Controlled Growth of Perovskite Nanocrystals on Nanotubes via a Nanoseeding Intermediate Stage: Toward Novel Optoelectronic Applications.

CsPbBr3 perovskite nanocrystals (CNCs) were densely anchored on multiwalled carbon nanotubes (MWNTs) via a nanoseeding intermediate stage, in which lead-based nuclei are formed on the nanotube surface. After the formation of the intermediate, a cesium precursor was added to promote the growth of CNCs from the surface nuclei and to thereby obtain CNC-decorated MWNT nanohybrids (CMNHs). The morphology and properties of the CMNHs were determined by the reaction temperature employed during their synthesis. Importantly, the use of MWNTs promoted the formation of larger CNCs that emitted intense green light and modified the electronic structure and bandgap energy of the CNCs. Consequently, the CMNHs could function as optoelectronic transducers and exhibit a "turn-on" photocurrent response when exposed to UV light of narrow specific-range wavelengths. In a novel approach for preventing counterfeit products, the CMNHs were used as a light-emitting black ink to create quick-response codes with fake pixels.

Design and Fabrication of Ultrathin Nanoporous Donor-Acceptor Copolymer-Based Organic Field-Effect Transistors for Enhanced VOC Sensing Performance.

The development of organic field-effect transistor (OFET) chemical sensors with high sensing performance and good air stability has remained a persistent challenge, thereby hindering their practical application. Herein, an OFET sensor based on a donor-acceptor copolymer is shown to provide high responsivity, sensitivity, and selectivity toward polar volatile organic compounds, as well as good air stability. In detail, a polymer blend of N-alkyl-diketopyrrolo-pyrrole-dithienylthieno[3,2-b]thiophene (DPP-DTT) and polystyrene is coated onto an FET substrate via shearing-assisted phase separation (SAPS) combined with selective solvent etching to fabricate the DPP-DTT-based OFET device having an ultrathin nanoporous structure suitable for gas sensing applications. This is achieved via optimization of the film morphology by varying the shear rate to adjust the dynamic balance between the shear and capillary forces to obtain an ultrathin thickness (∼8 nm) and nanopore size (80 nm) that are favorable for the efficient diffusion and interaction of analytes with the active layer. In particular, the sensor presents high responsivities toward methanol (∼70%), acetone (∼51.3%), ethanol (∼39%), and isopropyl alcohol (IPA) (∼29.8%), along with fast response and recovery times of ∼80 and 234 s, respectively. Moreover, the average sensitivity was determined to be 5.75%/ppm from the linear plot of the responsivity against the methanol concentration in the range of 1-100 ppm. Importantly, the device also exhibits excellent long-term (30-day) air and thermal storage stability, thereby demonstrating its high potential for practical applications.

High-Performance Nitric Oxide Gas Sensors Based on an Ultrathin Nanoporous Poly(3-hexylthiophene) Film.

Conjugated polymer (CP)-based organic field-effect transistors (OFETs) have been considered a potential sensor platform for detecting gas molecules because they can amplify sensing signals by controlling the gate voltage. However, these sensors exhibit significantly poorer oxidizing gas sensing performance than their inorganic counterparts. This paper presents a high-performance nitric oxide (NO) OFET sensor consisting of a poly(3-hexylthiophene) (P3HT) film with an ultrathin nanoporous structure. The ultrathin nonporous structure of the P3HT film was created via deposition through the shear-coating-assisted phase separation of polymer blends and selective solvent etching. The ultrathin nonporous structure of the P3HT film enhanced NO gas diffusion, adsorption, and desorption, resulting in the ultrathin nanoporous P3HT-film-based OFET gas sensor exhibiting significantly better sensing performance than pristine P3HT-film-based OFET sensors. Additionally, upon exposure to 10 ppm NO at room temperature, the nanoporous P3HT-film-based OFET gas sensor exhibited significantly better sensing performance (i.e., responsivity ≈ 42%, sensitivity ≈ 4.7% ppm-1, limit of detection ≈ 0.5 ppm, and response/recovery times ≈ 6.6/8.0 min) than the pristine P3HT-film-based OFET sensors.

Enhanced Nitric Oxide Sensing Performance of Conjugated Polymer Films through Incorporation of Graphitic Carbon Nitride.

Organic field-effect transistor (OFET) gas sensors based on conjugated polymer films have recently attracted considerable attention for use in environmental monitoring applications. However, the existing devices are limited by their poor sensing performance for gas analytes. This drawback is attributed to the low charge transport in and the limited charge-analyte interaction of the conjugated polymers. Herein, we demonstrate that the incorporation of graphitic carbon nitride (g-C3N4) into the conjugated polymer matrix can improve the sensing performance of OFET gas sensors. Moreover, the effect of graphitic carbon nitride (g-C3N4) on the gas sensing properties of OFET sensors based on poly(3-hexylthiophene) (P3HT), a conjugated polymer, was systematically investigated by changing the concentration of the g-C3N4 in the P3HT/g-C3N4 composite films. The obtained films were applied in OFET to detect NO gas at room temperature. In terms of the results, first, the P3HT/g-C3N4 composite films containing 10 wt.% g-C3N4 exhibited a maximum charge carrier mobility of ~1.1 × 10-1 cm2 V-1 S-1, which was approximately five times higher than that of pristine P3HT films. The fabricated P3HT/g-C3N4 composite film based OFET sensors presented significantly enhanced NO gas sensing characteristics compared to those of the bare P3HT sensor. In particular, the sensors based on the P3HT/g-C3N4 (90/10) composite films exhibited the best sensing performance relative to that of the bare P3HT sensor when exposed to 10 ppm NO gas: responsivity = 40.6 vs. 18.1%, response time = 129 vs. 142 s, and recovery time = 148 vs. 162 s. These results demonstrate the enormous promise of g-C3N4 as a gas sensing material that can be hybridized with conjugated polymers to efficiently detect gas analytes.

Morphology-Dependent Ambient-Condition Growth of Perovskite Nanocrystals for Enhanced Stability in Photoconversion Device.

CsPbBr3 perovskite nanocrystals with two different dimensionalities were synthesized at different temperatures and then integrated as optoelectronic transducers into transistor-type photoconversion devices. Postsynthesis transformation was observed for two-dimensional (2D) nanoplatelets, while the transformation was rarely found in 3D nanocubes. At ambient temperature and pressure, neighboring nanoplatelets made facet-to-facet contact and then fused into larger 2D nanoplatelets (2-5 times) without defects. The coalescence of 2D nanoplatelets at the ambient condition lowered the density of defects at the surface of the nanocrystals and thus could facilitate effective and stable photoconversion behavior in the nanocrystal film integrated into the device. Consequently, the ambient-condition aging of 2D nanoplatelets on device substrate led to 3 times higher retention in photoconversion performance. Importantly, these results provide a new concept of how perovskite nanocrystals can be integrated into a device for enhanced stability in device performance.