A Quantitative Assessment to Compare the Dimensions of the Alveolar Ridge Width Using Different Techniques for Implant Placement.

BACKGROUND: The success of any dental implant surgery depends on the correct diagnosis and treatment planning. PURPOSE: The aim of this study was to compare the dimensions of the alveolar ridge width using different techniques for implant placement. MATERIALS AND METHODS: The study involved 27 partially edentulous subjects aged 18-50, including males and females. In this study, the dimensions of the ridge were evaluated by ridge mapping on a cast, ridge mapping using a bone caliper, and ridge mapping with the help of an occlusal radiograph. All three methods were compared with ridge mapping by cone beam computed tomography (CBCT). For each subject, the site of implant placement was marked on the study model. Alveolar ridge measurement was done in the mouth by a bone caliper under local anesthesia with the help of a stent with a hole. Ridge mapping on a cast was done after sectioning the cast and marking with the help of a periodontal probe and stent. Ridge mapping was done on an occlusal radiograph by converting an acetate stent into a radiographic stent. Finally, CBCT was taken for each patient for ridge mapping. All four readings were tabulated. RESULTS: Comparing the mean alveolar ridge width of four groups, ANOVA showed significantly different alveolar ridge width among the groups (F=7.89, p<0.001). The validity (accuracy and precision) of ridge mapping on a cast, ridge mapping using a bone caliper, and occlusal radiograph against the CBCT (gold standard) was done using concordance correlation analysis. The concordance correlation analysis showed the highest association (ρ=0.8196) and precision (ϸ=82.61%) of ridge mapping using a bone caliper with CBCT. However, the accuracy of ridge mapping on a cast (Cb=99.42%) was the highest, followed by ridge mapping using a bone caliper (Cb=82.61%). The analysis concluded that both techniques are equivalent to CBCT and can be used interchangeably. CONCLUSION: The mean alveolar ridge width of the occlusal radiograph was the highest, followed by CBCT, ridge mapping on a cast, and ridge mapping using a bone caliper the least (occlusal radiograph > CBCT > ridge mapping on cast >ridge mapping using bone caliper). But at the same time, it can also be used interchangeably.

Comparative Analysis of Three Different Impression Techniques for Impression Defects and Dimensional Accuracy Using a Digital Intraoral Scanner for Fixed Partial Dentures: An In Vivo Study.

AIM: To evaluate the impression defects and compare the dimensional accuracy of three different impression techniques (single-step, two-step without spacer, two-step with spacer) for fixed partial dentures using a digital intraoral scanner in the anterior maxillary region. MATERIALS AND METHODS: Thirty subjects, above the age of 18 years with maxillary central/lateral incisor requiring fixed prostheses were selected according to the inclusion and exclusion criteria. The impressions were rated and evaluated using Heine C2.3K Binocular loupes (Heine Ltd., Dover, NH, USA). An intraoral scanner and digital vernier calipers were used to study and compare the dimensional accuracy of all three impression techniques.  Results: Statistical analysis using the chi-square test revealed that the single-step double mix technique showed the least number of defects (40%), followed by the two-step without spacer (56.7%) and then the two-step with spacer (80%) impression techniques. Using Kruskal Wallis and Mann Whitney U test for dimensional accuracy, it was found that the two-step with spacer impression technique was closer to the control group (intraoral scanner) followed by the two-step without spacer and then the single-step double mix impression techniques. CONCLUSION: All three impression techniques showed the presence of impression defects, mainly voids and bubbles. The single-step double mix and two-step without spacer techniques had more favourable outcomes compared to the two-step with spacer impression technique. The two-step with spacer impression technique was dimensionally more accurate compared to the two-step without spacer and single-step double mix techniques for fixed partial dentures.

What problems associated with ageing are seen in a specialist service for older people living with HIV?

OBJECTIVES: By 2030 the majority of the people living with HIV in the United Kingdom will be over the age of 50. HIV services globally must adapt to manage people living with HIV as they age. Currently these services are often designed based on data from the wider population or from the experiences of HIV clinicians. This article aims to help clinicians designing inclusive HIV services by presenting the most common needs identified during the first year of a specialist clinic for older people living with HIV at the Ian Charleson Day Centre, Royal Free Hospital in London, United Kingdom. METHODS: The records of all thirty-five patients attending the inaugural nine sessions were reviewed. RESULTS: The median age of attendees was 69 (53-93) with 77% being male, 63% being White, 49% being heterosexual and 97% being virally suppressed respectively. The majority (83%) met the criteria for frailty using the Fried frailty phenotype. Eighteen issues linked to ageing were identified with the most common being affective symptoms (51%), memory loss (37%) and falls (29%). CONCLUSIONS: Whilst older people living with HIV are a heterogeneous group frailty is common and appears to present earlier. HIV services either need to adapt to meet these additional needs or must support users in transitioning to existing services. We feel that our multidisciplinary model is successful in identifying problems associated with ageing in people living with HIV and could be successfully replicated elsewhere.