Enhancement of Benzene Emissions in Special Combinations of Electronic Nicotine Delivery System Liquid Mixtures.

Electronic nicotine delivery systems (ENDS) are battery-powered devices introduced to the market as safer alternatives to combustible cigarettes. Upon heating the electronic liquid (e-liquid), aerosols are released, including several toxicants, such as volatile organic compounds (VOCs). Benzene has been given great attention as a major component of the VOCs group as it increases cancer risk upon inhalation. In this study, several basic e-liquids were tested for benzene emissions. The Aerosol Lab Vaping Instrument was used to generate aerosols from ENDS composed of different e-liquid combinations: vegetable glycerin (VG), propylene glycol (PG), nicotine (nic), and benzoic acid (BA). The tested mixtures included PG, PG + nic + BA, VG, VG + nic + BA, 30/70 PG/VG, and 30/70 PG/VG + nic + BA. A carboxen polydimethylsiloxane fiber for a solid-phase microextraction was placed in a gas cell to trap benzene emitted from a Sub-Ohm Minibox C device. Benzene was adsorbed on the fiber during the puffing process and for an extra 15 min until it reached equilibrium, and then it was determined using gas chromatography-mass spectrometry. Benzene was quantified in VG but not in PG or the 30/70 PG/VG mixtures. However, benzene concentration increased in all tested mixtures upon the addition of nicotine benzoate salt. Interestingly, benzene was emitted at the highest concentration when BA was added to PG. However, lower concentrations were found in the 30/70 PG/VG and VG mixtures with BA. Both VG and BA are sources of benzene. Enhanced emissions, however, are mostly noticeable when BA is mixed with PG and not VG.

Influence of nicotine form and nicotine flux on puffing behavior and mouth-level exposure to nicotine from electronic nicotine delivery systems.

BACKGROUND: Nicotine form (freebase/protonated) and nicotine flux (rate at which nicotine is emitted) are two factors that can affect the dose of nicotine inhaled by individuals using electronic nicotine delivery systems (ENDS) because they can influence puffing behavior. The nicotine dose for each puff also is directly proportional to nicotine flux (i.e., dose/puff=nicotine flux*puff duration). This study examines the effect of nicotine form and flux on puffing parameters and mouth-level nicotine exposure. METHODS: Thirty-two dual ENDS and combustible cigarette participants completed five visits that differed by nicotine form (freebase or protonated) and nicotine flux (14 or 35µg/sec); a zero-nicotine condition was a negative control. Participants used a Subox Mini C ENDS, powered at 20W, during a 10-puff directed bout (B1) followed by a one-hour ad libitum bout (B2). Puffing parameters and mouth-level nicotine exposure were assessed using the American University of Beirut REALTIME instrument. RESULTS: Relative to protonated nicotine, freebase nicotine was associated with lower total puff duration (puff duration*number of puffs), lower flow rate in B1, lower liquid consumption, and lower mouth-level nicotine exposure. Increasing nicotine flux from 14 to 35µg/sec was associated with lower total puff duration in both bouts, as well as lower liquid consumption. Increasing nicotine flux was associated with higher mouth-level nicotine exposure in B1 only. CONCLUSION: ENDS with protonated nicotine may enhance nicotine exposure by promoting longer puffing and thus greater dose delivered. This work highlights the importance of accounting for interactions between nicotine form and flux when considering nicotine regulation for ENDS.

Effects of Aftermarket Electronic Cigarette Pods on Device Power Output and Nicotine, Carbonyl, and ROS Emissions.

Aftermarket pods designed to operate with prevalent electronic nicotine delivery system (ENDS) products such as JUUL are marketed as low-cost alternatives that allow the use of banned flavored liquids. Subtle differences in the design or construction of aftermarket pods may intrinsically modify the performance of the ENDS device and the resulting nicotine and toxicant emissions relative to the original equipment manufacturer's product. In this study, we examined the electrical output of a JUUL battery and the aerosol emissions when four different brands of aftermarket pods filled with an analytical-grade mixture of propylene glycol, glycerol, and nicotine were attached to it and puffed by machine. The aerosol emissions examined included total particulate matter (TPM), nicotine, carbonyl compounds (CCs), and reactive oxygen species (ROS). We also compared the puff-resolved power and TPM outputs of JUUL and aftermarket pods. We found that all aftermarket pods drew significantly greater electrical power from the JUUL battery during puffing and had different electrical resistances and resistivity. In addition, unlike the case with the original pods, we found that with the aftermarket pods, the power provided by the battery did not vary greatly with flow rate or puff number, suggesting impairment of the temperature control circuitry of the JUUL device when used with the aftermarket pods. The greater power output with the aftermarket pods resulted in up to three times greater aerosol and nicotine output than the original product. ROS and CC emissions varied widely across brands. These results highlight that the use of aftermarket pods can greatly modify the performance and emissions of ENDS. Consumers and public health authorities should be made aware of the potential increase in the level of toxicant exposure when aftermarket pods are employed.

Nicotine flux as a powerful tool for regulating nicotine delivery from e-cigarettes: Protocol of two complimentary randomized crossover clinical trials.

INTRODUCTION: Electronic cigarette (EC) use has increased rapidly in the last decade, especially among youth. Regulating nicotine delivery from ECs could help curb youth uptake and leverage EC use in harm reduction yet is complicated by varying device and liquid variables that affect nicotine delivery. Nicotine flux, the nicotine emission rate, is a parameter that incorporates these variables and focuses on the performance rather than the design of an EC. Nicotine flux therefore could be a powerful regulatory tool if it is shown empirically to predict nicotine delivery and subjective effects related to dependence. METHODS AND ANALYSIS: This project consists of two complementary clinical trials. In Trial I, we will examine the relationship between nicotine flux and the rate and dose of nicotine delivery from ECs, hence, impacting abuse liability. It will also examine the extent to which this relationship is mediated by nicotine form (i.e., freebase versus protonated). At Yale School of Medicine (YSM), study participants will puff EC devices under conditions that differ by flux and form, while arterial blood is sampled in high time resolution. In Trial II, we will assess the relationship between nicotine flux, form, and subjective effects. At the American University of Beirut (AUB), participants will use EC devices with varying nicotine fluxes and forms, while dependency measures, such as the urge to use ECs, nicotine craving, and withdrawal symptoms, will be assessed. We will also monitor puffing intensity and real-time exposure to toxicants. ETHICS AND DISSEMINATION: The protocol of Trial I and Trial II was approved by YSM and AUB IRBs, respectively. We will disseminate study results through peer-reviewed publications and conference presentations. TRIAL REGISTRATION: NCT05706701 for Trial I and NCT05430334 for Trial II.

The impact of vaping ethanol-containing electronic cigarette liquids on roadside impairment investigations.

Legal professionals and others have suggested that vaping electronic cigarettes (e-cigs) prior to or during ethanol breath testing may produce false positives. Preliminary breath tests (PBTs) and evidentiary breath tests (EBTs) measure ethanol in exhaled breath and standardized field sobriety tests (SFSTs) are used to assess impairment. Ethanol has been identified in e-cig liquids (e-liquids). Presented are a series of experiments designed to determine the mechanics of vaping ethanol using an e-cig and the effects of vaping ethanol on the SFSTs and breath tests used by law enforcement officers (LEO). Twelve participants (five females, age: 21-32 and seven males, age: 21-55), vaped either one or ten puffs of an e-liquid (0% or 20% ethanol). LEOs assessed impairment using SFSTs (12 and 42 min), PBTs (<1, 27, 32, 37 and 57 min) and EBTs (2, 29, 34, 39 and 59 min) post-vaping. A self-assessment test was administered post-vaping (22 and 52 min). Baseline responses for all measures were collected prior to vaping. Results demonstrated that ethanol in the e-liquids was aerosolized by e-cigs and produced particles that could reach the deep lung tissue based on mean-mass diameter. Ethanol was detected by PBT <3 min after participants vaped one (0.007-0.030 g/210 L) or ten puffs (013-0.074 g/210 L) of a 20% ethanol e-liquid. Ethanol was not detected by PBT at any subsequent time point. Ethanol was not detected by the EBT under any condition. Impairment was not indicated by the SFST. Some subjective effects were reported, but few statistically significant differences between conditions were indicated. A wait period prior to ethanol breath testing is not always mandated, depending on jurisdiction, or observed in all applications, such as workplace testing. The results demonstrate that a wait period must be employed to prevent vaping-related false-positive breath ethanol results.

Comparison of design characteristics and toxicant emissions from Vuse Solo and Alto electronic nicotine delivery systems.

INTRODUCTION: Vuse Solo is the first electronic nicotine delivery system (ENDS) authorised by the US Food and Drug Administration for marketing in the USA. Salient features of the Vuse Solo product such as nicotine form, draw resistance, power regulation and electrical characteristics have not been reported previously, and few studies have examined the nicotine and other toxicant emissions of this product. We investigated the design characteristics and toxicant emissions of the Solo as well as Alto, another Vuse product with a greater market share than Solo. METHODS: Total/freebase nicotine, propylene glycol to vegetable glycerin ratio, carbonyl compounds (CC) and reactive oxygen species (ROS) were quantified by gas chromatography, high-performance liquid chromatography and fluorescence from aerosol emissions generated in 15 puffs of 4 s duration. The electric power control system was also analysed. RESULTS: The average power delivered was 2.1 W and 3.9 W for Solo and Alto; neither system was temperature-controlled. Vuse Solo and Alto, respectively, emitted nicotine at a rate of 38 µg/s and 115 µg/s, predominantly in the protonated form (>90%). Alto's ROS yield was similar to a combustible cigarette and one order of magnitude greater than that of Solo. Total carbonyls from both products were two orders of magnitude lower than combustible cigarettes. CONCLUSION: Vuse Solo is an above-Ohm ENDS that emits approximately one-third the nicotine flux of a Marlboro Red cigarette (129 µg/s) and considerably lower CC and ROS yields than a combustible cigarette. With its higher power, the nicotine flux and ROS yield from Alto are similar to Marlboro Red levels; Alto may thus present greater abuse liability than the lower sales-volume Solo.

The Substitution of Fifty Percent of Combustible Tobacco Smoke Exposure With Either Electronic Cigarettes or Heated tobacco Products Did Not Attenuate Acute Lung Injury in an Animal Model.

BACKGROUND: To reduce the harmful health effects of combustible cigarette smoke (CS), some (CS) users attempt to substitute CS with electronic cigarettes (ECIG) and/or heated tobacco products (HTP). In this animal study, we evaluated the acute effects of substituting CS consumption with ECIG or HTP thus mimicking the dual users' approach, on the lungs of a mouse model. METHODS: C57BL/6 mice were divided into Control, ECIG, HTP, CS, ECIG + CS, HTP + CS, and HTP + ECIG groups. Animals were exposed for 3 hours in AM and PM sessions to either air, CS, ECIG, or HTP for seven days. Lung injury was assessed by: wet to dry (W/D) ratio, albumin concentration in bronchoalveolar lavage fluid, expression of IL-1ß, IL-6, and TNF-α, histopathology examination, reactive oxygen species (ROS) production, and assessment of cellular apoptosis. RESULTS: W/D ratio was significantly increased in mice exposed to CS only. Albumin leak and expression of IL-1ß, IL-6, and TNF-a were elevated in CS, ECIG + CS, and HTP + CS. Histological examination revealed significant inflammatory cells infiltration, as well as collagen deposit in CS, ECIG + CS, HTP + CS. ROS production was significantly increased in CS, ECIG + CS, HTP + CS. Finally, cell death was also significantly increased in CS, ECIG + CS, and HTP + CS. CONCLUSION: In this animal model, substituting 50% of daily CS exposure by either ECIG or HTP exposure did not result in significant attenuation of acute lung injury.

Carbonyl Emissions and Heating Temperatures across 75 Nominally Identical Electronic Nicotine Delivery System Products: Do Manufacturing Variations Drive Pulmonary Toxicant Exposure?

Studies of factors that impact electronic nicotine delivery systems (ENDSs) carbonyl compound (CC) emissions have been hampered by wide within-condition variability. In this study, we examined whether this variability may be related to heating coil temperature variations stemming from manufacturing differences. We determined the mean peak temperature rise (ΔTmax) and CC emissions from 75 Subox ENDSs powered at 30 W. We found that ΔTmax and CC emissions varied widely, with greater ΔTmax resulting in exponentially higher CC emissions. Also, 12% of atomizers accounted for 85% of total formaldehyde emissions. These findings suggest that major reductions in toxicant exposure might be achieved through regulations focusing on limiting coil temperature.

Impact of smoking intensity and device cleaning on IQOS emissions: comparison with an array of cigarettes.

SIGNIFICANCE: IQOS is a heated tobacco product that has been widely advertised by Philip Morris International (PMI) as a reduced-exposure product compared with cigarettes. Reduced exposure results from reduced emission of toxicants which could be influenced by product constituents and user behaviour. This study aims to assess the influence of user behaviour, including device cleaning and puffing parameters, on toxicant emissions from IQOS. METHODS: IQOS aerosols were generated by a smoking machine using the combination of two cleaning protocols (after 1 stick vs 20 sticks) and five puffing regimes (including standard cigarette puffing regimes and IQOS-tailored regimes). The generated aerosols were analysed by targeted methods for phenol and carbonyl quantification, and by chemical screening for the identification of unknown compounds. RESULTS: Puffing parameters significantly affected phenol and carbonyl emissions while device cleaning had no effect. Harsher puffing conditions like more, longer, and larger puffs yielded higher levels for most toxicant emissions. Comparing the obtained data with data reported by PMI on 50 cigarette brands smoked under different puffing regimes showed various trends for phenol and carbonyl emissions, with IQOS emissions sometimes higher than cigarettes. Also, the chemical screening resulted in the tentative identification of ~100 compounds in the IQOS aerosols (most of limited toxicity data). CONCLUSION: This study showed that puffing parameters, but not device cleaning, have significant effects on carbonyl, phenol and other emissions. Data analysis highlighted the importance of comparing IQOS emissions with an array of commercial cigarettes tested under different puffing regimes before accepting reduced exposure claims.

Interactive effects of protonated nicotine concentration and device power on ENDS nicotine delivery, puff topography, and subjective effects.

Electronic nicotine delivery systems (ENDSs) produce an aerosol by heating a liquid that often contains nicotine. The nicotine can be protonated that may make the aerosol easier to inhale than freebase nicotine. This study's purpose is to determine, in cigarette smokers and ENDS users, the effects of three concentrations of protonated nicotine aerosolized at two different power settings. Forty-five participants (22 cigarette smokers and 23 ENDS users) completed some or all of six sessions that varied by liquid nicotine concentration (10, 15, or 30 mg/ml protonated nicotine) and device power (15 or 30 W). Participants took 10 puffs from each product and then used each product for 90 min ad libitum. Plasma nicotine concentration, subjective effects, and puff topography were measured. Results showed increases in plasma nicotine concentration in all conditions, with greater plasma nicotine increases in higher watt, higher nicotine concentration conditions, as well as greater nicotine delivery for ENDS users compared to cigarette smokers. For puff topography, puff duration and volume decreased as nicotine concentration and power increased, and ENDS users took longer and larger puffs than cigarette smokers. Participants rated the higher watt, higher nicotine concentration conditions as harsher and with more throat hit. Overall, these results suggest that device characteristics and liquid constituents interact to influence users' plasma nicotine delivery and should be considered together when regulating ENDS. (PsycInfo Database Record (c) 2023 APA, all rights reserved).

Time course of changes in inflammatory and oxidative biomarkers in lung tissue of mice induced by exposure to electronic cigarette aerosol.

Significance: Electronic cigarettes (e-cigarettes) have become a popular way to smoke all over the world. Chronic exposure to e-cigarette aerosol may influence lung health. This study uses an animal model to explore the time course of the effect of exposure to e-cigarette aerosols on the lung. Methods: Lung samples were collected after exposure of Balb/c mice to e-cigarette aerosols for 1 h/day (6 times/week) for 1, 2 and 4 weeks and compared to sham-exposed controls. Examined biomarkers including inflammatory cells, tumor necrosis factor α (TNFα), interleukin-6 (IL-6), interleukin-10 (IL-10), reduced glutathione (GSH), oxidized glutathione (GSSG), glutathione peroxidase (GPx), catalase, superoxide dismutase (SOD), and Thiobarbituric acid reactive substances (TBARS). Results: Exposure of animals to e-cigarette aerosols induced significant increases (P < 0.05) in total inflammatory cells, eosinophils, macrophages and TNFα in the lung tissue after 1, 2 and 4 weeks of exposure. Furthermore, level of IL-10 significantly decreased, whereas levels of neutrophils and basophils significantly increased (P < 0.05) after 1 week of exposure. Exposure of animals to e-cigarette aerosol also induced significant decreases (P < 0.05) in the GSH/GSSG ratio, and GPx levels after 2 and 4 weeks of exposures. The activity of catalase was also reduced (P < 0.05) after 4 weeks of exposure. Level of TBARS showed a trend of elevation with time and it reached a significant elevation after 4 weeks (P < 0.01). Conclusion: Current results indicate that inhalation of unflavored e-cigarette aerosol might be associated with inflammation in lung tissue that worsen as the duration of exposure increases. Further experiments including more time points, histopathology and pulmonary physiology experiments are needed to confirm the current results.

Assessing toxicant emissions from e-liquids with DIY additives used in response to a potential flavour ban in e-cigarettes.

SIGNIFICANCE: Electronic cigarettes (e-cigarettes) aerosolise liquids that contain nicotine, propylene glycol, glycerol and appealing flavours. In the USA, regulations have limited the availability of flavoured e-cigarettes in pod-based systems, and further tightening is expected. In response, some e-cigarette users may attempt to make their e-liquids (do-it-yourself, DIY). This study examined toxicant emissions from several aerosolised DIY e-liquids. METHODS: DIY additives were identified by reviewing users' responses to a hypothetical flavour ban, e-cigarette internet forums and DIY mixing internet websites. They include essential oils, cannabidiol, sucralose and ethyl maltol. E-liquids with varying concentrations and combinations of additives and tobacco and menthol flavours were prepared and were used to assess reactive oxygen species (ROS), carbonyl and phenol emissions in machine-generated aerosols. RESULTS: Data showed that adding DIY additives to unflavoured, menthol-flavoured or tobacco-flavoured e-liquids increases toxicant emissions to levels comparable with those from commercial flavoured e-liquids. Varying additive concentrations in e-liquids did not have a consistently significant effect on the tested emissions, yet increasing power yielded significantly higher ROS, carbonyl and phenol emissions for the same additive concentration. Adding nicotine to DIY e-liquids with sucralose yielded increase in some emissions and decrease in others, with freebase nicotine-containing e-liquid giving higher ROS emissions than that with nicotine salt. CONCLUSION: This study showed that DIY additives can impact aerosol toxicant emissions from e-cigarettes and should be considered by policymakers when restricting commercially available flavoured e-liquids.

Chronic Exposure to Waterpipe Smoke Elicits Immunomodulatory and Carcinogenic Effects in the Lung.

Effects of waterpipe smoking on lung pathobiology and carcinogenesis remain sparse despite the worldwide emergence of this tobacco vector. To address this gap, we investigated the effects of chronic waterpipe smoke (WPS) exposure on lung pathobiology, host immunity, and tumorigenesis using an experimental animal model that is prone to tobacco carcinogens and an exploratory observational analysis of human waterpipe smokers and nonsmokers. Mice exhibited elevated incidence of lung tumors following heavy WPS exposure (5 days/week for 20 weeks) compared to littermates with light WPS (once/week for 20 weeks) or control air. Lungs of mice exposed to heavy WPS showed augmented CD8+ and CD4+ T cell counts along with elevated protumor immune phenotypes including increased IL17A in T/B cells, PD-L1 on tumor and immune cells, and the proinflammatory cytokine IL1ß in myeloid cells. RNA-sequencing (RNA-seq) analysis showed reduced antitumor immune gene signatures in animals exposed to heavy WPS relative to control air. We also performed RNA-seq analysis of airway epithelia from bronchial brushings of cancer-free waterpipe smokers and nonsmokers undergoing diagnostic bronchoscopy. Transcriptomes of normal airway cells in waterpipe smokers, relative to waterpipe nonsmokers, harbored gene programs that were associated with poor clinical outcomes in patients with lung adenocarcinoma, alluding to a WPS-associated molecular injury, like that established in response to cigarette smoking. Our findings support the notion that WPS exhibits carcinogenic effects and constitutes a possible risk factor for lung cancer as well as warrant future studies that can guide evidence-based policies for mitigating waterpipe smoking. PREVENTION RELEVANCE: Potential carcinogenic effects of waterpipe smoking are very poorly understood despite its emergence as a socially acceptable form of smoking. Our work highlights carcinogenic effects of waterpipe smoking in the lung and, thus, accentuate the need for inclusion of individuals with exclusive waterpipe smoking in prevention and smoking cessation studies.

Low cost air quality sensors "PurpleAir" calibration and inter-calibration dataset in the context of Beirut, Lebanon.

The PurpleAir PA-II-SD is a low-cost particulate matter (PM2.5 and PM10) sensor that is currently available on the market. It is one of many such low-cost and commercially available particulate matter sensors which are being adopted by individuals and researchers worldwide. With growing use of these sensors, there is an interest in better understanding the performance and characteristics of these devices. Data was collected from twelve of these low-cost PurpleAir PA-II-SD sensors and two high fidelity Met One E-BAM PLUS instruments installed at a single location, on the campus of the American University of Beirut, in Beirut, Lebanon over a period of time from June 28, 2020 to September 30, 2020. The data was collected with the aim of assessing inter-sensor variability for the PurpleAir sensors and the sensor accuracy of the PurpleAir when compared to a high fidelity Met One E-BAM PLUS instrument.

Electrical features, liquid composition and toxicant emissions from 'pod-mod'-like disposable electronic cigarettes.

INTRODUCTION: Use of flavoured pod-mod-like disposable electronic cigarettes (e-cigarettes) has grown rapidly, particularly among cost-sensitive youth and young adults. To date, little is known about their design characteristics and toxicant emissions. In this study, we analysed the electrical and chemical characteristics and nicotine and pulmonary toxicant emission profiles of five commonly available flavoured disposable e-cigarettes and compared these data with those of a JUUL, a cartridge-based e-cigarette device that pod-mod-like disposables emulate in size and shape. METHODS: Device construction, electrical power and liquid composition were determined. Machine-generated aerosol emissions including particulate matter, nicotine, carbonyl compounds and heavy metals were also measured. Liquid and aerosol composition were measured by high-performance liquid chromatography, gas chromatography-mass spectrometry/flame ionisation detection, and inductively coupled plasma mass spectrometry. RESULTS: We found that unlike JUUL, disposable devices did not incorporate a microcontroller to regulate electrical power to the heating coil. Quality of construction varied widely. Disposable e-cigarette power ranged between 5 and 9 W and liquid nicotine concentration ranged between 53 and 85 mg/mL (~95% in the protonated form). In 15 puffs, total nicotine yield for the disposables ranged between 1.6 and 6.7 mg, total carbonyls ranged between 28 and 138 µg, and total metals ranged between 1084 and 5804 ng. JUUL emissions were near the floors of all of these ranges. CONCLUSIONS: Disposable e-cigarettes are designed with high nicotine concentration liquids and are capable of emitting much higher nicotine and carbonyl species relative to rechargeable look-alike e-cigarettes. These differences are likely due to the lower quality in construction, unreliable labelling and lack of temperature control regulation that limits the power during operation. From a public health perspective, regulating these devices is important to limit user exposure to carbonyls and nicotine, particularly because these devices are popular with youth and young adults.

Role of diabetes in lung injury from acute exposure to electronic cigarette, heated tobacco product, and combustible cigarette aerosols in an animal model.

BACKGROUND: Patients with diabetes are more vulnerable to the detrimental respiratory effects of combustible cigarette smoke (CS) when compared to the general population. Electronic cigarettes (ECIG) and heated tobacco products (HTP) are marketed as less harmful alternatives to CS. In this study, we compared the effects of acute ECIG, HTP and CS exposure on the lungs of type II diabetes versus non-diabetic mice in an animal model. METHODS: Type II Diabetic (Diab) and Non-Diabetic (Non-Diab) mice were divided into Control, ECIG, HTP and CS groups. Animals were exposed for 6 hrs./day to either air, ECIG, HTP or CS for seven days. Lung injury was determined by a) histopathology, b) wet to dry ratio, c) albumin concentration in bronchoalveolar lavage fluid, d) expression of TNF-α, IL-6, and IL-1 ß, e) reactive oxygen species production (ROS), and f) assessment of cellular apoptosis. RESULTS: Lung histology revealed increased edema and inflammatory cells in diabetic mice exposed to ECIG, HTP and CS. The expression of Inflammatory mediators was, in general, more significant in the Diabetic groups as well. TNF-α expression, for example, was upregulated in Diab + ECIG but not in Non-Diab + ECIG. ROS was significantly increased in Diab + CS, less in Non-Diab + CS and weakly noted in ECIG + Diab. Significant albumin leak was observed in Diab and Non-Diab HTP-exposed animals. CS exposure worsened lung injury in Diab when compared to Non-Diab mice. CONCLUSION: Comorbid medical conditions like diabetes may amplify ill effects of CS, ECIG or HTP exposure.

The effect of electronic cigarettes exposure on learning and memory functions: behavioral and molecular analysis.

Objective: Electronic cigarettes (ECIGs) are battery-powered devices that emit vaporized solutions for the user to inhale. ECIGs are marketed as a less harmful alternative to combustible cigarettes. The current study examined the effects of ECIG aerosol exposure on learning and memory, expression of brain derived neurotrophic factor (BDNF), and the activity of antioxidant enzymes in the hippocampus.Methods: Male Wistar rats were exposed to ECIG aerosol, by a whole-body exposure system, 1 h/day for 1 week, 4 weeks, and 12 weeks. Spatial learning and memory were tested using the Radial Arm Water Maze (RAWM). Hippocampal BDNF protein level, and oxidative stress biomarkers (GPx, SOD, GSH, GSSG, GSH/GSSG ratio) were also assessed.Results: ECIG aerosol exposure for 4 and 12 weeks impaired both short- and long- term memory and induced reductions in the hippocampus BDNF, SOD and GPx activities, and GSH/GSSG ratio (p < 0.05). No changes in any examined biomarkers were observed after 1-week exposure to ECIG aerosol (p > 0.05).Conclusions: ECIG aerosol exposure impaired functional memory and elicited changes in brain chemistry that are consistent with reduced function and oxidative stress.

JUUL 'new technology' pods exhibit greater electrical power and nicotine output than previous devices.

In 2019, JUUL Labs began marketing in the European Union 'new technology' pods that incorporated a new wick that it claimed provided 'more satisfaction'. In this study, we compared design and materials of construction, electrical characteristics, liquid composition and nicotine and carbonyl emissions of new technology JUUL pods to their predecessors. Consistent with manufacturer's claims, we found that the new pods incorporated a different wicking material. However, we also found that the new pod design resulted in 50% greater nicotine emissions per puff than its predecessor, despite exhibiting unchanged liquid composition, device geometry and heating coil resistance. We found that when connected to the new technology pods, the JUUL power unit delivered a more consistent voltage to the heating coil. This behaviour suggests that the new coil-wick system resulted in better surface contact between the liquid and the temperature-regulated heating coil. Total carbonyl emissions did not differ across pod generations. That nicotine yields can be greatly altered with a simple substitution of wick material underscores the fragility of regulatory approaches that centre on product design rather than product performance specifications.

Carrier Solvents of Electronic Nicotine Delivery Systems Alter Pulmonary Surfactant.

In late 2019, hundreds of users of electronic products that aerosolize a liquid for inhalation were hospitalized with a variety of respiratory and gastrointestinal symptoms. While some investigations have attributed the disease to the presence of vitamin E acetate in liquids that also contained tetrahydrocannabinol, some evidence suggests that chronic inhalation of two common solvents used in electronic nicotine delivery systems (ENDS), propylene glycol (PG) and vegetable glycerin (VG), can interfere with the lipid components of pulmonary surfactant and cause or exacerbate pulmonary injury. The interaction between PG, VG, and lung surfactant is not yet understood. This study presents an examination of the molecular interactions of PG and VG with lung surfactant mimicked by 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC). The interaction of DPPC and PG-VG is studied by attenuated total reflectance fourier transform infrared spectroscopy. The results showed that PG and VG altered the molecular alignment of the DPPC surfactant. The orientation of the surfactant at the surface of the lung affects the surface tension at the air-water interface, thereby influencing breathing. These findings suggest that chronic aerosolization of the primary solvents in ENDS might alter the function of pulmonary surfactant.