Oral Biofilm Cryotherapy as a Novel Ecological Modulation Approach.

Oral cryotherapy is used in dentistry as a safe, simple, and low-cost treatment for a variety of oral lesions. It is well known for its ability to aid in the healing process. However, its effect on oral biofilms is unknown. As a result, the purpose of this study was to assess the effects of cryotherapy on in vitro oral biofilms. In vitro multispecies oral biofilms were grown on the surface of hydroxyapatite discs in symbiotic or dysbiotic states. CryoPen X+ was used to treat the biofilms, whereas untreated biofilms served as control. One set of biofilms was collected for study immediately after cryotherapy, whereas another group was reincubated for 24 h to permit biofilm recovery. Changes in biofilm structure were analyzed with a confocal laser scanning microscope (CLSM) and a scanning electron microscope (SEM), while biofilm ecology and community compositional changes were analyzed with viability DNA extraction and quantitative polymerase chain reaction (v-qPCR) analysis. One cryo-cycle immediately reduced biofilm load by 0.2 to 0.4 log10 Geq/mL, which increased with additional treatment cycles. Although the bacterial load of the treated biofilms recovered to the same level as the control biofilms within 24 h, the CLSM detected structural alterations. Compositional alterations were also detected by SEM, corroborating the v-qPCR findings that showed ≈≤10% incidence of pathogenic species compared to nontreated biofilms that encompassed ≈45% and 13% pathogenic species in dysbiotic and symbiotic biofilms, respectively. Spray cryotherapy showed promising results in a novel conceptual approach to the control of oral biofilms. Acting selectively by targeting oral pathobionts and retaining commensals, spray cryotherapy could modify the ecology of in vitro oral biofilms to become more symbiotic and prevent the evolution of dysbiosis without the use of antiseptics/antimicrobials.

Variation of the crystal growth of mesoporous silica nanoparticles and the evaluation to ibuprofen loading and release.

Mesoporous silica nanoparticles (MSNs) were synthesized with variable microwave power in the range of 100-450 W, and the resulting enhancement of MSN crystal growth was evaluated for the adsorption and release of ibuprofen. X-ray diffraction (XRD) revealed that the MSN prepared under the highest microwave power (MSN450) produced the most crystallized and prominent mesoporous structure. Enhancement of the crystal growth improved the hexagonal order and range of silica, which led to greater surface area, pore width and pore volume. MSN450 exhibited higher ibuprofen adsorption (98.3 mg/g), followed by MSN300(81.3 mg/g) and MSN100(74.1 mg/g), confirming that more crystallized MSN demonstrated higher adsorptivity toward ibuprofen. Significantly, MSN450 also contained more hydroxyl groups that provided more adsorption sites. In addition, MSN450 exhibited comparable ibuprofen adsorption with conventionally synthesized MSN, indicating the potential of microwave treatment in the synthesis of related porous materials. In vitro drug release was also investigated with simulated biological fluids and the kinetics was studied under different pH conditions. MSN450 showed the slowest release rate of ibuprofen, followed by MSN300 and MSN100. This was due to the wide pore diameter and longer range of silica order of the MSN450. Ibuprofen release from MSN450 at pH 5 and 7 was found to obey a zero-order kinetic model, while release at pH 2 followed the Kosmeyer-Peppas model.

Influence of multi-walled carbon nanotubes on textural and adsorption characteristics of in situ synthesized mesostructured silica.

Carbon nanotubes-mesostructured silica nanoparticles (CNT-MSN) composites were prepared by a simple one step method with various loading of CNT. Their surface properties were characterized by XRD, N2 physisorption, TEM and FTIR, while the adsorption performance of the CNT-MSN composites were evaluated on the adsorption of methylene blue (MB) while varying the pH, adsorbent dosage, initial MB concentration, and temperature. The CNTs were found to improve the physicochemical properties of the MSN and led to an enhanced adsorptivity for MB. N2 physisorption measurements revealed the development of a bimodal pore structure that increased the pore size, pore volume and surface area. Accordingly, 0.05 g L(-1) CNT-MSN was able to adsorb 524 mg g(-1) (qm) of 60 mg L(-1) MB at pH 8 and 303 K. The equilibrium data were evaluated using the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models, with the Langmuir model affording the best fit to the adsorption data. The adsorption kinetics were best described by the pseudo-first order model. These results indicate the potential of CNT-MSN composites as effective new adsorbents for dye adsorption.

Amino modified mesostructured silica nanoparticles for efficient adsorption of methylene blue.

In this work, mesostructured silica nanoparticles (MSN(AP)) with high adsorptivity were prepared by a modification with 3-aminopropyl triethoxysilane (APTES) as a pore expander. The performance of the MSN(AP) was tested by the adsorption of MB in a batch system under varying pH (2-11), adsorbent dosage (0.1-0.5 g L(-1)), and initial MB concentration (5-60 mg L(-1)). The best conditions were achieved at pH 7 when using 0.1 g L(-1) MSN(AP) and 60 mg L(-1)MB to give a maximum monolayer adsorption capacity of 500.1 mg g(-1) at 303 K. The equilibrium data were evaluated using the Langmuir, Freundlich, Temkin, and Harkins-Jura isotherms and fit well to the Freundlich isotherm model. The adsorption kinetics was best described by the pseudo-second order model. The results indicate the potential for a new use of mesostructured materials as an effective adsorbent for MB.

Utilization of bivalve shell-treated Zea mays L. (maize) husk leaf as a low-cost biosorbent for enhanced adsorption of malachite green.

In this work, two low-cost wastes, bivalve shell (BS) and Zea mays L. husk leaf (ZHL), were investigated to adsorb malachite green (MG) from aqueous solutions. The ZHL was treated with calcined BS to give the BS-ZHL, and its ability to adsorb MG was compared with untreated ZHL, calcined BS and Ca(OH)(2)-treated ZHL under several different conditions: pH (2-8), adsorbent dosage (0.25-2.5 g L(-1)), contact time (10-30 min), initial MG concentration (10-200 mg L(-1)) and temperature (303-323 K). The equilibrium studies indicated that the experimental data were in agreement with the Langmuir isotherm model. The use of 2.5 g L(-1) BS-ZHL resulted in the nearly complete removal of 200 mg L(-1) of MG with a maximum adsorption capacity of 81.5 mg g(-1) after 30 min of contact time at pH 6 and 323 K. The results indicated that the BS-ZHL can be used to effectively remove MG from aqueous media.