechanical properties of hair. To investigate these properties, hair samples have been collected among women of different age and then analyzed. The thickness, Young's modulus of elasticity and ultimate strength limit were the main observed parameters. METHODS: The diameter of each hair has been measured using an optical microscope equipped with a digital camera. The hair was then clipped into the uniaxial tensile testing device. Each sample has been stretched to failure at a speed of 2 mm/min and force vs. elongation was recorded. The mechanical results were converted with respect to the diameter and Stress-Strain curve was obtained for each sample. In addition, all the analyzed samples were divided into two groups in dependence on the age, namely samples from women younger than 35 and over 35 years of age. All the measured parameters were statistically evaluated. RESULTS: Young's modulus, yield and elongation parameters showed no significant difference among samples. On the other hand there was a significant difference among the samples in ultimate strength values. Findings from group analysis showed that women under 35 years show about 5 times greater variability in hair strength than that of women above that age. CONCLUSION: The results of our study indicate that hair tendency to grow persists up to 30 years of age, then slowly decreases and then achieves a steady state around 60 years of age.