Nitrogen-Blowing Assisted Strategy for Fabricating Large-Area Organic Solar Modules with an Efficiency of 15.6.

Organic solar cells (OSCs) are one of the most promising photovoltaic technologies due to their affordability and adaptability. However, upscaling is a critical issue that hinders the commercialization of OSCs. A significant challenge is the lack of cost-effective and facile techniques to modulate the morphology of the active layers. The slow solvent evaporation leads to an unfavorable phase separation, thus resulting in a low power conversion efficiency (PCE) of organic solar modules. Here, a nitrogen-blowing assisted method is developed to fabricate a large-area organic solar module (active area = 12 cm2) utilizing high-boiling-point solvents, achieving a PCE of 15.6%. The device fabricated with a high-boiling-point solvent produces a more uniform and smoother large-area film, and the assistance of nitrogen-blowing accelerates solvent evaporation, resulting in an optimized morphology with proper phase separation and finer aggregates. Moreover, the device fabricated by the nitrogen-blowing assisted method exhibits improved exciton dissociation, balanced carrier mobility, and reduced charge recombination. This work proposes a universal and cost-effective technique for the fabrication of high-efficiency organic solar modules.

In-Doped ZnO Electron Transport Layer for High-Efficiency Ultrathin Flexible Organic Solar Cells.

Sol-gel processed zinc oxide (ZnO) is one of the most widely used electron transport layers (ETLs) in inverted organic solar cells (OSCs). The high annealing temperature (≈200 °C) required for sintering to ensure a high electron mobility however results in severe damage to flexible substrates. Thus, flexible organic solar cells based on sol-gel processed ZnO exhibit significantly lower efficiency than rigid devices. In this paper, an indium-doping approach is developed to improve the optoelectronic properties of ZnO layers and reduce the required annealing temperature. Inverted OSCs based on In-doped ZnO (IZO) exhibit a higher efficiency than those based on ZnO for a range of different active layer systems. For the PM6:L8-BO system, the efficiency increases from 17.0% for the pristine ZnO-based device to 17.8% for the IZO-based device. The IZO-based device with an active layer of PM6:L8-BO:BTP-eC9 exhibits an even higher efficiency of up to 18.1%. In addition, a 1.2-micrometer-thick inverted ultrathin flexible organic solar cell is fabricated based on the IZO ETL that achieves an efficiency of 17.0% with a power-per-weight ratio of 40.4 W g-1, which is one of the highest efficiency for ultrathin (less than 10 micrometers) flexible organic solar cells.

Buried interface molecular hybrid for inverted perovskite solar cells.

Perovskite solar cells (PSCs) with an "inverted" architecture are a key pathway for commercializing this emerging photovoltaic technology due to the better power conversion efficiency (PCE) and operational stability as compared to the "normal" device structure. Specifically, PCEs of the inverted PSCs have exceeded 25% owing to the development of improved self-assembled molecules (SAMs)1-5 and passivation strategies6-8. Nevertheless, poor wettability and agglomerations of SAMs9-12 will cause interfacial losses, impeding further improvement in PCE and stability. Herein, we report on molecular hybrid at the buried interface in inverted PSCs by co-assembling a multiple carboxylic acid functionalized aromatic compound of 4,4',4''-nitrilotribenzoicacid (NA) with a popular SAM of [4-(3,6-dime-thyl-9H-carbazol-9-yl)butyl]phosphonic acid (Me-4PACz) to improve the heterojunction interface. The molecular hybrid of Me-4PACz with NA could substantially improve the interfacial characteristics. The resulting inverted PSCs demonstrated a record-certified steady-state efficiency of 26.54%. Crucially, this strategy aligns seamlessly with large-scale manufacturing, achieving the highest certified PCE for inverted mini-modules at 22.74% (aperture area: 11.1 cm2). Our device also maintained 96.1% of its initial PCE after more than 2,400 hours of 1-sun operation in ambient air.

Ecotoxicity and resistance genes induction changing of antibiotic tetracycline degradation products dominated by differential free radicals.

Studying the ecological risks of antibiotics and their degradation products is of great importance to water environment security and advanced oxidation processes (AOPs) development. This work studied the changes and internal influencing mechanisms of ecotoxicity and the capacity for inducing antibiotic resistance genes (ARGs) shown by the tetracycline (TC) degradation products generated in AOPs with differential free radicals. Under the action of superoxide radicals and singlet oxygen in the ozone system, and sulfate and hydroxyl radicals in the thermally activated potassium persulfate system, TC exhibited differential degradation pathways and resulted in the differential growth inhibition trends on the determined strains. Microcosm experiments combined with metagenomics were also performed to analyze the remarkable changes in the TC resistance genes tetA (60), tetT, and otr(B) induced by the degradation products and ARG hosts in the natural water environment. Microcosm experiments exhibited that the microbial community in actual water have changed significantly with the addition of TC and degradation intermediates. Furthermore, the richness of genes related to oxidative stress was investigated to discuss the effect on reactive oxygen species production and SOS response caused by TC and its intermediates.

Release of Zinc and Polycyclic Aromatic Hydrocarbons From Tire Crumb Rubber and Toxicity of Leachate to Daphnia magna: Effects of Tire Source and Photoaging.

Tire crumb rubber (TCR) has been widely used in artificial turf fields, however, the potential environmental risk of TCR and the effect of sunlight exposure are scarcely studied. Here, we evaluated leachability of Zn and polycyclic aromatic hydrocarbons (PAHs) in four types of TCRs and acute toxicity of leachates to Daphnia magna. The results showed that all types of TCRs tested released Zn (0.20-1.3 µg/g) and PAHs (9.4-17 µg/g) but only two were lethal to D. magna (mortality 73%). Notably, ultraviolet (UV) irradiation induced TCR to generate acidic leachate (pH ~ 4.8), which contained 24- and 1.2-fold higher concentrations of Zn and PAHs and therefore was more toxic to D. magna than that in the absence of UV treatment. These findings demonstrate source-dependent toxicity of TCR and highlight the need to consider the effect of photoaging when evaluating the environmental risks of TCR.