Unusual Defect-Related Room-Temperature Emission from WS2 Monolayers Synthesized through a Potassium-Based Precursor.

Alkali-metal-based synthesis of transition metal dichalcogenide (TMD) monolayers is an established strategy for both ultralarge lateral growth and promoting the metastable 1T phase. However, whether this can also lead to modified optical properties is underexplored, with reported photoluminescence (PL) spectra from semiconducting systems showing little difference from more traditional syntheses. Here, we show that the growth of WS2 monolayers from a potassium-salt precursor can lead to a pronounced low-energy emission in the PL spectrum. This is seen 200-300 meV below the A exciton and can dominate the signal at room temperature. The emission is spatially heterogeneous, and its presence is attributed to defects in the layer due to sublinear intensity power dependence, a noticeable aging effect, and insensitivity to washing in water and acetone. Interestingly, statistical analysis links the band to an increase in the width of the A1g Raman band. The emission can be controlled by altering when hydrogen is introduced into the growth process. This work demonstrates intrinsic and intense defect-related emission at room temperature and establishes further opportunities for tuning TMD properties through alkali-metal precursors.

Solution-Mediated Inversion of SnSe to Sb2Se3 Thin-Films.

New facile and controllable approaches to fabricating metal chalcogenide thin films with adjustable properties can significantly expand the scope of these materials in numerous optoelectronic and photovoltaic devices. Most traditional and especially wet-chemical synthetic pathways suffer from a sluggish ability to regulate the composition and have difficulty achieving the high-quality structural properties of the sought-after metal chalcogenides, especially at large 2D length scales. In this effort, and for the first time, we illustrated the fast and complete inversion of continuous SnSe thin-films to Sb2Se3 using a scalable top-down ion-exchange approach. Processing in dense solution systems yielded the formation of Sb2Se3 films with favorable structural characteristics, while oxide phases, which are typically present in most Sb2Se3 films regardless of the synthetic protocols used, were eliminated. Density functional theory (DFT) calculations performed on intermediate phases show strong relaxations of the atomic lattice due to the presence of substitutional and vacancy defects, which likely enhances the mobility of cationic species during cation exchange. Our concept can be applied to customize the properties of other metal chalcogenides or manufacture layered structures.

The effect of elevated temperatures on excitonic emission and degradation processes of WS2 monolayers.

Controlled heating experiments in an inert environment have been performed on WS2 monolayers, in order to clarify the conflicting reports on the high-temperature photoluminescent response of 2D TMDs. We find that in contrast to some previous results on both WS2 and MoS2, the photoluminescent intensity shows a consistent reduction above room temperature. This is accompanied by an almost linear redshift of the peak maximum, and a nearly linear increase in the peak width, which is attributed to an enhanced interaction with optical phonons. Moreover, by fitting the photoluminescence integral intensity with an Arrhenius type dependence, we demonstrate that the center of the WS2 monolayer flake starts to undergo irreversible degradation at a temperature of 573 K in an inert environment. Regions close to flake edges in contrast, with a more intense room temperature PL response, remain stable. The macroscopic PL signal is largely recovered in these regions following subsequent cooling to room temperature.

Postdeposition Processing of SnS Thin Films and Solar Cells: Prospective Strategy To Obtain Large, Sintered, and Doped SnS Grains by Recrystallization in the Presence of a Metal Halide Flux.

Postdeposition treatments (PDTs) are common technological approaches to achieve high-efficiency chalcogenide solar cells. For SnS, a promising solar cell material, most PDT strategies to control the SnS properties are overwhelmingly based on an annealing in sulfur-containing ambient atmosphere that is described by condensed-state reactions and vapor-phase transport. In this work, a systematic study of the impact of PDTs in a N2 atmosphere, ampules at temperatures between 400 and 600 °C, and a SnCl2 treatment at 250-500 °C on the properties of SnS films and SnS/CdS solar cells prepared by close-spaced sublimation is reported. The ampule and N2 annealing conditions do not affect the grain size of the SnS layers but significantly impact the concentration of intrinsic point defects, carrier density, and mobility. Annealing at 500-600 °C strongly enhances the hole concentration and decreases the carrier mobility, having detrimental impacts on the device performance. SnCl2 treatment promotes grain growth, sintering, and doping by mass transport through the melted phase; it adjusts the hole density and improves the carrier mobility in the SnS layers. SnS/CdS solar cells with an efficiency of 2.8% are achieved in the SnCl2 treatment step, opening new possibilities to further improve the performance of SnS-based devices.