Critical evaluations on the crystallographic properties of translucent dental zirconia ceramics stabilized with 3-6 mol% yttria.

OBJECTIVES: This study aimed to determine the crystalline phase composition of 3-6 mol% yttria-stabilized zirconia (3-6YSZ), specifically investigating the presence of tetragonal (t), cubic (c), and/or additional yttria-rich tetragonal (t') phase. METHODS: Laboratory-fabricated specimens comprising 3-5YSZ, resembling translucent dental zirconia ceramics (TZ specimens), and a blend of 3YSZ and 8YSZ, representing a c-phase reference, were prepared. Additionally, 25 dental zirconia products stabilized with 3-6 mol% yttria were analyzed. Whole X-ray diffraction (XRD) patterns were obtained for Rietveld analysis, complemented by fine scanning in the 2θ region from 72º to 76º for qualitative phase analysis. Moreover, yttria concentrations in each specimen were determined using X-ray fluorescence (XRF) spectroscopy. RESULTS: In the 2θ region from 72º to 76º, TZ and dental zirconia product specimens displayed four peaks attributed to t- and t'-phases, but the c-phase peak was absent. Rietveld analysis of the whole XRD patterns, utilizing a t-t' model, demonstrated the t-phase fraction ranging from 86 mass% in 3YSZ to 11 mass% in 6YSZ. Rietveld analysis appeared reliable, as the yttria contents calculated based on lattice parameters aligned well with those measured by XRF. This study established that dental 3-6YSZ consisted of yttria-lean t- and yttria-rich t'-phases. SIGNIFICANCE: The present study enhances understanding of the crystalline structure of dental zirconia ceramics. Future crystallographic analyses of these ceramics should consider the presence of t- and t'-phases.

Impact of Vascular Access Flow Suppression Surgery on Cervical Artery Circulation: A Retrospective Observational Study.

Vascular access (VA) flow suppression surgery augments VA flow resistance and can increase other circulation flows hindered by high-flow VA. However, whether VA flow suppression surgery affects cervical circulation has rarely been reported. We aimed to determine the effect of VA flow suppression surgery on the cervical circulation in patients with high-flow VA. This single-center, retrospective, observational study included 85 hemodialysis patients who underwent VA flow suppression surgery at the Kanno Dialysis and Access Clinic between 2009 and 2018. Blood flow in the VA, bilateral vertebral arteries, and common carotid artery was measured before and after VA flow suppression surgery. The VA flow decreased from 1548 mL/min to 693 mL/min postoperatively. The flow of the vertebral artery on the VA side increased from 55 mL/min to 81 mL/min. The flow in the bilateral common carotid arteries also increased. Patients whose symptoms improved postoperatively showed better improvement in the vertebral artery on the VA side. VA flow suppression surgery in patients with high-flow VA increases the flow of the vertebral artery on the VA side and of the bilateral common carotid arteries. High-flow VA can hinder the vertebral and common carotid circulation.

Mutagenicity assessment of high-power 1.6-THz pulse laser radiation.

The effect of terahertz (THz) radiation has been studied in medicine. However, there is a lack of scientific information regarding its possible mutagenicity. Therefore, the present study aimed to assess the mutagenicity of 1.6 THz laser irradiation. The Ames test was conducted using five bacterial tester strains. The bacteria were subjected to (i) 1.6 THz laser irradiation at 3.8 mW/cm2 for 60 min using a tabletop THz pulse laser system, (ii) ultraviolet irradiation, (iii) treatment with positive control chemicals (positive control) or (iv) treatment with the solvent used in the positive control (negative control). After treatment, the bacterial suspensions were cultured on minimal glucose agar to determine the number of revertant colonies. In addition, the comet assay was performed using fibroblasts (V79) to assess possible DNA damage caused by the THz laser irradiation. The Ames test demonstrated that the THz laser irradiation did not increase the number of revertant colonies compared to that in the negative control group, whereas the ultraviolet irradiation and positive control treatment increased the number of revertant colonies. Thus, 1.6 THz laser irradiation is unlikely to be mutagenic. The comet assay additionally suggests that the THz laser irradiation unlikely induce cellular DNA damage.

Residual stress associated with crystalline phase transformation of 3-6 mol% yttria-stabilized zirconia ceramics induced by mechanical surface treatments.

Monolithic dental prostheses made of 3-6 mol% yttria-stabilized zirconia (3-6YSZ) have gained popularity owing to their improved material properties and semi-automated fabrication processes. In this study, we aimed to evaluate the influence of mechanical surface treatments, such as polishing, grinding, and sandblasting, on the residual stress of 3-6YSZ used for monolithic prostheses in association with crystalline phase transformation. Plate specimens were prepared from five dental zirconia blocks: Aadva Zirconia ST (3YSZ), Aadva Zirconia NT (6YSZ), Katana HT (4YSZ), Katana STML (5YSZ), and Katana UTML (6YSZ). The specimens were either polished using 1, 3, or 9 µm diamond suspensions, ground using 15, 35, or 55 µm diamond discs, or sandblasted at 0.2, 0.3, or 0.4 MPa. The residual stress, crystalline phase, and hardness were analyzed using the cosα method, X-ray diffraction (XRD), and Vickers hardness test, respectively. Additionally, we analyzed the residual stress on the surfaces of monolithic zirconia crowns (MZCs) made of 4YSZ, 5YSZ, and 6YSZ, which were processed using clinically relevant procedures, including manual grinding, followed by polishing using a dental electric motor on the external surface, and sandblasting on the internal surface. Residual stress analysis demonstrated that grinding and sandblasting, particularly the latter, resulted in the generation of compressive residual stress on the surfaces of the plate specimens. XRD revealed that the ground and sandblasted specimens contained a larger amount of the rhombohedral phase than that of the polished specimens, which may be a cause of the residual stress. Sandblasting significantly increased the Vickers hardness compared to polishing, which may possibly be due to the generation of compressive residual stress. In the case of MZCs, compressive residual stress was detected not only on the sandblasted surface, but also on the polished surface. The difference in the residual stress between the plate and crown specimens may be related to the force applied during the automated and manual grinding and polishing procedures. Further studies are required to elucidate the effects of the compressive residual stress on the clinical performance of MZCs.

Inhibition of tooth demineralization caused by Streptococcus mutans biofilm via antimicrobial treatment using hydrogen peroxide photolysis.

OBJECTIVES: An antimicrobial technique utilizing hydroxyl radicals generated by the photolysis of 3% H2O2 has been developed recently. The present study aimed to evaluate the effect of H2O2 photolysis treatment on tooth demineralization caused by Streptococcus mutans biofilm. MATERIALS AND METHODS: To induce tooth demineralization, S. mutans biofilm was allowed to form on the maxillary first molars collected from Wistar rats via 24-h culturing. The samples were immersed in 3% H2O2 and irradiated with 365-nm LED (H2O2 photolysis treatment). Viable bacterial counts in the biofilm were evaluated immediately after treatment and after an additional 30-h culturing by colony counting. The acidogenicity of the biofilm, re-established 30 h after treatment, was assessed by measuring the pH. The effect of H2O2 photolysis treatment on tooth demineralization was assessed by measuring the depth of the radiolucent layer in micro-CT images. RESULTS: H2O2 photolysis significantly reduced viable bacterial counts in the biofilm to 3.7 log colony forming units (CFU)/sample, while the untreated group had 7.9 log CFU/sample. The pH of the biofilm re-established after treatment (6.6) was higher than that of the untreated group (5.3). In line with the pH measurement, the treatment group had a significantly lower depth of radiolucent layer in dentin than the untreated group. CONCLUSIONS: H2O2 photolysis treatment was effective not only in killing the biofilm-forming S. mutans but also in lowering the acidogenicity of the biofilm. Thus, this technique could inhibit tooth demineralization. CLINICAL RELEVANCE: H2O2 photolysis can be applicable as a new dental caries treatment.

Impact of adhesive primer and light-curing on polymerization kinetics of self-adhesive resin cement in association with free radical reaction.

This study analyzed the impact of adhesive primer and light-curing on the polymerization kinetics of urethane dimethacrylate-based self-adhesive resin cement combined with free radical reaction. Specimens were prepared by mixing the cement paste with or without adhesive primer. Subsequently, specimens were light-cured or set without light-curing. The degree of conversion (DC), Vickers hardness (Hv), and free radical concentrations were repeatedly measured up to 168 h after the curing initiation. Irrespective of the curing procedures, DC, Hv, and free radical concentration rapidly increased during the initial 30 min of curing. The specimens cured with adhesive primer and/or light-curing generally showed higher values of DC, Hv, and radical concentration than those set by chemical curing alone, especially during the initial polymerization phase. Kinetic analysis using a linear mixed model revealed that the adhesive primer had a higher coefficient estimate than light-curing, indicating that the former had a higher impact on the polymerization. Additionally, the adhesive primer alleviated the Hv reduction caused by water and air during the initial polymerization phase, although light-curing hardly prevented the polymerization inhibition. Therefore, we suggest that application of adhesive primer is beneficial to achieve higher degree of conversion and better mechanical properties of self-adhesive resin cements by enhancing free radical reactions.

Impact of a change in vascular access flow volume after percutaneous transluminal angioplasty on cardiac function.

Vascular access (VA) is necessary for patients on hemodialysis, and percutaneous transluminal angioplasty (PTA) is a useful treatment for maintaining VA function. PTA immediately increases the VA flow volume, which can affect cardiac function. We investigated the relationship between changes in VA flow volume and cardiac function in patients who underwent PTA. This was a single-center retrospective observational study, including patients who underwent PTA between June 2016 and August 2016. VA flow volume and cardiac function were measured by sonography before and 1 h after PTA. This study included 50 PTA procedures in 50 cases. PTA significantly increased the median VA flow volume from 445 (range, 150-1229) to 725 (350-1268) mL/min. Although the ejection fraction and diameter of the inferior vena cava were unchanged, the cardiac output (CO) and cardiac index increased significantly in most cases. Surprisingly, the CO was decreased in 18% of cases despite the increased VA flow volume. In this atypical group, a high CO before PTA was found to be a significant factor for the decrease in CO by PTA. In most cases, both VA flow volume and CO were increased by PTA, whereas in some cases, the CO was decreased despite an increase in VA flow volume. This atypical phenomenon may be due to the insufficient adaptive response in the peripheral artery and heart and could predict risks for future cardiac events. Therefore, it is important that such patients are carefully followed up on.

Reactions of dental pulp to hydrogen peroxide photolysis-based antimicrobial chemotherapy under ultraviolet-A irradiation in rats.

Hydrogen peroxide photolysis-based antimicrobial chemotherapy that utilizes ultraviolet-A irradiation (UVA-H2O2 photolysis) has been previously proposed as a method of treatment of cariogenic biofilm. Therefore, in the present study, we aimed to assess time-dependent reactions in the dental pulp of rats after UVA-H2O2 photolysis. Maxillary first molars were treated. UVA irradiation (wavelength: 365 nm) with 3 wt% H2O2 was performed for 90 s at a radiant emittance of 500-2000 mW/cm2 on the rats for 3 consecutive days or only 1 day. The animals were sacrificed at Days 1, 3, 7, and 21 after the treatment for the histological evaluation of inflammatory cells and immunohistochemistry of heat shock protein (HSP)-25, a marker of odontoblasts. Tertiary dentin formation was evaluated at Day 21 by histomorphometry and micro-CT analysis. UVA-H2O2 photolysis elicited little infiltration of inflammatory cells, but disturbances in the odontoblast layer and/or presence of localized degenerative tissue were observed on Day 3. This condition was followed by a healing process that was characterized by the reappearance of HSP-25 positive odontoblast-like cells at Day 7 and tertiary dentin formation at Day 21. The amount of tertiary dentin formed was dependent on the intensity of treatment; repeated UVA irradiations of H2O2 at 2000 mW/cm2 resulted in the largest amount of tertiary dentin formation at the pulp horn regions. Our findings suggest that UVA-H2O2 photolysis treatment can be used to treat dental caries clinically because the post-treatment inflammatory reaction was minimal and tertiary dentin formation was substantial, which may prove effective in protecting dental pulp from external irritants. As a cautionary consideration, the radiant emittance of the UVA irradiation should be carefully optimized before clinical application.

Mechanical and microstructural properties of ultra-translucent dental zirconia ceramic stabilized with 5 mol% yttria.

Monolithic dental prostheses fabricated from 3 mol.% yttria-stabilized zirconia (3YZ) are becoming increasingly popular. Recently, 5 mol.% yttria-stabilized zirconia (5YZ) which significantly improves the translucency of 3YZ has been prepared. However, its mechanical and microstructural properties, especially those affected by low-temperature degradation (LTD), have not been fully elucidated yet. The objective of the present study was to establish the relationship between the flexural strength of 5YZ with or without autoclave-induced LTD and its microstructural properties. For this purpose, a total of 320 bar-shaped specimens were cut from 5YZ and 3YZ blocks, and half of the specimens in each group were autoclaved at 134 °C for 50 h. Their flexural strengths were determined by conducting three-point bending tests, and the obtained results were analyzed by the Weibull statistical method. Grain sizes and crystalline structures of the specimens were analyzed by scanning electron microscopy (SEM) and X-ray diffraction, respectively. Additionally, the LTD-induced phase transformation was examined by Raman microscopy and cross-sectional surface analysis. The characteristic strengths of 5YZ and 3YZ were approximately 620 and 950 MPa, respectively, and 5YZ was found to be more resistant to LTD in terms of phase transformation than 3YZ. However, a low amount of the monoclinic phase was detected even in 5YZ after 50 h of autoclaving, which significantly decreased its flexural strength and reliability. The results of SEM analysis revealed that 5YZ was composed of two distinct regions: a dominant matrix with large grains (median size: 0.8 µm) and scattered areas with small grains (median size: 0.4 µm). Phase transformation analysis and fractography data indicated that the small-grain region was strongly affected by LTD and likely represented a fracture origin. The described properties should be considered during the clinical application of monolithic 5YZ dental prostheses.

Proanthocyanidin-rich grape seed extract improves bone loss, bone healing, and implant osseointegration in ovariectomized animals.

The purpose of the present study was to confirm if proanthocyanidin-rich grape seed extract (GSE) had the ability to improve bone health such as bone loss, bone healing, and implant osseointegration (defined as the direct connection between bone tissue and an implant) in ovariectomized (OVX) animals. We demonstrated that daily oral administration of GSE prevented bone loss in the lumbar vertebrae and femur in OVX mice. In addition, osteoclastogenesis in the lumbar spine bone of OVX mice, as assessed by histological and histomorphometric analyses, was accelerated but GSE prevented this dynamization, suggesting that GSE could counteract OVX-induced accelerated osteoclastogenic activity. In rats, OVX clearly impaired the healing of defects created on the calvaria, and GSE overcame this OVX-impaired healing. In the same way, osseointegration of a tibial implant in rats was retarded by OVX, and GSE counteracted the OVX-induced poor osseointegration, likely promoting bone healing by preventing imbalanced bone turnover. These results suggest that orally administered GSE improved implant osseointegration by mitigating the impaired bone health induced by OVX as a model of estrogen deficiency.

Bactericidal activity and recovery effect of hydroxyl radicals generated by ultraviolet irradiation and silver ion application on an infected titanium surface.

This study investigated the bactericidal effect, the underlying mechanisms of treatment, and recovery of biocompatibility of the infected titanium surface using a combination treatment of silver ion application and ultraviolet-A (UV-A) light irradiation. Streptococcus mutans and Aggregatibacter actinomycetemcomitans were used in suspension and as a biofilm on a titanium surface to test for the bactericidal effect. The bactericidal effect of the combination treatment was significantly higher than that of silver ion application or UV-A light irradiation alone. The bactericidal effect of the combination treatment was attributable to hydroxyl radicals, which generated from the bacterial cell wall and whose yield increased with the silver concentration. To assess the biocompatibility, proliferation and calcification of MC3T3E1 cells were evaluated on the treated titanium surface. The treated titanium screws were implanted into rat tibias and the removal torques were measured 28 days post-surgery. The titanium surface that underwent the combination treatment exhibited recovery of biocompatibility by allowing cellular proliferation or calcification at levels observed in the non-infected titanium surfaces. The removal torque 28 days after surgery was also comparable to the control values. This approach is a novel treatment option for peri-implantitis.

Oral mucosal irritation potential of antimicrobial chemotherapy involving hydrogen peroxide photolysis with high-power laser irradiation for the treatment of periodontitis.

In the present study, we assessed the oral mucosal irritation potential of antimicrobial chemotherapy involving hydrogen peroxide (H2O2) photolysis with a 405-nm laser device at an output power of ≥100 mW in hamsters. Twenty-four cheek pouches from 12 male Syrian hamsters received 7-min treatment with pure water (PW), 3% H2O2, laser irradiation of PW at 100 mW, laser irradiation of 3% H2O2 at 100 mW, laser irradiation of PW at 200 mW, or laser irradiation of 3% H2O2 at 200 mW (n = 4 each). The diameter of the irradiation area was set at 3 mm; accordingly, the calculated irradiances (optical power densities) of the 100- and 200-mW laser lights were approximately 1400 and 2800 mW/cm2, respectively. In addition, 12 cheek pouches from six animals received laser irradiation of 3% H2O2 at 100 mW for 1, 3, or 5 min (n = 4 each). Each treatment was repeated three times at 1-h intervals. Macroscopic and histological changes were evaluated 24 h after the last treatment. In addition, in vitro bactericidal activity of the treatment against periodontal pathogens was evaluated. We found that 405-nm laser irradiation of 3% H2O2 caused moderate to severe oral mucosal irritation when performed at powers of 100 and 200 mW for ≥3 min, while the same treatment performed at 100 mW for 1 min resulted in mild irritation. Moreover, 1-min H2O2 photolysis at 100 mW caused a >4-log decrease in viable bacterial counts. These findings suggest that 1-min H2O2 photolysis, which can effectively kill periodontal pathogens, may be acceptable when a 405-nm laser device is used at 100 mW. However, use of the laser at a lower power would be preferable for the prevention of unnecessary oral mucosal irritation.

Features of high flow access in the elderly.

INTRODUCTION: The number of elderly hemodialysis patients continues to grow. The aim of this study was to investigate differences in elderly high flow access patients compared with middle-aged and young patients. METHODS: We performed a retrospective study to determine the characteristics of elderly patients (aged >60 years) following blood flow suppression procedures. Preoperative and postoperative data from 177 patients who underwent blood flow suppression procedures and 73 patients who underwent procedures for run-off vein ligation and subcutaneous fixation of the superficial artery were compared. RESULTS: A high proportion of young (aged 20-40 years) and middle-aged (aged 41-60 years) patients met the criteria for blood flow suppression procedures (flow volume 1500 mL/min, flow volume/cardiac output 35%), whereas a high proportion of elderly patients did not. Moreover, heart strain could evidently be caused even with low flow volume. In elderly patients, a tricuspid regurgitation pressure gradient and right heart strain were observed more frequently. CONCLUSION: Elderly patients who underwent blood flow suppression procedures or subcutaneous fixation of the superficial artery exhibited lower flow volume, and the effects of high flow access in elderly patients depend on the nature of vascular changes. Ultimately, the underlying conditions and hemodynamics of each patient must be determined on an individual basis.

Hydroxyl radicals generated by hydrogen peroxide photolysis recondition biofilm-contaminated titanium surfaces for subsequent osteoblastic cell proliferation.

Titanium dental implants have been successfully used for decades; however, some implants are affected by peri-implantitis due to bacterial infection, resulting in loss of supporting bone. This study aimed to evaluate the effect of an antimicrobial chemotherapy employing H2O2 photolysis-developed to treat peri-implantitis-on biofilm-contaminated titanium surfaces in association with osteoblastic cell proliferation on the treated surface. Titanium discs were sandblasted and acid-etched, followed by contamination with a three-species biofilm composed of Porphyromonas gingivalis, Fusobacterium nucleatum, and Streptococcus mitis. This biofilm model was used as a simplified model of clinical peri-implantitis biofilm. The discs were subjected to ultrasound scaling, followed by H2O2 photolysis, wherein 365-nm LED irradiation of the disc immersed in 3% H2O2 was performed for 5 min. We analysed proliferation of mouse osteoblastic cells (MC3T3-E1) cultured on the treated discs. Compared with intact discs, biofilm contamination lowered cell proliferation on the specimen surface, whereas H2O2 photolysis recovered cell proliferation. Thus, H2O2 photolysis can recover the degraded biocompatibility of biofilm-contaminated titanium surfaces and can potentially be utilised for peri-implantitis treatment. However, to verify the findings of this study in relation to clinical settings, assessment using a more clinically relevant multi-species biofilm model is necessary.

Surface properties of dental zirconia ceramics affected by ultrasonic scaling and low-temperature degradation.

Zirconia (3Y-TZP) dental prostheses are widely used in clinical dentistry. However, the effect of ultrasonic scaling performed as a part of professional tooth cleaning on 3Y-TZP dental prostheses, especially in conjunction with low-temperature degradation (LTD), has not been fully investigated. The present study aimed to evaluate the influence of ultrasonic scaling and LTD on the surface properties of 3Y-TZP in relation to bacterial adhesion on the treated surface. 3Y-TZP specimens (4 × 4 × 2 mm) were polished and then subjected to autoclaving at 134°C for 100 h to induce LTD, followed by 10 rounds of ultrasonic scaling using a steel scaler tip for 1 min each. Surface roughness, crystalline structure, wettability, and hardness were analyzed by optical interferometry, X-ray diffraction analysis, contact angle measurement, and nano-indentation technique, respectively. Subsequently, bacterial adhesion onto the treated 3Y-TZP surface was evaluated using Streptococcus mitis and S. oralis. The results demonstrated that the combination of ultrasonic scaling and LTD significantly increased the Sa value (surface roughness parameter) of the polished 3Y-TZP surface from 1.6 nm to 117 nm. LTD affected the crystalline structure, causing phase transformation from the tetragonal to the monoclinic phase, and decreased both the contact angle and surface hardness. However, bacterial adhesion was not influenced by these changes in surface properties. The present study suggests that ultrasonic scaling may be acceptable for debridement of 3Y-TZP dental prostheses because it did not facilitate bacterial adhesion even in the combination with LTD, although it did cause slight roughening of the surface.

Potential adverse effects of antimicrobial chemotherapy based on ultraviolet-A irradiation of polyphenols against the oral mucosa in hamsters and wounded skin in rats.

Antimicrobial chemotherapy based on ultraviolet-A (UVA) irradiation of polyphenol solution has been proposed as an adjunctive treatment for dental caries. However, the safety of this treatment has not been thoroughly evaluated. Therefore, the aim of the present study was to assess the influence of this treatment on the oral mucosa in hamsters and wounded skin in rats. An oral mucosal irritation test was performed in hamsters. The cheek pouch was everted and treated with UVA irradiation (wavelength: 365 nm) of pure water, 1 mg/mL of caffeic acid, or 1 mg/mL of grape seed extract using a light-emitting diode at an irradiance of 275 mW/cm2. Each treatment was performed for 2 or 5 min and repeated three times. Macroscopic and histological evaluations were performed 24 h after the last treatment. We also examined the effects of the treatment on the healing process of skin wounds in rats. Full-thickness skin wounds created on the back of the rats were treated for 2 min as described above, but only once. The wound area was then assessed daily for 9 days. The results demonstrated that the treatment induced oral mucosal irritation depending on the irradiation time; however, it did not influence the wound healing process. The oral mucosal irritation potential of three treatment sessions performed for 2 and 5 min was minimal and mild to moderate, respectively, according to histological analysis. These findings suggest that the duration of treatment based on UVA irradiation of polyphenols in the oral cavity should be as short as possible, considering the clinical efficacy of the antimicrobial effects and the irritation potential.

Critical considerations on load-to-failure test for monolithic zirconia molar crowns.

Application of monolithic zirconia crowns (MZCs) with reduced thickness to the molar region has been proposed, but potential complications have yet to be fully evaluated in laboratory tests. The present study aimed to develop a clinically relevant load-to-failure test in combination with fatigue treatments involving thermal and mechanical cycling (TC and MC) to evaluate the fracture resistance of molar MZCs. MZCs with a minimal thickness of 0.5 mm were bonded to dies made of resin-based composite (RBC), epoxy resin (EP), or polyoxymethylene-copolymer (POM-C). The samples were either untreated (UT) or subjected to TC (5-55 °C for 1â€¯× 105 cycles) and MC (300 N for 2.4â€¯× 106 cycles). The stress generated by TC and MC was simulated by finite element modeling. The load-to-failure test was performed using an inverse V-shaped two-plane indenter and was followed by fractographic analysis. The median values of fracture load for MZC/RBC and MZC/EP in the TC group were significantly lower than those in the UT group. MC also decreased the median value of fracture load for MZC/RBC significantly, but not that for MZC/EP and MZC/POM-C. Fractography revealed that the fracture started in the cervical area in all groups, which is similar to clinically failed crowns. The simulation confirmed stress concentration at the cervical area in both TC and MC groups. The present study suggests that the load-to-failure test using a two-plane indenter could induce clinically relevant fracture of MZCs, the vulnerability of the MZCs depends largely on the die material employed, and MZCs are more likely to be damaged by thermal fatigue than mechanical fatigue.

A novel pathway for the photooxidation of catechin in relation to its prooxidative activity.

In the present study, we evaluated the prooxidative mode of action of photoirradiated (+)-catechin at 400 nm in relation to reactive oxygen species generation and its possible application to disinfection. Photoirradiation of (+)-catechin at a concentration of 1 mg/mL yielded not only hydrogen peroxide (H2O2) but hydroxyl radical (·OH) in a total amount of approximately 20 µM in 10 min. As a result, photoirradiated catechin killed Staphylococcus aureus, and a > 5-log reduction in viable bacteria counts was observed within 20 min. Liquid chromatography-high-resolution-electrospray ionization-mass spectrometry showed that photoirradiation decreased the (+)-catechin peak (molecular formula C15H14O6) whilst it increased two peaks of a substance with the molecular formula C15H12O6 with increasing irradiation time. Nuclear magnetic resonance analysis revealed that the two C15H12O6 peaks were allocated to intramolecular cyclization products that are enantiomers of each other. These results suggest that photoirradiation induces oxidation of (+)-catechin resulting in the reduction of oxygen to generate H2O2. This H2O2 is then homolytically cleaved to ·OH, and alongside this process, (+)-catechin is finally converted to two intramolecular cyclization products that are different from the quinone structure of the B ring, as proposed previously for the autoxidation and enzymatic oxidation of catechins.

Influence of microscale expansion and contraction caused by thermal and mechanical fatigue on retentive strength of CAD/CAM-generated resin-based composite crowns.

CAD/CAM-generated resin-based composite crowns have been proposed as an inexpensive alternative to conventional crowns. However, concerns have been raised about crown loosening in clinical use. Therefore, the present in vitro study aimed to evaluate the influence of thermal and mechanical cycling (TC and MC) on retentive strength of CAD/CAM resin-based crowns in relation to microscale expansion and contraction caused by fatigue. Eighty standardized dies were produced using a resin-based composite material. Crowns were milled from resin-based composite (n = 40) and glass-ceramic blocks (n = 40; control) using a dental CAD/CAM system. The crowns bonded to the dies were subjected to TC (temperature: 5 and 55 °C, cycles: 50,000) and MC (load: 200 N, cycles: 1.2 million). After fatigue treatment, retentive strength of the crowns was evaluated by a crown pull-off test at a crosshead speed of 1 mm/min. Coefficient of thermal expansion (CTE) and modulus of elasticity (E-modulus) of each material were also analyzed to estimate the microscale expansion and contraction during TC and MC. TC and MC significantly reduced the retentive strength of the CAD/CAM resin-based crowns whereas that of the CAD/CAM ceramic crowns was only affected by TC. In addition, the resin-based crowns showed a higher number of crown loosening during TC than the ceramic crowns. Analyses of CTE and E-modulus indicated that the resin-based crowns would be more deformed during TC and MC than the ceramic crowns. The present study demonstrated that the resistance of crowns to microscale expansion and contraction caused by thermal and mechanical fatigue would play an important role in maintaining retentive strength.

Proanthocyanidin-Rich Grape Seed Extract Modulates Intestinal Microbiota in Ovariectomized Mice.

Grape-seed extract (GSE) is rich in proanthocyanidins (polymers of flavan-3-ols). GSE is well known to have various beneficial effects to health. The objective of this study was to examine the effect of dietary GSE on the intestinal microbiota in ovariectomized (OVX) mice as a model of menopause. Phylum-level analyses using 16S rRNA-targeted group-specific polymerase-chain reaction primers in fecal samples collected 8 weeks postoperatively from OVX mice revealed that the proportion of Firmicutes and Bacteroidetes populations became imbalanced as compared with that in sham-operated control mice. That is, the ratio of Firmicutes:Bacteroidetes populations in the OVX group were increased significantly. When OVX animals were given dietary GSE, the imbalanced proportion of Firmicutes and Bacteroidetes populations was normalized to that seen in control mice. In addition, the body weight of OVX animals measured at 6 weeks postoperatively was significantly higher than that in sham-operated control animals. Dietary GSE also prevented OVX animals from increasing body weight. Thus, we postulated that GSE can improve imbalanced populations of intestinal microbiota, leading to prevention of obesity under conditions of not only menopause but morbidity. PRACTICAL APPLICATION: The GSE has a great potential to be a functional food to improve dysbiosis in post-menopausal women.