Optimizing twin-screw melt granulation: The role of overflight clearance on granulation behavior.

Twin-screw melt granulation (TSMG) relies on the dispersive and distributive mixing at the kneading zone for granule growth to happen highlighting the critical role played by the kneading elements in TSMG. Despite extensive research conducted on the impact of screw geometry in melt compounding, there is not enough literature for TSMG. Disc width for the kneading elements was 2 mm, contrary to the standard 5 mm. The objective of this study was to evaluate if varying overflight clearance (OC) can alter the paradigm for TSMG. The new elements reduce the peak shear at kneading zone however a higher barrel temperature and degree of fill (DoF) is required to compensate to attain similar granule attributes. The change in DoF was achieved through a combination of modified screw configuration to pre-densify powders before kneading and processing at a lower screw speed. Despite the higher barrel temperature, process optimization of thermally unstable gabapentin was carried out. Using the new elements, compressible granules (Tensile strength > 2 MPa) with low % GABA-L content were manufactured despite increasing OC to 0.4 mm. Granule stability at 40 °C, ambient humidity for 6 months indicated gabapentin was stable (% GABA-L ≪0.4 %) despite a high barrel temperature of 120 °C.

Taste masking and rheology improvement of drug complexed with beta-cyclodextrin and hydroxypropyl-ß-cyclodextrin by hot-melt extrusion.

This study aimed to mask fluconazole (FLU) taste and improve its rheological properties by an efficient process of cyclodextrin complexation. For this, hot-melt extrusion (HME) was used to obtain extrudates composed of FLU, hydroxypropylcellulose, and one of two different cyclodextrins (ß-cyclodextrin or hydroxypropyl-ß-cyclodextrin) maintaining the drug:cyclodextrin molar ratio at 1:0.3 or 1:0.2, respectively. Samples were characterized by physicochemical tests, palatability using e-tongue and antifungal assays. Drug stability was preserved after HME, according to spectroscopy test (correlation coefficient >0.9) and HPLC-assay (100-107%). Flowability was improved in HME systems with compressibility of <12%. Similarly, floodability exhibited significant enhancement (dispersibility <10%). Whereas extrudates of FLU containing only the polymeric matrix led to a slow drug dissolution efficiency (18.6%) and a partial drug taste masking; extrudates containing cyclodextrin accelerated FLU dissolution (dissolution efficiency approx. 30%) and provided a complete drug taste masking. Moreover, HME process could produce drug complexes with high complexation efficiency and preserve its antifungal activity.

Hot Melt Extrudates Formulated Using Design Space: One Simple Process for Both Palatability and Dissolution Rate Improvement.

This work aimed at obtaining an optimized itraconazole (ITZ) solid oral formulation in terms of palatability and dissolution rate by combining different polymers using hot melt extrusion (HME), according to a simplex centroid mixture design. For this, the polymers Plasdone® (poly(1-vinylpyrrolidone-co-vinyl acetate) [PVP/VA]), Klucel® ELF (2-hydroxypropyl ether cellulose [HPC]), and Soluplus® (SOL, polyvinyl caprolactam-polyvinyl acetate-polyethylene glycol) were processed using a laboratory HME equipment operating without recirculation at constant temperature. Samples were characterized by physicochemical assays, as well as dissolution rate and palatability using an e-tongue. All materials became homogeneous and dense after HME processing. Thermal and structural analyses demonstrated drug amorphization, whereas IR spectroscopy evidenced drug stability and drug-excipient interactions in HME systems. Extrudates presented a significant increase in dissolution rate compared to ITZ raw material, mainly with formulations containing PVP/VA and HPC. A pronounced improvement in taste masking was also identified for HME systems, especially in those containing higher amounts of SOL and HPC. Data showed polymers act synergistically favoring formulation functional properties. Predicted best formulation should contain ITZ 25.0%, SOL 33.2%, HPC 28.9%, and PVP/VA 12.9% (w/w). Optimized response considering dissolution rate and palatability reinforces the benefit of polymer combinations.

Investigate the effect of solvents on wet granulation of microcrystalline cellulose using hydroxypropyl methylcellulose as a binder and evaluation of rheological and thermal characteristics of granules.

Wet granulation is the most commonly used technique in the pharmaceutical industry for delivering oral solid dosage forms. In wet granulation, the binder solvent is one of the critical factors affecting granule properties. In the current study, an attempt was made to investigate the effect of solvents (aqueous and hydro-alcoholic) on thermal and flow properties of Microcrystalline Cellulose (MCC) granules prepared using two different grades of Hydroxypropyl Methylcellulose (HPMC), which served as an effective binder. The granulation endpoint was evaluated using thermal effusivity sensor. Rheometer and Modulated Differential Scanning Calorimetry (mDSC) was used to study the flow and thermal properties of wet and dried granules. Furthermore, physical characterization was carried out by granule strength, particle size distribution and tablet hardness for all granules under the study. Thermal effusivity sensor results indicate 55% w/w concentration of binder solution as the endpoint by measuring thermal effusivity for both binders. Additionally, powder rheometer results show that the wet granules of hydro-alcoholic batches show greater resistance to flow whereas the dried granules display excellent flow characteristics as evident from Basic flowability energy values and specific energy values. Permeability results suggest that the granules formed with hydro-alcoholic binder solvent exhibit better porosity and permeability. Tablet hardness data showed that tablets formulated using hydro-alcoholic solvent granules have greater hardness than tablets formulated using water based solvent granules. The granule strength for water based granules is relatively higher than that of hydro-alcoholic based granules. mDSC thermograms show a sharp rise in enthalpy value at 55% w/w binder solution which is indicative of a more significant amount of solvent being present on the surface of granules and formation of optimal granules. To summarize, we have determined a technique to measure endpoint determination and simultaneously investigate the role of solvent systems on the rheology of MCC granules, which could assist in selecting an appropriate solvent system for granulation.

Development and evaluation of a dimensionless mechanistic pan coating model for the prediction of coated tablet appearance.

A mathematical, mechanistic tablet film-coating model has been developed for pharmaceutical pan coating systems based on the mechanisms of atomisation, tablet bed movement and droplet drying with the main purpose of predicting tablet appearance quality. Two dimensionless quantities were used to characterise the product properties and operating parameters: the dimensionless Spray Flux (relating to area coverage of the spray droplets) and the Niblett Number (relating to the time available for drying of coating droplets). The Niblett Number is the ratio between the time a droplet needs to dry under given thermodynamic conditions and the time available for the droplet while on the surface of the tablet bed. The time available for drying on the tablet bed surface is critical for appearance quality. These two dimensionless quantities were used to select process parameters for a set of 22 coating experiments, performed over a wide range of multivariate process parameters. The dimensionless Regime Map created can be used to visualise the effect of interacting process parameters on overall tablet appearance quality and defects such as picking and logo bridging.