RESUMO
Laser-induced breakdown spectroscopy (LIBS) has become a very attractive and popular chemical analysis technique in material science for its advantage of rapid analysis, non-contact measurement, micro surface analysis and online analysis. In this paper, LIBS were used to determine insoluble aluminum content by analyzing the scanning data on massive steel samples. Abnormal data were discarded by Nalimov criterion, and the remaining data was used to calculate the average and the standard deviation. The threshold to distinguish acid-insoluble aluminum and soluble aluminum was identified as the average value plus triple standard deviation. Two different mathematical models were proposed to calculate insoluble aluminum content, respectively according to the ratio of the total acid-insoluble aluminium signal strength to total aluminum signal strength and acid-insoluble signal number to total aluminum signal number. The total aluminum content was determined by the calibration curve. Insoluble aluminum content of certified reference materials and plate blank samples obtained by mathematical model is coincident to chemical wet method results. The result according to total acid-insoluble aluminium signal strength is much better. LIBS can be used as a rapid analysis method to characterize insoluble aluminum content in steel samples.
RESUMO
In the present paper, apparatus and theory of surface analysis is introduced, and the progress in the application of laser ablation ICP-MS to microanalysis in ferrous, nonferrous and semiconductor field is reviewed in detail. Compared with traditional surface analytical tools, such as SEM/EDS (scanning electron microscopy/energy dispersive spectrum), EPMA (electron probe microanalysis analysis), AES (auger energy spectrum), etc. the advantage is little or no sample preparation, adjustable spatial resolution according to analytical demand, multi-element analysis and high sensitivity. It is now a powerful complementary method to traditional surface analytical tool. With the development of LA-ICP-MS technology maturing, more and more analytical workers will use this powerful tool in the future, and LA-ICP-MS will be a super star in elemental analysis field just like LIBS (Laser-induced breakdown spectroscopy).
RESUMO
Over the past decade there has been intense activity in the study and development of laser-induced breakdown spectroscopy (LIBS). As a new tool for surface microanalysis, it caused widespread in materials science because of the advantage of rapid and high sensitivity. In the present paper, the distribution of Ni, Mn, C and Si near weld fusion line was analyzed on two kinds of weld sample. Line scanning mode analysis was carried out by three different kinds of methods, namely laser-induced breakdown spectroscopy (LIBS), scanning electron microscope/energy dispersive spectrometer (SEM/EDS) and electron probe X-ray microanalyser (EPMA). The concentration variation trend of Ni and Mn acquired by LIBS is coincident with SEM/EDS and EPMA. The result shows that the content of Ni and Mn was significantly different between weld seam and base metal on both the samples. The content of Ni and Mn was much higher in weld seam than in base metal, and a sharp concentration gradient was analyzed in the fusion zone. According to the distribution of Ni and Mn, all the three methods got a similar value of welded fusion zone width. The concentration variation trend of C and Si acquired by LIBS is not coincident with SEM/EDS and EPMA. The concentration difference between weld seam and base metal was analyzed by LIBS, but had not by SEM/EDS and EPMA, because of the low concentration and slight difference. The concentration gradient of C and Si in fusion zone was shows clearly by LIBS. For higher sensitivity performance, LIBS is much more adapted to analyze low content element than SEM/EDS and EPMA.
RESUMO
In the present paper, under optimum experimental condition, two middle-low alloy slab and homogeneous samples were analyzed under the condition of spatial resolution about 100 microm by scanning mode. Element 2D intensity distribution can be converted into 2D concentration distribution via establishing calibration curve. The results showed that there is a central segregation for C, Si, Mn, P, S and Cu for 86 # slab sample, and C, Si, P and Ti for 174 # slab sample, the width of segregation band was estimated, and it agrees well with metallographic analysis. Homogeneous sample was analyzed by scanning mode, the result showed that C, Si, Mn, P, S and so on are well distributed, and there is no segregation band existing. 2D distribution of element intensity or concentration can be used to indirectly reflect sample's homogeneity. Compared with traditional metallographic analysis, LIBS can not only show central segregation bands position and width, but also provide 2D concentration distribution for C, Si, Mn, P, S etc in detail. This method can be used to characterize segregation band position and its width rapidly, and provide theoretical guidance for improving metallurgical process.
RESUMO
As a truly surface analytical tool, laser-induced breakdown spectroscopy (LIBS) was developed in recent ten years, and in this paper, fundamental theory, instrumentation and it's applications in material science are reviewed in detail. Application progress of elemental distribution and depth profile analysis are mainly discussed in the field of metallurgy, semiconductor and electronical materials at home and abroad. It is pointed out that the pulse energy, ambient gas and it's pressure, and energy distribution of laser beam strongly influence spatial and depth resolution, and meanwhile a approach to improving resolution considering analytical sensitivity is provided. Compared with traditional surface analytical methods, the advantage of LIBS is very large scanning area, high analytical speed, and that conducting materials or non-conducting materials both can be analyzed. It becomes a powerful complement of traditional surface analytical tool.
