Simultaneous Spin Coating and Ring-Opening Metathesis Polymerization for the Rapid Synthesis of Polymer Films.

We report a highly controlled technique for the synthesis of polymer films atop a substrate by combining spin coating with ring-opening metathesis polymerization (ROMP), herein termed spin coating ROMP (scROMP). The scROMP approach combines polymer synthesis and deposition into one process, fabricating films of up to 36 cm2 in under 3 min with orders-of-magnitude reduction in solvent usage. This method can convert numerous norbornene-type molecules into homopolymers and random copolymers as uniform films on both porous and nonporous substrates. Film thickness can be varied from a few hundred nanometers to a few tens of micrometers based on spin speed and monomer concentration. The resulting polymers possess high MW (>100 kDa) and low polydispersity (PDI) (<1.2) values that are similar to ROMP polymers made in solution. We also devise a model to investigate the balance between convective monomer spin-off and polymer growth from the surface, which allows the determination of critical kinetic parameters for scROMP. Finally, translation of scROMP to porous supports enables the synthesis of thin film composite membranes that demonstrate the ability to dehydrate ethanol by pervaporation.

Interfacing poly(p-anisidine) with photosystem I for the fabrication of photoactive composite films.

Photosystem I (PSI) is an intrinsically photoactive multi-subunit protein that is found in higher order photosynthetic organisms. PSI is a promising candidate for renewable biohybrid energy applications due to its abundance in nature and its high quantum yield. To utilize PSI's light-responsive properties and to overcome its innate electrically insulating nature, the protein can be paired with a biologically compatible conducting polymer that carries charge at appropriate energy levels, allowing excited PSI electrons to travel within a composite network upon light excitation. Here, a substituted aniline, 4-methoxy-aniline (para-anisidine), is chemically oxidized to synthesize poly(p-anisidine) (PPA) and is interfaced with PSI for the fabrication of PSI-PPA composite films by drop casting. The resulting PPA polymer is characterized in terms of its structure, composition, thermal decomposition, spectroscopic response, morphology, and conductivity. Combining PPA with PSI yields composite films that exhibit photocurrent densities on the order of several µA cm-2 when tested with appropriate mediators in a 3-electrode setup. The composite films also display increased photocurrent output when compared to single-component films of the protein or PPA alone to reveal a synergistic combination of the film components. Tuning film thickness and PSI loading within the PSI-PPA films yields optimal photocurrents for the described system, with ∼2 wt% PSI and intermediate film thicknesses generating the highest photocurrents. More broadly, dilute PSI concentrations show significant importance in achieving high photocurrents in PSI-polymer films.

Photoactive and conductive biohybrid films by polymerization of pyrrole through voids in photosystem I multilayer films.

The combination of conducting polymers with electro- and photoactive proteins into thin films holds promise for advanced energy conversion materials and devices. The emerging field of protein electronics requires conductive soft materials in a composite with electrically insulating proteins. The electropolymerization of pyrrole through voids in a drop-casted photosystem I (PSI) multilayer film enables the straightforward fabrication of photoactive and conductive biohybrid films. The rate of polypyrrole (PPy) growth is reduced by the presence of the PSI film but is insensitive to its thickness, suggesting that rapid diffusion of pyrrole through the voids within the PSI film enables initiation at vacant areas on the gold surface. The base thickness of the composite tends to increase with time, as PPy chains propagate through and beyond the PSI film, coalescing to exhibit a tubule-like morphology as observed by scanning electron microscopy. Increasing amounts of PPy greatly increase the capacitance of the composite films in a manner almost identical to that of pure PPy films grown from unmodified gold, consistent with a high polymer/aqueous interfacial area and a conductive composite film. While PPy is not photoactive here, all composite films, including those with large amounts of PPy, exhibit photocurrents when irradiated by white light in the presence of redox mediator species. Optimization of the Py electropolymerization time is necessary, as increasing amounts of PPy lead to decreased photocurrent density due to a combination of light absorbance by the polymer and reduced accessibility of redox species to active PSI sites.

Drop-casted Photosystem I/cytochrome c multilayer films for biohybrid solar energy conversion.

One of the main barriers to making efficient Photosystem I-based biohybrid solar cells is the need for an electrochemical pathway to facilitate electron transfer between the P700 reaction center of Photosystem I and an electrode. To this end, nature provides inspiration in the form of cytochrome c6, a natural electron donor to the P700 site. Its natural ability to access the P700 binding pocket and reduce the reaction center can be mimicked by employing cytochrome c, which has a similar protein structure and redox chemistry while also being compatible with a variety of electrode surfaces. Previous research has incorporated cytochrome c to improve the photocurrent generation of Photosystem I using time consuming and/or specialized electrode preparation. While those methods lead to high protein areal density, in this work we use the quick and facile vacuum-assisted drop-casting technique to construct a Photosystem I/cytochrome c photoactive composite film with micron-scale thickness. We demonstrate that this simple fabrication technique can result in high cytochrome c loading and improvement in cathodic photocurrent over a drop-casted Photosystem I film without cytochrome c. In addition, we analyze the behavior of the cytochrome c/Photosystem I system at varying applied potentials to show that the improvement in performance can be attributed to enhancement of the electron transfer rate to P700 sites and therefore the PSI turnover rate within the composite film.

Surface-Initiated, Catechol-Containing Polymer Films for Effective Chelation of Aluminum Ions.

We present a new route for obtaining surface-tethered polymer films containing pendant catechol functional groups via surface-initiated activators regenerated by electron-transfer atom-transfer radical polymerization (SI-ARGET ATRP) of glycidyl methacrylate (GMA) and post-polymerization modification of the resulting poly(glycidyl methacrylate) (pGMA) films with dopamine. This method enables a high degree of functionalization of pGMA films with catechol groups at a controlled level, depending on the duration of the post-polymerization modification reaction. The dopamine-pGMA films readily absorbs Al3+ and Zn2+ ions, as verified by quartz crystal microbalance with dissipation (QCM-D) under continuous flow conditions, and demonstrates a four-fold molar selectivity to Al3+ over Zn2+. The ions desorb from the films upon rinsing with pure deionized (DI) water, which regenerates the catechol sites in the dopamine-pGMA film. Subsequent exposure to metal ions after rinsing steps yields reproducible levels of loading.

Layer-by-Layer Assembly of Photosystem I and PEDOT:PSS Biohybrid Films for Photocurrent Generation.

The design of electrode interfaces to achieve efficient electron transfer to biomolecules is important in many bioelectrochemical processes. Within the field of biohybrid solar energy conversion, constructing multilayered Photosystem I (PSI) protein films that maintain good electronic connection to an underlying electrode has been a major challenge. Previous shortcomings include low loadings, long deposition times, and poor connection between PSI and conducting polymers within composite films. Here, we show that PSI protein complexes can be deposited into monolayers within a 30 min timespan by leveraging the electrostatic interactions between the protein complex and the poly(3,4-ethylenedioxythiophene)-polystyrenesulfonate (PEDOT:PSS) polymer. Further, we follow a layer-by-layer (LBL) deposition procedure to produce up to 9-layer pairs of PSI and PEDOT:PSS with highly reproducible layer thicknesses as well as distinct changes in surface composition. When tested in an electrochemical cell employing ubiquinone-0 as a mediator, the photocurrent performance of the LBL films increased linearly by 83 ± 6 nA/cm2 per PSI layer up to 6-layer pairs. The 6-layer pair samples yielded a photocurrent of 414 ± 13 nA/cm2, after which the achieved photocurrent diminished with additional layer pairs. The turnover number (TN) of the PSI-PEDOT:PSS LBL assemblies also greatly exceeds that of drop-casted PSI multilayer films, highlighting that the rate of electron collection is improved through the systematic deposition of the protein complexes and conducting polymer. The capability to deposit high loadings of PSI between PEDOT:PSS layers, while retaining connection to the underlying electrode, shows the value in using LBL assembly to produce PSI and PEDOT:PSS bioelectrodes for photoelectrochemical energy harvesting applications.

pH-Responsive Copolymer Films Prepared by Surface-Initiated Polymerization and Simple Modification.

We report the preparation of pH-responsive, ester/carboxylic acid random copolymer films via simple modification of poly(norbornene diacyl chloride) (pNBDAC), prepared via surface-initiated ring-opening metathesis polymerization, with mixtures of water and ethanol to form carboxylic acid and ethyl ester side groups. The pNBDAC film serves as a compositionally versatile platform to controllably obtain copolymers with multiple functionalities. In modifying the pNBDAC to form the copolymer film, ethanol exhibits a significantly higher reactivity with acyl chloride groups within the film than does water. The magnitude and range of the pH-responsive performance are highly dependent on the carboxylic acid content in the copolymer films, which demonstrates the effect of film hydrophilicity on the pH-responsive switching of ionic barrier properties. The resistance of the film against ion transfer can be decreased by a factor of 104 through pH change, demonstrating pH-induced switching from hydrophobic and insulating to swollen and ion-permeable films. The interactions of the copolymer films with water at different pH values were also explored. When the copolymer contains 34% carboxylic acids, a 4× greater film thickness is obtained in high pH solution than in low pH solution due to ionically driven water swelling. The reversibility of the pH-responsive performance of these copolymer films is high based on measurements using quartz crystal microbalance with dissipation (QCM-D).

Photosystem I Enhances the Efficiency of a Natural, Gel-Based Dye-Sensitized Solar Cell.

The photosystem I (PSI) protein complex is known to enhance bioelectrode performance for many liquid-based photoelectrochemical cells. A hydrogel as electrolyte media allows for simpler fabrication of more robust and practical solar cells in comparison to liquid-based devices. This paper reports a natural, gel-based dye-sensitized solar cell that integrates PSI to improve device efficiency. TiO2-coated FTO slides, dyed by blackberry anthocyanin, act as a photoanode, while a film of PSI deposited onto copper comprises the photocathode. Ascorbic acid (AscH) and 2,6-dichlorophenolindophenol (DCPIP) are the redox mediator couple inside an agarose hydrogel, enabling PSI to produce excess oxidized species near the cathode to improve device performance. A comparison of performance at low pH and neutral pH was performed to test the pH-dependent properties of the AscH/DCPIP couple. Devices at neutral pH performed better than those at lower pH. The PSI film enhanced photovoltage by 75 mV to a total photovoltage of 0.45 V per device and provided a mediator concentration-dependent photocurrent enhancement over non-PSI devices, reaching an instantaneous power conversion efficiency of 0.30% compared to 0.18% without PSI, a 1.67-fold increase. At steady state, power conversion efficiencies for devices with and without PSI were 0.042 and 0.028%, respectively.

Optical and electrochemical tuning of hydrothermally synthesized nitrogen-doped carbon dots.

Carbon dots (CDs) are a rapidly progressing class of nanomaterial which show promise towards applications in solar energy conversion due to their low toxicity, favorable electrochemical properties, and tunability. In recent years there have been a number of reported CD syntheses, both top-down and bottom-up methods, producing a diverse range of CDs with intrinsic properties dependent on the starting materials and utilized dopants. This work presents a citrate buffer-facilitated synthesis of nitrogen-doped carbon dots (NCD) and explores the impact of urea concentration on observed electrochemical and optical properties. Optical absorbance and quantum yield of NCDs were found to increase with the dopant concentrations present in the hydrothermal reaction mixture. Electrochemical analysis demonstrates that increased nitrogen content results in the shifting of carbon dot oxidation potentials without the need of post-synthesis surface modifications. Over the range of molar ratios of dopant-to-citrate tested, the oxidation potentials of NCDs shifted up to 150 mV towards more negative potentials. X-ray photoelectron spectroscopy confirms the addition of pyrrolic and pyridinic nitrogen at different levels in different batches of NCDs, which are likely the source of the observed changes.

Polyviologen as Electron Transport Material in Photosystem I-Based Biophotovoltaic Cells.

The photosynthetic protein complex, photosystem I (PSI), can be photoexcited with a quantum efficiency approaching unity and can be integrated into solar energy conversion devices as the photoactive electrode. The incorporation of PSI into conducting polymer frameworks allows for improved conductivity and orientational control in the photoactive layer. Polyviologens are a unique class of organic polycationic polymers that can rapidly accept electrons from a primary donor such as photoexcited PSI and subsequently can donate them to a secondary acceptor. Monomeric viologens, such as methyl viologen, have been widely used as diffusible mediators in wet PSI-based photoelectrochemical cells on the basis of their suitable redox potentials for accepting electrons. Polyviologens possess similar electronic properties to their monomers with the added advantage that they can shuttle electrons in the solid state. Depositing polyviologen directly onto a film of PSI protein results in significant photocurrent enhancement, which confirms its role as an electron-transport material. The polymer film not only improves the photocurrent by aiding the electron transfer but also helps preserve the protein film underneath. The composite polymer-PSI assembly enhances the charge-shuttling processes from individual protein molecules within the PSI multilayer, greatly reducing charge-transfer resistances. The resulting PSI-based solid-state platform demonstrates a much higher photocurrent than the corresponding photoelectrochemical cell built using a similar architecture.

Co-Poly(ionic liquid) Films via Anion Exchange for the Continuous Tunability of Ion Transport and Wettability.

This manuscript details a novel and simple approach to achieve surface-tethered co-poly(ionic liquid) (coPIL) films through the exchange of the resident anion of a poly(ionic liquid) (PIL) film with two or more anions. Initially, surface-tethered PIL films were prepared by the surface-initiated ring-opening metathesis polymerization of the ionic liquid monomer 3-[(bicyclo[2.2.1]hept-5-en-2-yl)methyl]-1,2-dimethylimidazol-3-ium hexafluorophosphate ([N1-dMIm][PF6]) whose PF6 - anion was easily interchanged with aqueous solutions containing a binary mixture of the PF6 - anion, along with perchlorate (ClO4 -) or bis(fluorosulfonyl)imide (FSI-) anions. The binary mole fraction of each anion in the film was determined from the infrared spectra of the coPIL films. The thermodynamically driven anion selectivity for exchange from the liquid phase into the coPIL films was determined to follow the order ClO4 - < PF6 - < FSI-. The aqueous wettability of p[N1-dMIm] coPIL films containing both the PF6 - and ClO4 - anions (p[N1-dMIm][PF6][ClO4]) was quantified by contact angle goniometry with the observation that the surface showed an enrichment in the ClO4 - anion compared to the average binary anion mole fraction of ClO4 - in the film (y ClO4 - ). The rate of ion transport through the p[N1-dMIm][PF6][ClO4] coPIL films, quantified by electrochemical impedance spectroscopy, linearly depends on the binary anion mole fraction of ClO4 - in solution (x ClO4 - ), enabling continuous tunability by over three orders of magnitude for ion conductivity in the coPIL films.

An Electrochemical Reaction-Diffusion Model of the Photocatalytic Effect of Photosystem I Multilayer Films.

The photosynthetic protein, photosystem I (PSI), has been used as a photoactive species within a host of biohybrid photoelectrochemical systems. PSI multilayer films at electrode surfaces provide greatly improved solar energy conversion relative to homologous monolayer films. While the photocatalytic effect of PSI multilayers has been theorized as an electrolyte-mediated mechanism, no comprehensive, first-principles modeling study has been presented. In this work, we develop and optimize an electrochemical reaction-diffusion model to replicate the significant electrochemical, physicochemical, and transport processes that underpin photocurrent development of a PSI multilayer film. We use this model to provide strong evidence that PSI's terminal cofactors rapidly exchange electrons with diffusible mediators and stimulate photocurrent principally due to alteration of mediator concentrations at a solution-electrode interface as governed by Butler-Volmer kinetics. Our fitted model accurately replicates photocurrent trends under a variety of conditions, including variable applied bias and PSI multilayer film thickness.

Surface-Initiated Ring-Opening Metathesis Polymerization of Dicyclopentadiene from the Vapor Phase.

Surface-attached polydicyclopentadiene (pDCPD) films were prepared on gold and silicon substrates via surface-initiated ring-opening metathesis polymerization (SI-ROMP) of dicyclopentadiene (DCPD). The films were grown utilizing monomer in both the vapor phase and the solution phase with the former process exhibiting rapid kinetics, producing ∼400-nm-thick pDCPD films in less than 1 min of polymerization. No significant differences in thickness were observed for films grown from monomer in the vapor phase with the different isomers (exo and endo) of DCPD. Decane was used as an inert additive to control the concentration of DCPD monomer in the vapor phase enabling the preparation of pDCPD films with thickness ranging from tens of nanometers to hundreds of nanometers. The thickness of pDCPD films polymerized using monomer in the vapor phase was enhanced by the presence of a rinse solvent on the surface of the ROMP-active gold substrates. The choice of ROMP catalyst was found to be an important consideration when SI-ROMP was conducted on different substrates. Electrochemical impedance spectroscopy was used to reveal that the films provide effective barriers to the diffusion of aqueous ions in excess of 1 × 106 Ω·cm2. The mechanical properties of the surface-tethered pDCPD films were quantified with AFM PeakForce quantitative nanomechanical mapping (QNM) with a measured reduced Young's modulus (Er) of 15 GPa. The measured Er was greater than that of a non-cross-linked surface-tethered polymer, pNB, indicating that the pDCPD films are stiffer.

Photocatalytic photosystem I/PEDOT composite films prepared by vapor-phase polymerization.

Photosystem I (PSI) achieves photo-induced charge separation with outstanding internal quantum efficiency and has been used to improve the performance of various photoelectrochemical systems. Herein, we describe a fast and versatile technique to assemble composite films containing PSI and a chosen intrinsically conductive polymer (ICP). A mixture of PSI and a Friedel-Crafts catalyst (FeCl3) is drop cast atop a substrate of choice. Contact with ICP monomer vapor at low temperature stimulates polymer growth throughout PSI films in minutes. We assess the effects of PSI loading on the rapid vapor-phase growth of poly(3,4-ethylenedioxythiophene) (PEDOT) within and above PSI multilayer films, and characterize the resulting film's thickness, electrochemical capacitance, and photocatalytic response. Composite films generate cathodic photocurrent when in contact with an aqueous redox electrolyte, confirming retention of the photocatalytic activity of the polymer-entrapped PSI multilayer assembly.

Watching the dynamics of electrons and atoms at work in solar energy conversion.

The photochemical reactions performed by transition metal complexes have been proposed as viable routes towards solar energy conversion and storage into other forms that can be conveniently used in our everyday applications. In order to develop efficient materials, it is necessary to identify, characterize and optimize the elementary steps of the entire process on the atomic scale. To this end, we have studied the photoinduced electronic and structural dynamics in two heterobimetallic ruthenium-cobalt dyads, which belong to the large family of donor-bridge-acceptor systems. Using a combination of ultrafast optical and X-ray absorption spectroscopies, we can clock the light-driven electron transfer processes with element and spin sensitivity. In addition, the changes in local structure around the two metal centers are monitored. These experiments show that the nature of the connecting bridge is decisive for controlling the forward and the backward electron transfer rates, a result supported by quantum chemistry calculations. More generally, this work illustrates how ultrafast optical and X-ray techniques can disentangle the influence of spin, electronic and nuclear factors on the intramolecular electron transfer process. Finally, some implications for further improving the design of bridged sensitizer-catalysts utilizing the presented methodology are outlined.

Construction of a Semiconductor-Biological Interface for Solar Energy Conversion: p-Doped Silicon/Photosystem I/Zinc Oxide.

The interface between photoactive biological materials with two distinct semiconducting electrodes is challenging both to develop and analyze. Building off of our previous work using films of photosystem I (PSI) on p-doped silicon, we have deposited a crystalline zinc oxide (ZnO) anode using confined-plume chemical deposition (CPCD). We demonstrate the ability of CPCD to deposit crystalline ZnO without damage to the PSI biomaterial. Using electrochemical techniques, we were able to probe this complex semiconductor-biological interface. Finally, as a proof of concept, a solid-state photovoltaic device consisting of p-doped silicon, PSI, ZnO, and ITO was constructed and evaluated.

Electrical Control of near-Field Energy Transfer between Quantum Dots and Two-Dimensional Semiconductors.

We investigate near-field energy transfer between chemically synthesized quantum dots (QDs) and two-dimensional semiconductors. We fabricate devices in which electrostatically gated semiconducting monolayer molybdenum disulfide (MoS2) is placed atop a homogeneous self-assembled layer of core-shell CdSSe QDs. We demonstrate efficient nonradiative Förster resonant energy transfer (FRET) from QDs into MoS2 and prove that modest gate-induced variation in the excitonic absorption of MoS2 leads to large (∼500%) changes in the FRET rate. This in turn allows for up to ∼75% electrical modulation of QD photoluminescence intensity. The hybrid QD/MoS2 devices operate within a small voltage range, allow for continuous modification of the QD photoluminescence intensity, and can be used for selective tuning of QDs emitting in the visible-IR range.

Electrochemical preparation of Photosystem I-polyaniline composite films for biohybrid solar energy conversion.

In this work, we report for the first time the entrapment of the biomolecular supercomplex Photosystem I (PSI) within a conductive polymer network of polyaniline via electrochemical copolymerization. Composite polymer-protein films were prepared on gold electrodes through potentiostatic electropolymerization from a single aqueous solution containing both aniline and PSI. This study demonstrates the controllable integration of large membrane proteins into rapidly prepared composite films, the entrapment of such proteins was observed through photoelectrochemical analysis. PSI's unique function as a highly efficient biomolecular photodiode generated a significant enhancement in photocurrent generation for the PSI-loaded polyaniline films, compared to pristine polyaniline films, and dropcast PSI films. A comprehensive study was then performed to separately evaluate film thickness and PSI concentration in the initial polymerization solution and their effects on the net photocurrent of this novel material. The best performing composite films were prepared with 0.1 µM PSI in the polymerization solution and deposited to a film thickness of 185 nm, resulting in an average photocurrent density of 5.7 µA cm(-2) with an efficiency of 0.005%. This photocurrent output represents an enhancement greater than 2-fold over bare polyaniline films and 200-fold over a traditional PSI multilayer film of comparable thickness.

Reproducing superhydrophobic leaves as coatings by micromolding surface-initiated polymerization.

Micromolding surface-initiated polymerization enables the fabrication of polymer coatings that reproduce the microscale surface topography of superhydrophobic leaves onto solid supports. Here, the surfaces of superhydrophobic leaves from Trifolium repens and Aristolochia esperanzae are molded and reproduced as the topography of a partially fluorinated polymer coating through the surface-initiated ring-opening metathesis polymerization of 5-(perfluorooctyl)norbornene (NBF8). The polymer coatings have thicknesses exceeding 100 µm, which can be tailored by the amount of monomer added to the mold. These coatings are robustly bound to the substrate, contain compositions not found in nature, and achieve superhydrophobicity that is comparable to the actual leaf.