Primary Culture of Dissociated Neurons from the Embryonic Cerebral Cortex.

Primary neuronal culture is a valuable in vitro model for analyzing the molecular mechanisms underlying the development and function of neural circuits. In contrast to neurons in vivo, primary cultured neurons can easily be transfected with genes of interest or treated with chemicals such as agonists and inhibitors of a specific target molecule. Furthermore, time-dependent morphological changes, such as the acquisition of neuronal polarity, axon elongation, and dendrite branch formation, can be analyzed by using primary neuronal cultures. Here, we describe a method for preparing a primary culture of neurons from the developing cerebral cortex, together with a method for gene transfer to primary cultured cortical neurons.

Nanostructuring of Additively Manufactured 316L Stainless Steel Using High-Pressure Torsion Technique: An X-ray Line Profile Analysis Study.

Experiments were conducted to reveal the nanostructure evolution in additively manufactured (AMed) 316L stainless steel due to severe plastic deformation (SPD). SPD-processing was carried out using the high-pressure torsion (HPT) technique. HPT was performed on four different states of 316L: the as-built material and specimens heat-treated at 400, 800 and 1100 °C after AM-processing. The motivation for the extension of this research to the annealed states is that heat treatment is a usual step after 3D printing in order to reduce the internal stresses formed during AM-processing. The nanostructure was studied by X-ray line profile analysis (XLPA), which was completed by crystallographic texture measurements. It was found that the as-built 316L sample contained a considerable density of dislocations (1015 m-2), which decreased to about half the original density due to the heat treatments at 800 and 1100 °C. The hardness varied accordingly during annealing. Despite this difference caused by annealing, HPT processing led to a similar evolution of the microstructure by increasing the strain for the samples with and without annealing. The saturation values of the crystallite size, dislocation density and twin fault probability were about 20 nm, 3 × 1016 m-2 and 3%, respectively, while the maximum achievable hardness was ~6000 MPa. The initial <100> and <110> textures for the as-built and the annealed samples were changed to <111> due to HPT processing.

Provision status of assistive products for cognition to older adults with cognitive impairment among rehabilitation therapists.

Purpose: This study aimed to investigate the provision and need for assistive products for older adults with cognitive impairment among rehabilitation therapists, identify any unmet needs, and analyze current issues in providing such products.Methods: We conducted a questionnaire survey with rehabilitation therapists involved in selecting and providing assistive products for cognitive function in older adults with cognitive impairments. Questionnaires comprising ten items about the experience and need for cognitive assistive products were sent to 300 facilities for older adults in Japan between January and February 2021. One hundred thirty-five responses were received.Results: The mean age of the participants was 39.5 ± SD7.1. There were 70 females, 64 males, and one unanswered questionnaire. In total, 72 (53.3%) of the 135 therapists had introduced or provided assistive products to their patients. The most frequently provided products were for safety and security; some were provided to support memory and orientation. 86% of therapists did not use the insurance system to provide them. The survey showed that most participants with experience providing assistive products needed information on the available resources.Conclusions: Although the need for assistive products for cognition is increasing, they are not sufficiently supplied in caring for older adults with cognitive impairment. Their availability differed depending on the assistive product type. It is necessary to have an effective social insurance system and access to up-to-date information to provide appropriate assistive products.

Assistive products are still underutilized in dementia care. This is despite the strong recognition among rehabilitation professionals, with experience providing assistive products for cognition, that assistive products are necessary for older adults with cognitive impairment.Professionals need access to information to provide appropriate assistive products to aid cognition. Improving public insurance systems and information accessibility can support rehabilitation professionals in providing effective assistive products for older adults with cognitive impairment.

An Overview on the Effect of Severe Plastic Deformation on the Performance of Magnesium for Biomedical Applications.

There has been a great interest in evaluating the potential of severe plastic deformation (SPD) to improve the performance of magnesium for biological applications. However, different properties and trends, including some contradictions, have been reported. The present study critically reviews the structural features, mechanical properties, corrosion behavior and biological response of magnesium and its alloys processed by SPD, with an emphasis on equal-channel angular pressing (ECAP) and high-pressure torsion (HPT). The unique mechanism of grain refinement in magnesium processed via ECAP causes a large scatter in the final structure, and these microstructural differences can affect the properties and produce difficulties in establishing trends. However, the recent advances in ECAP processing and the increased availability of data from samples produced via HPT clarify that grain refinement can indeed improve the mechanical properties and corrosion resistance without compromising the biological response. It is shown that processing via SPD has great potential for improving the performance of magnesium for biological applications.

Influence of Degree of Severe Plastic Deformation on Thermal Stability of an HfNbTiZr Multi-Principal Element Alloy Processed by High-Pressure Torsion.

Severe plastic deformation (SPD) is an effective route for the nanocrystallization of multi-principal element alloys (MPEAs). The stability of the refined microstructure is important, considering the high temperature applications of these materials. In the present study, the effect of SPD on the stability of a body-centered cubic (bcc) HfNbTiZr MPEA was investigated. SPD was performed using a high-pressure torsion (HPT) technique by varying the number of turns between ½ and 10. The evolution of phase composition and microstructure was studied near the disk centers and edges where the imposed strain values were the lowest and highest, respectively. Thus, the shear strain caused by HPT varies between 3 (½ turn, near the center) and 340 (10 turns, near the edge). It was found that during annealing up to 1000 K, the bcc HfNbTiZr alloy decomposed into two bcc phases with different lattice constants at 740 K. In addition, at high strains a hexagonal close packed (hcp) phase was formed above 890 K. An inhomogeneous elemental distribution was developed at temperatures higher than 890 K due to the phase decomposition. The scale of the chemical heterogeneities decreased from about 10 µm to 30 nm where the shear strain increased from 3 to 340, which is similar to the magnitude of grain refinement. Anneal-induced hardening was observed in the MPEA after HPT for both low and high strains at 740 K, i.e., the hardness of the HPT-processed samples increased due to heat treatment. At low strain, the hardness remained practically unchanged between 740 and 1000 K, while for the alloy receiving high strains there was a softening in this temperature range.

Synthesis of a bulk nanostructured metastable Al alloy with extreme supersaturation of Mg.

Nanostructuring of bulk metals is now well documented with the development of severe plastic deformation (SPD) for improving the physical and mechanical properties of engineering materials. Processing by high-pressure torsion (HPT), which was developed initially as a grain refinement technique, was extended recently to the mechanical bonding of dissimilar metals during nanostrcturing which generally involves significant microstructural heterogeneity. Here we introduce, for the first time, a bulk metastable Al-Mg supersaturated solid solution by the diffusion bonding of separate Al and Mg metal solids at room temperature using HPT. Exceptional hardness was achieved homogeneously throughout the metastable alloy with a record maximum supersaturated Mg content of ~38.5 at.% in the Al matrix having a grain size of ~35-40 nm. Our results demonstrate the synthesis of a bulk nanocrystalline metastable alloy with good microstructural stability at room temperature where such bulk solids are not yet reported for mechanical alloying by powder metallurgy.

Publisher Correction: Superplasticity in a lean Fe-Mn-Al steel.

The original PDF version of this Article omitted to state that "Jeongho Han and Seok-Hyeon Kang contributed equally to this work" in the affiliations section. This has now been corrected in the PDF version of the Article. The HTML version was correct from the time of publication.

Superplasticity in a lean Fe-Mn-Al steel.

Superplastic alloys exhibit extremely high ductility (>300%) without cracks when tensile-strained at temperatures above half of their melting point. Superplasticity, which resembles the flow behavior of honey, is caused by grain boundary sliding in metals. Although several non-ferrous and ferrous superplastic alloys are reported, their practical applications are limited due to high material cost, low strength after forming, high deformation temperature, and complicated fabrication process. Here we introduce a new compositionally lean (Fe-6.6Mn-2.3Al, wt.%) superplastic medium Mn steel that resolves these limitations. The medium Mn steel is characterized by ultrafine grains, low material costs, simple fabrication, i.e., conventional hot and cold rolling, low deformation temperature (ca. 650 °C) and superior ductility above 1300% at 850 °C. We suggest that this ultrafine-grained medium Mn steel may accelerate the commercialization of superplastic ferrous alloys.Research in new alloy compositions and treatments may allow the increased strength of mass-produced, intricately shaped parts. Here authors introduce a superplastic medium manganese steel which has an inexpensive lean chemical composition and which is suited for conventional manufacturing processes.

Micro-Mechanical Response of an Al-Mg Hybrid System Synthesized by High-Pressure Torsion.

This paper summarizes recent efforts to evaluate the potential for the formation of a metal matrix nanocomposite (MMNC) by processing two commercial bulk metals of aluminum and magnesium alloy through high-pressure torsion (HPT) at room temperature. After significant evolutions in microstructures, successful fabrication of an Al-Mg hybrid system was demonstrated by observing unique microstructures consisting of a multi-layered structure and MMNC. Moreover, the evolution of small-scale mechanical properties was examined through the novel technique of nanoindentation and the improvement in plasticity was estimated by calculating the strain rate sensitivity of the Al-Mg hybrid system after HPT. The present paper demonstrates that, in addition to conventional tensile testing, the nanoindentation technique is exceptionally promising for ultrafine-grained materials processed by HPT, where the samples may have small overall dimensions and include heterogeneity in the microstructure.

Derivatization of chiral carboxylic acids with (S)-anabasine for increasing detectability and enantiomeric separation in LC/ESI-MS/MS.

A simple and practical derivatization procedure for increasing the detectability and enantiomeric separation of chiral carboxylic acids in LC/ESI-MS/MS has been developed. (S)-Anabasine (ANA) was used as the derivatization reagent and rapidly reacted with carboxylic acids [3-hydroxypalmitic acid (3-OH-PA), 2-(ß-carboxyethyl)-6-hydroxy-2,7,8-trimethylchroman (γ-CEHC), and etodolac] in the presence of 4-(4,6-dimethoxy-1,3,5-triazin-2-yl)-4-methylmorpholium chloride. The resulting ANA-derivatives were highly responsive in ESI-MS operating in the positive-ion mode and gave characteristic product ions during MS/MS, which enabled sensitive detection using selected reaction monitoring; the detection responses of the ANA-derivatives were increased by 20-160-fold over those of the intact carboxylic acids and the limits of detection were in the low femtomole range (1.8-11 fmol on the column). The ANA-derivatization was also effective for the enatiomeric separation of the chiral carboxylic acids; the resolution was 1.92, 1.75, and 2.03 for 3-OH-PA, γ-CHEC, and etodolac, respectively. The derivatization procedure was successfully applied to a biological sample analysis; the derivatization followed by LC/ESI-MS/MS enabled the separation and detection of trace amounts of 3-OH-PA in neonatal dried blood spot and γ-CEHC in human saliva with a simple pretreatment and small sample volume.